Child Craft CONVERTS TO TODDLER BED AND FULL SIZE HEADBOARD AND... User manual

H02782:01/05 1
(4) Scissor Arm
Assemblies A
(2) End Plates
- Right E
H01206
H01214
(8) Allenhead Bolts G
H01169
(actualsize)
(2) End Plates - Left D
H01205
(20) Lock Nuts C
H00133
(20) Pan Head Machine
Screws B
H00132 (8) K-D Bolt Plugs Z
(actualsize)
H00161
(actualsize)
(8) Slotted/Phillips
Machine Screws F
H00117
(8) Allenhead Bolts J
(actualsize)
H01162
(8) Allenhead Bolts K
(actualsize)
H01174 (10) Insert Nuts L
(actualsize)
H00136
(1) Stretcher X(for use on Toddler Bed only)
(2) Foot
Posts Q(2) Stationary Posts T
(1) Stationary Side U
(1) Long Foot Side V
(1) Short Foot
Section S
(1) Short Head
Section R
(1) Spring O
plastic pouch
for storage of
Assembly
Directions
(2) Stabilizing Bars P(attached to Spring O )
(1) Top Rail W
(2) Allenhead Bolts N
(actualsize)
(11) Allenhead Bolts M
(actualsize)
(1) Allen
Wrench i
H00280
(1) Allen
Wrench I
H01105
(actualsize) (actualsize)
(16) K-D Bolt Plugs H
H00147 (actual size)
DirectionsforMaintenance,Cleaning, Storageand Useof yourChild CraftBed arealso included.
MM
MM
MBEFORESTARTINGTHEASSEMBLY PROCEDURE,READ ALLDIRECTIONS WITHCARE.
MM
MM
MYOU WILL NEED THE FOLLOWING FOR THE ASSEMBLY OF YOUR CHILD CRAFT BED:


slotted screwdriver 

7/16" wrench or adjustable wrench 

enclosed Allen Wrenches i& I
CONVERTSTO TODDLER BEDAND
FULLSIZEHEADBOARDAND FOOTBOARD
ASSEMBLY DIRECTIONS AND PARTS LIST
CRIB’N’DOUBLEBED
CHILDCRAFTINDUSTRIES,INC.
P.O.Box444,Salem,IN USA 47167-0444 PH:1-877-265-9046 FAX:[phone] http://www.childcraftindustries.com
PARTS ENCLOSEDINCARTON
child craft
PARTS ENCLOSED IN HARDWARE BAG (NOTED WHEN SHOWN ACTUAL SIZE)

H02782:01/052
CONTACT US
To report missing parts or
manufacturing defects,
PLEASE CONTACT US
for customer assistance.
1-877-265-9046
(please have model # available when calling)
CHILDCRAFT INDUSTRIES,INC.
Customer Service Dept.
P.O. Box 444
Salem,Indiana 47167-0444
www.childcraftindustries.com
FAX: [phone]

H02782:01/05 3
Attach the short section of the (4) Scissor Arm Assemblies AA
AA
Ato Spring OO
OO
Ousing (4) Pan Head Machine Screws BB
BB
Band (4) Lock Nuts CC
CC
Cplaced exactly
as shown in Diagram 1. NOTE: The metal threads of Lock Nuts
C to be inserted first over Pan Head Machine Screws
BB
BB
B as shown in Enlarged
Section View . Be sure to use the proper receiving holes in Spring
OO
OO
Oas shown . This procedure will be accomplished from the underside of Spring
OO
OO
O. Tighten all (4) Pan Head Machine Screws BB
BB
Bwhile holding Lock Nuts CC
CC
Cwith a 7/16 inch wrench. Tighten each assembly securely.
Carefully remove and lay out all hardware and parts. During the assembly process whenever using screws or bolts (fastening devices), check each with
this hardware list, by letter and size identify by placing each fastening device on the diagram of the item which is sketched actual size. Be sure to use
the proper size specified in the assembly directions. Hardware Bag may contain extra fastening devices. Check quantities and match to Hardware Bag
andCartonParts Lists.IfapartismissingorbrokencontactChildCraftatPH:1-877-265-9046,FAX:[phone],http://www.childcraftindustries.com
for a replacement part or instructional literature. Before making this contact identify your crib. Model Identification numbers are on a label attached to the
inside face of Short Foot Section SS
SS
Sbottom rail. Record the complete model identification number now: #____________________. Include this number with
a request for a part or literature for your crib. DO NOT SUBSTITUTE PARTS!
Mount an End Plate - Right EE
EE
Eand an End Plate - Left DD
DD
Dto ends of each Stabilizing Bar PP
PP
Pusing (4) Pan Head Machine Screws BB
BB
Band (4) Lock Nuts
CC
CC
Cin each Stabilizing Bar PP
PP
Pexactly as shown. IMPORTANT: End Plates DD
DD
D& EE
EE
Emust be positioned in the correct mounting holes to Stabilizing
Bars PP
PP
Pexactly as shown. Tighten down Pan Head Machine Screws BB
BB
Band Lock Nuts CC
CC
Csecurely using a phillips screwdriver and a 7/16 inch wrench.
See Enlarged View
UNDERSIDEOFSPRINGOO
OO
O
B
A
C
A
O
Long arm of Scissor Arm Assembly A
Short arm of Scissor Arm Assembly A
Long arm of
Scissor Arm
Assembly A
Short arm of
Scissor Arm
Assembly A
Plastic pouch
Lowest position
Middle position
Highest position
B
A
O
C
Enlarged View
Plastic insert in
Lock Nut C
See Enlarged View
B
D
P
Enlarged View
Plastic insert in
Lock Nut C
B
E
slot
slot
PB
Dor EEnd Plate
INSTALL END PLATES DD
DD
D&
EE
EE
EEXACTLY AS SHOWN C
C
STEP 1 - DIAGRAM 1: ASSEMBLE SPRING
P REPARATION
STEP 2-DIAGRAM 2:ASSEMBLE STABILIZING BARS

H02782:01/054
Attach a Foot Post Qand Stationary Post
Tto Short Head Section Ras shown.
Lay the three parts horizontal on a soft
surface (carpet) and insert Allenhead Bolt
Gthrough top hole in Foot Post Qand
into hole in Short Head Section R. Insert
K-D Bolt Plug Hinto hole in Short Head
Section Ras shown, aligning its threaded
hole with the threads onAllenhead Bolt G.
Hold K-D Bolt Plug Hin position with a
slotted screwdriver and begin to tighten
Allenhead Bolt Gusing Allen Wrench i.
DO NOT fully tighten at this time. Insert
Allenhead Bolt Gthrough bottom hole in
Foot Post Qand into hole in Short Head
Section R. Insert K-D Bolt Plug Hinto
hole in Short Head Section Ras shown,
aligning its threaded hole with the threads
onAllenhead BoltG. HoldK-D BoltPlugH
in position with a slotted screwdriver and
begin to tighten Allenhead Bolt Gusing
Allen Wrench i. Once bothAllenhead Bolts
Gare properly aligned and both are par-
tially tightened, tighten securely usingAllen
Wrench i. Follow the same procedure for
attaching Stationary Post Tto Short Head
Section Rand the other Foot Post Qand
Stationary Post Tto Short Foot Section S.
Insure all (8)Allenhead Bolts Ghave been
tightened securely before continuing with
next step.
Lay Short Head Section RR
RR
Rand Short Foot Section SS
SS
Sdown horizontally, (outside facing down) as shown. Insert a Slotted/Phillips Machine Screw FF
FF
F
intoeachtopthreadedinsert(toponly)onbothShortHeadSectionRR
RR
RandShortFootSectionSS
SS
S.LeavetheseSlotted/PhillipsMachineScrewsFF
FF
Fextended
(only allow Screws F to penetrate two to three revolutions into top insert), as shown. While Short Foot Section SS
SS
Sis still in a horizontal position, place
keyhole in End Plate EE
EE
E(attached to a Stabilizing Bar PP
PP
P) over installed extended Screw FF
FF
F being careful to place exactly as shown. Insert another
Screw FF
FF
F into the bottom insert and tighten both screws. Attach the remaining Stabilizing Bar PP
PP
P to Short Foot Section SS
SS
S in the same manner, again
pay close attention to insure placement is exactly as shown. Tighten Screws FF
FF
Fsecurely. Set Short Foot Section SS
SS
Supright and align Screws FF
FF
Fin
Short Head Section RR
RR
Rwith the free end of each Stabilizing Bar PP
PP
P. Let top extended Screws FF
FF
F on inside of Short Head Section RR
RR
R receive keyhole
in End Plates DD
DD
Dand EE
EE
Eon Stabilizing Bars PP
PP
P. Add a Screw FF
FF
Fto each of the two bottom threaded inserts and tighten securely.
H
H
TG
H
G
H
R
i
Q
See
Enlarged View
P
threaded
inserts
F
S
E
D
Bottom hole in
EndPlateEE
EE
E
Keyhole in
EndPlate Extended
Screw FF
FF
F
Enlarged View
T
FP
STEP 3-DIAGRAM 3:ATTACH FOOT POSTS TO SHORT HEAD SECTION AND SHORT FOOT SECTION
STEP 4-DIAGRAM 4:ATTACH STABILIZING BARS TO SHORT HEAD SECTION AND SHORT FOOT SECTION

H02782:01/05 5
READTHISENTIRESTEPBEFORESTARTINGTHEPROCEDURETOSELECTASPRINGOO
OO
O
HEIGHT POSITION AND TO ATTACH SPRING OO
OO
OTO THE STABILIZING BARS PP
PP
P. REVIEW DIAGRAM 1.
1.1.
1.1.
1. Decide on your preference of height placement of Spring OO
OO
O. You have three position choices, highest, middle and lowest holes in Spring OO
OO
Oare
noted in Diagrams 1 and 5. After you select your height, attach one end of the long end of Scissor Arm Assembly AA
AA
Ato Spring OO
OO
Oby first inserting
a Pan Head Machine Screw BB
BB
B through selected position hole in Spring OO
OO
Othen through one end of Scissor Arm Assembly AA
AA
A,add a Lock Nut CC
CC
C,(with
metal threads of Lock Nuts
CC
CC
C
to be inserted first), exactly as shown. Repeat this procedure until one end of each of the (4) Scissor Arm Assemblies
AA
AA
Ais attached to Spring OO
OO
Oat the same height position. Tighten all (4) Pan Head Machine Screws BB
BB
B while holding Lock Nuts CC
CC
C with a 7/16 inch wrench.
Tighten each assembly securely.
2.2.
2.2.
2. Carefully lift Spring OO
OO
Ointo the crib. Spring OO
OO
Owill attach to the outside holes in the two installed Stabilizing Bars PP
PP
P. Insert a Pan Head Machine Screw
BB
BB
B first through the remaining long end of the Scissor Arm Assembly AA
AA
A through the hole in Stabilizing Bar PP
PP
P, add a Lock Nut CC
CC
C (with metal threads
of Lock Nuts
CC
CC
C to be inserted first). See Diagram 5 and follow the procedure exactly. Repeat the procedure with the remaining (3) long ends of the
Scissor Arm Assemblies AA
AA
Ato Stabilizing Bars PP
PP
P. Tighten all (4) Pan Head Machine Screws BB
BB
Bwhile holding Lock Nuts CC
CC
C with a 7/16 inch wrench
and tightening with a phillips screwdriver. Tighten each assembly securely.
3.3.
3.3.
3. Whenever you decide on another height position first remove the crib mattress. Remove Spring OO
OO
Oby detaching the spring from the Stabilizing Bars
PP
PP
Pby loosening and removing the (4) Lock Nuts CC
CC
Cand removing the (4) Pan Head Machine Screws BB
BB
B (installed in
22
22
2 above) by using a 7/16 inch
wrench and a phillips screwdriver. Carefully lift the spring from the crib. Make your selected height position change by following 11
11
1. of this Step. Then
follow 22
22
2.to reinstall Spring OO
OO
O, again tighten all Pan Head Machine Screws BB
BB
Bsecurely as directed.
lowest position
middleposition
highest position Short arm of
Scissor Arm
Assembly AA
AA
A
A
O
B
C
Stabilizer Bars PP
PP
P
with End Plates
DD
DD
D & EE
EE
Eattached
A
NOTE: CRIB IS DELETED FROM
DIAGRAMFORCLARITY&DETAIL.
C
STEP 5-DIAGRAM 5:ATTACH SPRING TO STABILIZING BARS
Long arm of
Scissor Arm
Assembly AA
AA
A

H02782:01/056
MAINTENANCE OF YOUR CHILD CRAFT BED: Upon completion of assembly be sure all screws, bolts and fastening devices have been tightened
securely. A frequent check should be made of all screws, bolts and fastening devices and tightened if needed. Before each usage or assembly, inspect
crib for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use crib if parts are missing or broken. Contact Child Craft at 1-877-
265-9046 or http://www.childcraftindustries.com, for a replacement part or instructional literature if needed. Include Model Identification Number
with your request which you recorded on Page 3 of these instructions. DO NOT SUBSTITUTE PARTS. DO NOT MAKE ANY ALTERATIONS NOT
DESCRIBEDINTHESEASSEMBLYDIRECTIONS.
CLEANING INSTRUCTIONS FOR YOUR CHILD CRAFT BED: Mix togetheramild solutionofgentle dishwashingliquidand water,apply tosurfaceusing
a soft clean cloth lightly dampened in the solution. Rinse with clear water again using a soft clean cloth, then dry all surfaces thoroughly with a soft dry
cloth. NOABRASIVECLEANERS,SCOURINGPADS,STEELWOOL, ORCOARSERAGSSHOULDBE USEDTOCLEANTHISFINEFURNITURE.
STORAGE AND USE OF YOUR CHILD CRAFT BED: Aprinted plastic pouch is attached to the crib spring for the permanent storage of the assembly
directions. After completing the assembly process you are advised to read and be aware of all WARNINGS, CAUTIONS, CLEANING, STORAGE, USE
AND MAINTENANCE notices contained in this set of directions and printed on the plastic pouch located on the underneath side of the crib spring. You
will then place the complete set of assembly directions into the plastic pouch for future referral. We caution you not to place excess hardware in the
plastic pouch as it could present danger to a child if retrieved. When storing crib use CAUTION as extreme temperature or humidity changes could be
harmful. Use CAUTION when a vaporizer is in use, always aim vapor stream away from crib as well as away from any wood furniture item.
SketchB
(style may vary)
CRIB TO FULL SIZE: Disassemble Cribbyremoving the mattress
and Spring O. Also remove Short Head Section Rand Short
Foot Section Sfrom Foot Posts Qand Stationary Posts T.
Store all removed parts and hardware as they will be needed for
future converting. Using (8) Allenhead Bolts Mand (8) K-D Bolt
Plugs Z, attach the Stationary Side Assembly U/T/Wand the
Long Foot Side Assembly V/Qto bed rails and slat roll (Models
#6454 and #6080 sold separately). InstallAllenhead Bolts Kand
Insert Nuts L, (2) of each in each Foot Posts Qand Stationary
Posts Tas shown.
TODDLER BED TO FULL SIZE: Disassemble Toddler Bed by re-
moving the mattress, Stretcher Xand Spring O. Also remove
Short Head Section Rand Short Foot Section Sfrom Foot Posts
Qand Stationary Posts T. Store all removed parts and hard-
ware as they will be needed for future converting. Locate Long
Foot Side V(not used on Toddler Bed). Attach Foot Posts Qto
Long Foot Side Vusing Allenhead Bolts Jand tighten withAllen
Wrench i. Refer to STEP 5 - DIAGRAM 5. Using (8) Allenhead Bolts
Mand (8) K-D Bolt Plugs Z, attach the Stationary SideAssem-
bly U/T/Wand the Long Foot Side Assembly V/Qto bed
rails and slat roll (Models #6454 and #6080 sold separately).
Install Allenhead Bolts Kand Insert Nuts L, (2) of each in each
Foot Posts Qand Stationary Posts Tas shown.
V/Q
U/T/W
Model#6080Slat Roll
K
L
K
L
L
L
Model #6454 Bed Rails
K
K
Sketch A
(style may vary)
WARNING
When use as a crib has been completed, you have the option to
convert to a Toddler Bed for years of additional use in your child’s
room. Refer to STEP 6 - DIAGRAM 6. Remove Long Foot Side V.
Attach Stretcher Xas shown in Sketch A. The dowel on each
end of Stretcher Xlocates in the top hole near the bottom of Foot
Posts Q. Secure with an Allenhead Bolt Mand K-D Bolt Plug
Hat each end (shown installed). Fill the hole near the top of
each Foot Post Qwith an Insert Nut LandAllenhead Bolt Nas
shown. Tighten Allenhead Bolt Nwith Allen Wrench iand Insert
Nut Lwith Allen Wrench I. Spring OO
OO
Omust be installed in
lowest position in order for Stretcher XX
XX
Xto prevent the
mattress from slipping off Spring OO
OO
O. Areas of entrap-
ment could cause serious injury or death. Refer to STEP 5 -
DIAGRAM 5 for changing Spring OO
OO
Oposition. Store the removed
parts and hardware, they will be needed if you wish to convert
your Toddler Bed back to a Crib or into a Full Size Headboard and
Footboard.
PURCHASEDMATTRESS
see size requirements
underWARNING
NOTE: Spring Omust be installed
in lowest position as shown.
 NOTE: When using as a Toddler Bed the mattress must have minimum
dimensions of 51-5/8 in. (1310mm) in length and 27-1/4 in. (690mm) in width
and 4 in. (100mm) in thickness but not to exceed 6 in.
 It is very important that Stretcher XX
XX
Xis used when converting to a Toddler
Bed. Failure to install this part could result in serious injury or death.
 When using as a Toddler Bed, the minimum age shall not be less than 15
months and the maximum weight shall not be greater than 50 lb (22.7 kg).
!
S
N
M
H
H
ML
X
N
RU/T/W
M
M
CONVERT TO FULL SIZE HEADBOARD AND FOOTBOARD
CONVERT TO TODDLER BED

H02782:01/05 7
WARNING
FAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY IN-
STRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
READALL INSTRUCTIONS BEFOREASSEMBLING CRIB. KEEP
INSTRUCTIONS FOR FUTURE USE. A PLASTIC POUCH IS ATTACHED TO
CRIBFORPERMANENTSTORAGEOFTHEINSTRUCTIONALLITERATURE.
BEFORE EACH USAGE OR ASSEMBLY, INSPECT CRIB FOR
DAMAGED HARDWARE, LOOSE JOINTS, MISSING PARTS OR
SHARP EDGES. DO NOT USE CRIB IF ANY PARTS ARE MISSING
OR BROKEN. ASK YOUR DEALER OR WRITE TO Child Craft, P.O.
BOX 444, SALEM, IN 47167-0444 USA 1-877-265-9046 FOR RE-
PLACEMENT PARTS AND INSTRUCTIONAL LITERATURE IF
NEEDED. INCLUDEMODELIDENTIFICATION NUMBERSWITHYOUR REQUESTWHICH
YOU RECORDED ON PAGE THREE. DO NOTSUBSTITUTE PARTS.
AFTER RAISING SIDE, MAKE SURE LATCHES ARE SECURE. IF
YOURUNITHASADROPSIDE.
WHEN CHILD IS ABLE TO CLIMB OUT OR REACHES THE
HEIGHT OF 35 INCHES (90 CENTIMETERS) THE CRIB SHALL NO
LONGER BE USED.
DO NOT PLACE CRIB NEAR WINDOW WHERE CORDS FROM
BLINDS OR DRAPES MAY STRANGLE A CHILD.
IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR
CHILDREN’S PRODUCTS.
DO NOT LEAVE CHILD IN CRIB WITH SIDE LOWERED. BE SURE
SIDE IS IN RAISED AND LOCKED POSITION WHENEVER CHILD
IS IN CRIB.
WHEN CHILD IS ABLE TO PULL TO STANDING POSITION, SET
MATTRESS TO LOWEST POSITIONAND REMOVE BUMPER PADS,
LARGE TOYS AND OTHER OBJECTS THAT COULD SERVE AS
STEPS FOR CLIMBING OUT.
NEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC
FILM AS MATTRESS COVERS BECAUSE THEY CAN CAUSE SUF-
FOCATION.
DO NOT USE A WATER MATTRESS WITH THIS CRIB.
REPLACE TEETHING RAIL(S) IF DAMAGED OR LOOSE. (IF
EQUIPPED WITH TEETHING RAILS.)
STRINGS CAN CAUSE STRANGULATION! DO NOT PLACE
ITEMSWITHASTRINGAROUNDACHILD’SNECK, SUCHAS HOOD
STRINGS OR PACIFIER CORDS. DO NOT SUSPEND STRINGS
OVER A CRIB OR ATTACH STRINGS TO TOYS.
REMOVE ALL CRIB TOYS WHICH ARE STRUNG ACROSS CRIB
AREA WHEN YOUR CHILD IS BEGINNING TO PUSH UP ON HANDS
AND KNEES OR IS 5 MONTHS OF AGE, WHICHEVER OCCURS
EARLIEST. THESE TOYS CAN CAUSE STRANGULATION.
WHENDISASSEMBLING THIS CRIB,DO NOT REMOVEANYITEM
ATTACHED WITH WOOD SCREWS.
ALWAYS ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY
CHECKING REGULARLY, BEFORE PLACING THE CHILD IN THE
CRIB, THAT EVERY COMPONENT IS PROPERLY AND SECURELY
IN PLACE.
ANY MATTRESS USED IN
THIS CRIB MUST BE AT
LEAST 27-1/4 INCHES (69
CENTIMETERS), BY 51-5/8
INCHES (131 CENTIME-
TERS), WITHA THICKNESS
NOT EXCEEDING 6 INCHES
(15 CENTIMETERS).
THEDIMENSIONSOF THEMATTRESS
SHALL BE TAKEN FROM SEAM TO
SEAMOREDGETOEDGEWHEREAP-
PROPRIATE.
UPON COMPLETION OF
ASSEMBLY BE SURE ALL
SCREWS, BOLTSAND FAS-
TENING DEVICES HAVE
BEEN TIGHTENED SE-
CURELY. A FREQUENT
CHECK SHOULD BE MADE
OF ALL SCREWS, BOLTS
AND FASTENING DEVICES
AND TIGHTEN IF NEEDED.

!
CHILDCRAFTINDUSTRIES,INC.
P.O.BOX 444
SALEM, IN 47167-0444 USA
PH:812-883-3111
FAX:[phone]
http://www.childcraftindustries.com
CAUTION