Child Craft Denman F33601 User manual

SINGLE DROPSIDE CRIB
CONVERTS TO DAYBED OR
FULL SIZE HEADBOARD
1
CHILD CRAFT INDUSTRIES, INC.
P.O. Box 444, Salem, IN USA 47167-0444
PH:812-883-3111-FAX: [phone] - http://www.childcraftindustries.com
ASSEMBLY DIRECTIONS AND PARTS LIST
ΦΦ
ΦΦ
ΦREADALLINSTRUCTIONSWITH CAREBEFORE STARTING THEASSEMBLY PROCEDURE.
ΦΦ
ΦΦ
ΦYOU WILL NEED A PHILLIPS SCREWDRIVER, A STANDARD SLOTTED SCREWDRIVER, A 3/8” & 7/16” WRENCH
(or adjustable wrench), AND THE ENCLOSED ALLEN WRENCH K.
PARTS ENCLOSED IN HARDWARE BAG ( NOTED WHEN SHOWN ACTUAL SIZE )
AB DE
(4) F/HPhillips
Wood Screw
(actual size)
(4) Hexhead
Machine Screw
(actual size)
(2) 4-Position Spring Bracket
FG
(1)
Lower
Track
Assembly
(Right)
HI
J
(4) Allenhead K-D Bolts
(actual size)
(actual size)
(2) Upper Tracks
K
L
M
(actual size)
(4) K-D Bolt Plugs
(actual size)
R
Q
(actual size)
(2) Rubber
Washers
(2) Combo
Machine
Screw
(10) Combo Pan Head
Wood Screw
(4) Insert
Locknut
(4) Hole
Button
Covers NO
(1) Sta-Bar Bracket - Left
P
PREPARATION
Carefully remove and lay out all hardware and parts. Check quantities and match the Hardware List and the Parts List. NOTE: During
the assembly process whenever using screws or bolts, check each with the Hardware List by letter and size identification.
Place each screw or bolt on the diagram of the item which is sketched actual size. Be sure to use the proper size specified in
the assembly directions. If a part is missing or broken contact your Child Craft dealer or Child Craft, P.O. Box 444, Salem, IN 47167-
0444 USA, 812-883-3111, http://www.childcraftindustries.com for replacement part(s) or instructional literature. Before making this
contact identify your Crib’n’Double Bed by the model identification number stamped on the inside face or bottom edge of the
Headboard, Footboard or crib sides, or stamped on a label attached to the inside face of Footboard V bottom rail. Make note of all
identification numbers and include this information with your request. DO NOT SUBSTITUTE PARTS!
Recordyourmodelidentificationnumberherefor futureidentification: Model#______________________________________
(1) Allen Wrench
(4) PhillipsPan
HeadMachine
Screw
(actual size) (actual size)
child craft
(1) Sta-Bar Bracket - Right
H00745:11/01
(actual size)
C(1) Hexhead Wrench
(1)
Lower
Track
Assembly
(Left)

PARTS ENCLOSED IN CARTON
2
Y (1) Spring
T (1) Stationary Side U (1) Drop Side
V (1) Footboard X (1) Headboard
S (1) Stabilizing Bar
(Sta-Bar)
STEP 1-DIAGRAM 1:ATTACH HARDWARE TO FOOTBOARD AND HEADBOARD
H00745:11/01
plastic pouch
(HELPFUL HINT: Hardware installation may be
easier if the Footboard V and Headboard X are
placed in a horizontal position on a soft surface being careful not to scratch the crib finish). Install Upper Track Jto the Footboard Vand the
Headboard Xusing two F/H Phillips Wood Screws Aas shown. Attach 4-position Spring Brackets Pusing three Combo Pan Head Wood Screws
Eas shown. Mount Lower Track Assembly Right Fto Footboard V. Start by installing a Combo Pan Head Wood Screw into the holes on Lower
Track Assembly Right F, through the holes in Sta-Bar Bracket - Right O, and into the pilot holes in Footboard Corner Post V. Tighten securely.
Follow the same procedure to attach Lower Track Assembly Left Gand Sta-Bar Bracket Left Nto Headboard Corner Post X. NOTE: Open slot
at top of Lower Track assembly F& Gfaces the inside of your crib. Install hardware exactly as illustrated.
NOTE: All wood screws have factory bored pilot holes to start the screws (pilot holes are shown in diagrams).
(style may vary)
A
E
P
J
PILOTHOLES PILOTHOLES
Closed end of
Upper Track J
SEE ENLARGED VIEW
E
PILOTHOLES
F
O
Slot faces
inside of crib
ENLARGED VIEW
V
V

3
STEP 3-DIAGRAM 3:ATTACH STABILIZING BAR TO HEADBOARD AND FOOTBOARD
STEP 2 - DIAGRAM 2: ATTACH STATIONARY SIDE Attach StationarySide Tto HeadboardXand FootboardV.
Inserteach ofthe four
Allenhead K-D Bolts Hinto receiving holes located in corner posts of Stationary Side
H00745:11/01
Tasshown. PlaceStationary Side Tinalignment andallow K-DBoltsHtocontinue intoends oftopandbottomrails of HeadboardXandFootboard
V. Insert each of the four K-D Bolt Plugs Las shown. Pull out each K-D Bolt Hjust enough to allow the K-D Bolt Plug Lto be fully inserted in hole.
Tighten all four K-D Bolts Huntil secure using Allen Wrench K while securing K-D Bolt Plugs Lwith a Standard Slotted Screwdriver. CAUTION:
DONOTOVERTIGHTEN.
Mount the Stabilizing Bar Assembly Sto
Footboard Vand Headboard X. With the
Footboard Vin a vertical position, insert (2) Phillips Pan Head Machine Screws Dthrough the holes in Sta-Bar Bracket - Right O, and through the
holes in Stabilizing Bar S. Attach (2) Insert Locknuts Ito Machine Screws Dand tighten securely. See Enlarged View for the proper
installation of Locknut I. Follow the same procedure for attaching Stabilizing Bar Sto Headboard X.
X
J
P
N
G
LH
T
L
T
T
H
H
K
L
L
KX
X
Connected View
I
SEE ENLARGED VIEW
ENLARGED VIEW
S
O
FD
V
SD
NorO
Plastic insert on
Lock Nut I

Locate "Tabs" on Crib Spring Yand rotate
Tabs upward to the approximate angle
shown. Lower Spring Yinto crib being
carefulnottodamagethecribfinish. Position
the (4) Tabs attached to ends of Crib Spring
Y to mount to a selected position in the 4-
Position Spring Brackets Pmounted on
endsVandX. Installa HexheadMachine
ScrewBthrough the(4) CribSpring Tabs
and into a receiving hole in each 4-Position
Spring Bracket Pthen tighten securely
with a 3/8” wrench. Follow the same pro-
cedure when changing spring height at a
laterdate.Check HexheadMachineScrews
Bperiodically and tighten if needed.
STEP 4-DIAGRAM 4:INSTALL SPRING
STEP 5 - DIAGRAM 5: INSTALL DROPSIDE
Align Plastic Guides
(Factory installed) on
Dropside Uwith
dropside hardware
mountedon postfrom
underneath. An as-
sistant is very help-
ful. Afterallfour plas-
tic guides are aligned
with the hardware,
liftDropside“UP” and
allow it to latch into
the raised position.
After Dropside Uis
installed on the
tracks and is latched
in the “UP” position,
insert a Combo Ma-
chine Screw Rinto
a Rubber Washer Q
and thread into hole
in bottom of Lower
TrackAssembliesF
&G.
TO LOWER DROPSIDE
U: FIRST - LIFT THE
DROPSIDE, SECOND -
WITH KNEE PUSH IN ON
CENTER OF BOTTOM
RAIL OF DROPSIDE TO
RELEASE LATCH ON
LOWER PLASTIC LATCH.
LOWER DROPSIDE BY
HAND. TO RAISE
DROPSIDE U: PULL
“UP” UNTIL LOWER
PLASTIC GUIDES LATCH
IN SLOT IN LOWER
TRACKSF& G.ALWAYSBE SURECRIBSIDE IS“UP”AND “LATCHED”BEFORELEAVINGCHILDIN CRIB.
4H00745:11/01
Y
P
B
C
Highest mattress position
Lowest mattress position
Corner post of Vor X
Mattress side of Spring Y
NOTE: Mount all four “Tabs” on Crib Spring YY
YY
Y
at the same vertical mattress position.
TAB
U
J
O
F
Align Upper
PlasticGuide
with Upper
Track J
Align Lower
PlasticGuide
with Lower
Track F
LOCKING MECHANISM
NOTE: It may be necessary to Flex the Locking Mechanism toward
outside of crib to engage the Lower Tracks FF
FF
F& GG
GG
G.
Align all four plastic guides with installed
tracks from underneath - then lift “UP” until
Lower Plastic Guides latch.
O
U
F
R
Q
Corner Post of V

5
DIRECTIONS FOR CONVERTING
“CRIB”TO A“DAYBED”
When use as a crib has been completed, by removing the
Dropside, you have the option to convert to a daybed for years of
additional use in your child’s room. Refer to Step 5 - Diagram 5
and follow directions in reverse order. Store the removed parts
and hardware in the event you wish to convert your daybed back
to a crib. Refer to Sketch A.
WHENEVERDISASSEMBLINGYOURCRIB,DONOTREMOVEANY
ITEMS ATTACHED WITH WOOD SCREWS A OR E!
Sketch A
(style may vary)
MAINTENANCE OF YOUR CHILD CRAFT CRIB/DAYBED: Upon completion of assembly be sure all screws, bolts and fastening devices have been
tightened securely. A frequent check should be made of all screws, bolts and fastening devices and tightened if needed. Before each usage or
assembly, inspect crib for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use crib if parts are missing or broken. Contact
your Dealer or Child Craft [phone], for a replacement part or instructional literature if needed. Include Model Identification Number with your
request which you recorded on page 1 of these instructions. DO NOT SUBSTITUTE PARTS. DO NOT MAKE ANY ALTERATIONS NOT DESCRIBED
INTHESE ASSEMBLY DIRECTIONS.
CLEANING INSTRUCTIONS FOR YOUR CHILD CRAFT CRIB/DAYBED: Mix together a mild solution of gentle dishwashing liquid and water, apply to
surface using a soft clean cloth lightly dampened in the solution. Rinse with clear water again using a soft clean cloth, then dry all surfaces thoroughly
with a soft dry cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL, OR COARSE RAGS SHOULD BE USED TO CLEAN THIS FINE
FURNITURE.
STORAGE AND USE OF YOUR CHILD CRAFT CRIB/DAYBED: A printed plastic pouch is attached to the crib spring for the permanent storage of the
assembly directions. After completing the assembly process you are advised to read and be aware of all WARNINGS, CAUTIONS, CLEANING,
STORAGE, USE AND MAINTENANCE notices contained in this set of directions and printed on the plastic pouch located on the underneath side of the
crib spring. You will then place the complete set of assembly directions into the plastic pouch for future referral. We caution you not to place excess
hardware in the plastic pouch as it could present danger to a child if retrieved. When storing crib use CAUTION as extreme temperature or humidity
changes could be harmful. Use CAUTION when a vaporizer is in use, always aim vapor stream away from crib as well as away from any wood
furniture item.
DIRECTIONS FOR CONVERTING
TO AFULL SIZE HEADBOARD
Disassemble crib by performing
Steps 5, 4, 3 & 2 in reverse order to
remove the Stationary Side T from
the other crib parts. Store assembled
parts carefully for future re-assembly
as a Crib. Attach the Stationary Side
toa Hollywoodstylefull size bedframe
at the location of the mounting cleats
(Hardware is not provided). Insert the
Hole Button Covers Mas shown.
H00745:11/01
Receiving holes for
Hole Button Covers M
Receiving holes for
Hole Button Covers M
Mounting Cleats
(Cleats are flush with the face that the
purchased Hollywood Frame mounts to)
T
X
U
V
Purchased Mattress
(see size requirements on
page 6 under CAUTION)
(style may vary)
(style may vary)

6WARNING
ΦΦ
ΦΦ
ΦFAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY IN-
STRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
ΦΦ
ΦΦ
ΦREAD ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP
INSTRUCTIONS FOR FUTURE USE. A PLASTIC POUCH IS ATTACHED TO
CRIBFORPERMANENTSTORAGEOFTHEINSTRUCTIONALLITERATURE.
ΦΦ
ΦΦ
ΦBEFORE EACH USAGE OR ASSEMBLY, INSPECT CRIB FOR
DAMAGED HARDWARE, LOOSE JOINTS, MISSING PARTS OR
SHARP EDGES. DO NOT USE CRIB IF ANY PARTS ARE MISSING
OR BROKEN. ASK YOUR DEALER OR WRITE TO CHILD CRAFT,
P.O. BOX 444, SALEM, IN 47167-0444 USA (812)-883-3111), http://
www.childcraftindustries.com FOR REPLACEMENT PARTS AND
INSTRUCTIONAL LITERATURE IF NEEDED. INCLUDE MODEL IDENTIFI-
CATION NUMBERS WITH YOUR REQUESTWHICHYOURECORDEDON PAGE ONE. DO
NOT SUBSTITUTE PARTS.
ΦΦ
ΦΦ
ΦAFTER RAISING SIDE, MAKE SURE LATCHES ARE SECURE.
ΦΦ
ΦΦ
ΦWHEN CHILD IS ABLE TO CLIMB OUT OR REACHES THE
HEIGHT OF 35 INCHES (90 CENTIMETERS) THE CRIB SHALL NO
LONGER BE USED.
ΦΦ
ΦΦ
ΦDO NOT PLACE CRIB NEAR WINDOW WHERE CORDS FROM
BLINDS OR DRAPES MAY STRANGLE A CHILD.
ΦΦ
ΦΦ
ΦIF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR
CHILDREN’S PRODUCTS.
ΦΦ
ΦΦ
ΦDO NOT LEAVE CHILD IN CRIB WITH SIDE LOWERED. BE SURE
SIDE IS IN RAISED AND LOCKED POSITION WHENEVER CHILD
IS IN CRIB.
ΦΦ
ΦΦ
ΦWHEN CHILD IS ABLE TO PULL TO STANDING POSITION, SET
MATTRESS TO LOWEST POSITION AND REMOVE BUMPER PADS,
LARGE TOYS AND OTHER OBJECTS THAT COULD SERVE AS
STEPS FOR CLIMBING OUT.
ΦΦ
ΦΦ
ΦNEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC
FILM AS MATTRESS COVERS BECAUSE THEY CAN CAUSE SUF-
FOCATION.
ΦΦ
ΦΦ
ΦDO NOT USE A WATER MATTRESS WITH THIS CRIB.
ΦΦ
ΦΦ
ΦREPLACE TEETHING RAIL(S) IF DAMAGED OR LOOSE. (IF
EQUIPPED WITH TEETHING RAILS.)
ΦΦ
ΦΦ
ΦSTRINGS CAN CAUSE STRANGULATION! DO NOT PLACE
ITEMS WITH A STRING AROUND A CHILD’S NECK, SUCH AS
HOOD STRINGS OR PACIFIER CORDS. DO NOT SUSPEND
STRINGS OVER A CRIB OR ATTACH STRINGS TO TOYS.
ΦΦ
ΦΦ
ΦREMOVE ALL CRIB TOYS WHICH ARE STRUNG ACROSS CRIB
AREA WHEN YOUR CHILD IS BEGINNING TO PUSH UP ON HANDS
AND KNEES OR IS 5 MONTHS OF AGE, WHICHEVER OCCURS
EARLIEST. THESE TOYS CAN CAUSE STRANGULATION.
ΦΦ
ΦΦ
ΦWHENDISASSEMBLING THISCRIB, DO NOT REMOVE ANYITEM
ATTACHED WITH WOOD SCREWS.
ΦΦ
ΦΦ
ΦALWAYS ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY
CHECKING REGULARLY, BEFORE PLACING THE CHILD IN THE
CRIB, THAT EVERY COMPONENT IS PROPERLY AND SECURELY
IN PLACE.
CAUTION
ΦΦ
ΦΦ
ΦANY MATTRESS USED IN
THIS CRIB MUST BE AT
LEAST 27-1/4 INCHES (69
CENTIMETERS), BY 51-5/8
INCHES (131 CENTIME-
TERS), WITH A THICKNESS
NOT EXCEEDING 6 INCHES
(15 CENTIMETERS).
THEDIMENSIONSOF THEMATTRESS
SHALL BE TAKEN FROM SEAM TO
SEAMOR EDGETOEDGE WHEREAP-
PROPRIATE.
ΦΦ
ΦΦ
ΦUPON COMPLETION OF
ASSEMBLY BE SURE ALL
SCREWS, BOLTS AND FAS-
TENING DEVICES HAVE
BEEN TIGHTENED SE-
CURELY. A FREQUENT
CHECK SHOULD BE MADE
OF ALL SCREWS, BOLTS
AND FASTENING DEVICES
AND TIGHTEN IF NEEDED.
CHILD CRAFT
INDUSTRIES, INC.
P.O.BOX444
SALEM,IN47167-0444 USA
PH:812-883-3111
FAX:[phone]
http://www.childcraftindustries.com
MADE IN USA
H00745:11/01
H00745:11/01
▲
!