Child Craft 10031 User manual

1
Directions for Maintenance, Cleaning, Storage and Use of your Crib are also included.
BEFORE STARTING THE ASSEMBLY PROCEDURE, READ ALL DIRECTIONS WITH CARE.
YOU WILL NEED THE FOLLOWING FOR THE ASSEMBLY OF YOUR CRIB/TODDLER BED:
#1 and #2 Phillip Screwdrivers Slotted Screwdriver Enclosed Allen Wrenches B
Assembly Directions AnD PArts list
crib/toDDler beD
10031
PArts encloseD in cArton
J
(2) Stationary Sides
K
(2) End Panels
(1) Crib Stretcher (for use with Toddler Bed only)
I
PArts encloseD in HArDwAre bAg (noted when shown actual size)
(8) Allenhead Bolts
(actual size)
(2) Allen Wrenches B(4) Flat Head Bolt D
F
(actual size)
(6) Allenhead Bolts
(actual size)
(12) Connector Nuts C
A
(actual size)
G
(2) Allenhead Bolts
(actual size)
H
(2) Joint Connector Nut
tHis is tHe Assembly instrUctions
For cribs solD in tHe UniteD stAtes
•5216 Portside Dr., Medina, OH 44256 USA •PH: 330.722.5033 •FAX: [phone]
E
(4)
WaSherS
Pouches
(storage for
Assembly Directions)
L
(1) Spring
N
(2) Spring
Brackets - Left
M
(2) Spring
Brackets - Right
www.childcraftbaby.com
Foundations Worldwide, Inc.
AB20165C

2
Attach Spring Bracket-Right (M) and Spring Bracket-Left (N) to Mattress Support Assembly (L) using a Flat Head Bolt (D), a
Washer (E) and a Connector Nut (C).
Note: Each Flat Head Bolt (D) has a friction enhancing patch applied to the threads which will cause some resistance during the
tightening process.
Tighten each bracket until it is secure, but allows each bracket to be easily rotated by hand. Place each bracket at a 45 degree angle
as shown.
steP 1 - DiAgrAm 1: moUnting brAckets tosPring
PrePArAtion
Carefully remove and lay out all hardware and parts. During the assembly process, when using screws or bolts (fastening devices),
check each with
PArts encloseD in HArDwAre bAg
list by letter and size. Identify by placing each fastening device on the diagram of
the item (sketched actual size). Be sure to use the proper size specied in the assembly directions. Hardware Bag may contain extra
fastening devices. Check quantities and match to
PArts encloseD in HArDwAre bAg/cArton
lists. If a part is missing or broken, DO NOT
return the product to your dealer. Call Foundations®for assistance at 877.716.2757 (U.S. Only) or 330.722.5033 (Monday through Friday,
9:00 a.m.– 4:00 p.m. Eastern Time). Before making this contact identify your crib. Model Identication numbers are stamped on a label
attached to the inside face of a End Panel K bottom rail. Record the complete model identication number now: Include this number with
a request for a part or literature for your crib. Do not sUbstitUte PArts! #____________________.
D
N
L
C
E
45 Degrees
M
N
M
Pouches are on top
surface with printed
text facing up.
Meets CSPC
Safety Requirements

3
steP 3 - DiAgrAm 3: AttAcH sPring to crib
Select the height position you want to mount
the Spring Assembly L. Refer to warnings
on page 6 and 7 before making this selection.
Carefully guide the Spring Assembly Lfrom
Step 1 down into the crib by rst tilting the
spring at approximately 10 degrees as shown.
Positon mounting anges on spring hangers
between the posts. Attach spring brackets to
the crib posts using Bolt F.
Place the (8) Connector Nuts Cinto their holes in the corner
posts of End Panel Kas shown. Align the holes in an end rail
of a Stationary Side Jwith the holes in End Panel K. Insert
Allenhead Bolts Athrough the end rail on Stationary Side
J, then tighten into Connector Nuts Cin End Panel Kby
using the two Allen Wrenches B. DO NOT OVERTIGHTEN.
Repeat this process at the other three corner posts.
steP 2 - DiAgrAm 2: AttAcH stAtionAry siDeSto FootboArD/HeADboArD
J
B
A
C
C
B C
Note: Large
overhang goes
toward outside
of crib.
K
Flanges on spring
hangers t between
posts.
L
Spring Mounting Positions:
Top
Middle
Bottom
B
F
F
Insert Bolt Fthrough mounting hole in Spring
Brackets Mand Nand thread into the
factory installed insert located in each crib
post using Allen Wrench B. Tighten securely.
DO NOT OVERTIGHTEN.
To adjust height of Spring L, remove
Bolts Fand move Spring Lto the
other height locations shown in the
diagram above. Install Bolts Fas
described above.

4
Place a purchased mattress on Spring L.
After completing crib assembly, review Warnings on page 7. Also review Cautions, Cleaning, Storage, Use and Maintenance of crib
on pages 6 and 7. Store the assembly directions in the pouch which was pre-attached to Spring L. For future referral to assembly
directions you will only need to remove them from the pouch. We caution you not to store excess hardware in pouch as this would be a
danger to child if retrieved by him/her.
Check periodically to be sure screws and bolts (fastening devices) remain tight as instructed in warnings on page 7 of these
assembly directions.
steP 4: FinisHing toUcHes

5
When use as a crib has been completed, you have the option to convert your crib to a toddler bed for years of additional use in your
child's room. Remove one Stationary Side J and install Spring L in its lowest position. Store removed parts and hardware as perhaps
sometime in the future you may want to convert the toddler bed
back into a crib. Install Allenhead Bolt F and Connector Nut
C in top hole of each End Panel Kpost as shown and
tighten securely. Locate the dowel pins in the ends of
Stretcher Iinto their holes in End Panels K. Insert
Allenhead Bolts Gthrough their holes in End Panel
Kand into Stretcher Ialigning the threaded hole in
Joint Connector Nut H. You can use a at tipped
screwdriver in the slotted end of the Joint Connector
Nut Hto hold and rotate it to help to align it with the
Allenhead Bolt G. Tighten securely. Review warnings
on page 6. Place Assembly Directions back into the
pouch attached to Spring L.
• Again check to be sure each bolt is tightened
securely, then check frequently to be sure all
remain tightened.
toDDler beD conversion
K
G
K
H
I
C
G
H
I
(post)
(top edge)
K
instAlling A gUArD rAil
For added security, a guard rail can be purchased for this crib. Contact Foundations®or your dealer.
NOTE: Allen Head Bolt Aand Connector Nuts Cwill be required to install the guard rail. Keep all parts and these instructions for future
reference.
Stretcher I Installed

6
WARNING (For Toddler Bed)

!
WARNING:INFANTS HAVE DIED IN TODDLER BEDS FROM
ENTRAPMENT. Openings in and between bed parts can entrap head and neck
of a small child. NEVER use bed with children younger than 15 months.
ALWAYS follow assembly instructions.
WARNING: STRANGULATION HAZARD: NEVER place bed near windows
where cords from blinds or drapes may strangle a child. NEVER suspend strings
over bed. NEVER place items with a string, cord or ribbon, such as hood strings
or pacier cords, around a child’s neck. These items may catch on bed parts.
CAUTION: ENTRAPMENT HAZARD: To avoid dangerous gaps, any
mattress used in this bed shall be a full-size crib mattress at least 51 5/8 in.
(1310 mm) in length, 27 1/4 in. (690 mm) in width, and 4 in. (100 mm) in thickness.
•The users maximum weight shall not be greater than 50 lbs. (22.7 kg).
•Mattress MUST be moved into lowest position for proper positioning behind
stretcher.
•This crib contains all components necessary to convert to a toddler bed. However,
a guardrail may be available for purchase to provide additional security. Contact
Foundations®for assistance. Refer to maintenance section for contact information.
!
!
!
MAINTENANCE OF YOUR CRIB/TODDLER BED: Upon completion of the assembly, check to ensure that all screws, bolts and fastening
devices have been tightened securely. There should be a frequent check of this product for damaged hardware, loose joints, missing parts
or sharp edges before and after assembly and frequently during use. DO NOT use crib if any parts are missing or broken. If any parts are
missing or broken or you need assistance with assembly, DO NOT return the product to your dealer. Call Foundations®for assistance
at 877.716.2757 (U.S. Only) or 330.722.5033 (Monday through Friday, 9:00 a.m.– 4:00 p.m. Eastern Time) for replacement parts and
instructional literature if needed. Include model identication numbers which you recorded on page 2. DO NOT substitute parts.
CLEANING INSTRUCTIONS FOR YOUR CRIB/TODDLER BED: Mix together a mild solution of gentle dishwashing liquid and water,
apply to surface using a soft clean cloth lightly dampened in the solution. Rinse with clear water again using a soft clean cloth, then dry all
surfaces thoroughly with a soft dry cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL, OR COARSE RAGS SHOULD
BE USED TO CLEAN THIS FINE FURNITURE.
STORAGE AND USE OF YOUR CRIB/TODDLER BED:A printed pouch is attached to the crib spring for the permanent storage of
the assembly directions. After completing the assembly process you are advised to read and be aware of all WARNINGS, CAUTIONS,
CLEANING, STORAGE, USE AND MAINTENANCE notices contained in this set of directions and printed on the pouch located on the
crib spring. You will then place the complete set of assembly directions into the pouch for future referral. We caution you not to place ex-
cess hardware in the pouch as it could present danger to a child if retrieved. When storing crib use CAUTION as extreme temperature or
humidity changes could be harmful. Use CAUTION when a vaporizer is in use, always aim vapor stream away from crib as well as away
from any wood furniture item.
CAUTION
•ANY MATTRESS USED IN THIS CRIB SHALL BE AT LEAST 27 1/4 BY 51 5/8 IN. WITH A
THICKNESS NOT EXCEEDING 6 IN. IF YOUR CRIB IS DESIGNED TO CONVERT TO A
TODDLER BED, THE MATTRESS MUST BE AT LEAST 4 IN. (100 MM) THICK.
•UPON COMPLETION OF ASSEMBLY BE SURE ALL SCREWS, BOLTS AND FASTENING
DEVICES HAVE BEEN TIGHTENED SECURELY. A FREQUENT CHECK SHOULD BE MADE
OF ALL SCREWS, BOLTS AND FASTENING DEVICES AND TIGHTEN IF NEEDED.

7
WARNING
•FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH.
WARNING: Infants can suffocate on soft bedding. NEVER add a pillow
or comforter. NEVER place additional padding under an infant.
•Read all instructions before assembling crib. Keep instructions for future use. A pouch is
attached to crib for permanent storage of the instructional literature.
• To reduce the risk of SIDS pediatricians recommend healthy infants be placed on their backs
to sleep, unless otherwise advised by your physician.
• Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such
as hood strings or pacier cords. DO NOT suspend strings over a crib or attach strings to toys.
• To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or
clothing on loose fasteners.
• DO NOT place crib near window where cords from blinds or drapes may strangle a child.
• When child is able to pull to standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
•Stop using crib when child begins to climb out or reaches the height of 35 in. (89 cm).
• After raising side, make sure latches are secure (if your unit has a moveable side).
• DO NOT leave child in crib with side lowered. Be sure side is in raised and locked position
whenever child is in crib (if your crib has a moveable side).
• Check this product for damaged hardware, loose joints, loose bolts or other fasteners,
missing parts or sharp edges before and after assembly and frequently during use. Securely
tighten bolts and other fasteners. DO NOT use crib if any parts are missing, damaged or
broken. If any parts are missing or broken or you need assistance with assembly, DO NOT return
the product to your dealer. Call Foundations®for assistance at 1 877.716.2757 (U.S. Only) or
+1 330.722.5033 (Monday through Friday, 9:00 a.m.– 4:00 p.m. Eastern Time) for replacement parts
and instructional literature if needed. Include model identication numbers with your request
which you recorded on page 2. DO NOT substitute parts.
• Replace teething rail(s) if damaged, cracked, or loose (if equipped with teething rails).
• If renishing, use a non-toxic nish specied for children’s products.
• Follow warnings on all products in a crib.
• NEVER use plastic shipping bags or other plastic lm as mattress covers because they can
cause suffocation.
• Infants can suffocate in gaps between crib sides and a mattress that is too small.
• DO NOT use a water mattress with this crib.
• When disassembling this crib, DO NOT remove any item attached with wood screws.
!

!
5216 Portside Dr.
Medina, OH 44256 USA
Telephone: [phone] (U.S. Only)
or 330.722.5033
Fax: [phone]
www.childcraftbaby.com