Child Craft LEGACY SINGLE DROPSIDE CRIB WITH DRAWER User manual

SINGLE DROPSIDE CRIB
WITH DRAWER
CONVERTS TO DAYBED
1
CHILD CRAFT INDUSTRIES, INC.
P.O. Box 444, Salem, IN USA 47167-0444
PH:812-883-3111-FAX:[phone]-http://www.childcraftind.com
ASSEMBLY DIRECTIONS AND PARTS LIST
ΦΦ
ΦΦ
ΦREADALLINSTRUCTIONSWITH CAREBEFORE STARTINGTHE ASSEMBLYPROCEDURE.
ΦΦ
ΦΦ
ΦYOU WILL NEED A PHILLIPS SCREWDRIVER, A STANDARD SLOTTED SCREWDRIVER, A 3/8” & 7/16” WRENCH
(or adjustable wrench), AND THE ENCLOSED ALLEN WRENCH KK
KK
K& HEXHEAD WRENCH SS
SS
S.
PARTS ENCLOSED IN HARDWARE BAG ( NOTED WHEN SHOWN ACTUAL SIZE ) DO NOT SUBSTITUTE PARTS!
AB D E
(4) F/HPhillips
Wood Screw
(actual size)
(4) Hexhead
Machine Screw
(actual size)
(4) 4-Position Spring Bracket
FG
(1)
Lower
Track
Assembly
(Right)
(1)
Lower
Track
Assembly
(Left)
HI
J
(4) Allenhead K-D Bolts
(actual size)
(actual size)
(2) Upper Tracks
K
L
M
(actual size)
(4) K-D Bolt Plugs
(actual size)
R
Q
(actual size)
(2) Rubber
Washers
(2) Combo
Machine
Screw
(16) Combo Pan
Head Wood Screw
(4) Insert
Locknut
(4) Casters
(Style may vary)
NO
P(1) Hexhead Wrench
(4) PhillipsPanHead
Machine Screw
(actual size) (actual size)
(1) Sta-Bar Bracket - Right
LH02728:10/00JCHE.p65
S
(1) Allen Wrench
(1) Sta-Bar Bracket - Left
a
b
c
d
e
f
(8)F/HPhillips
Wood Screw
(actual size)
(3) R/HPhillips
Wood Screw
(actual size)
(16) Washers
(actual size)
(2) P/H Slotted
Phillips Wood Screw
(actual size)
(8) F/HPhillips
Wood Screw
(actual size)
(4) Mini Blocks
(actual size)
made
in
usa
20161, 20181, 20191.04,.06,.65

PARTS ENCLOSED IN CARTON
2LH02728:10/00
Y(1) Spring
T(1) Stationary Side
U(1) Drop Side
V(1) Footboard
X(1) Headboard
S(1) Stabilizing Bar (Sta-Bar)
STEP 1-DIAGRAM 1: ATTACH HARDWARE TO FOOTBOARD AND HEADBOARD
(HELPFUL HINT: Hardware installation may be
easier if the Footboard V and Headboard X are
SEE ENLARGED VIEW
gg
gg
g(2) Drawer Rails
hh
hh
h(2) Drawer Ends
ii
ii
i(1) Drawer Partition
jj
jj
j(1) Drawer Front (finished side)
kk
kk
k(1) Drawer Back
ll
ll
l(1) Drawer Bottom
mm
mm
m(1) Drawer Rail-Right
nn
nn
n(1) Drawer Rail-Left
oo
oo
o(1) Drawer "Cabinet Rail"-Right
pp
pp
p(1) Drawer "Cabinet Rail"-Left
PREPARATION Carefully remove and lay out all hardware and parts. Check quantities and match the Hardware List and the Parts
List. NOTE: During the assembly process whenever using screws or bolts, check each with the
Hardware List by letter and size identification. Place each screw or bolt on the diagram of the item which is sketched actual size.
Be sure to use the proper size specified in the assembly directions. If a part is missing or broken contact your Child Craft dealer or Child
Craft, P.O. Box 444, Salem, IN 47167-0444 USA, 812-883-3111, [email protected] for replacement part(s) or instructional literature. Before
making this contact identify your Crib’n’Double Bed by the model identification number stamped on the label on the inside face of the Footboard. Make
note of all identification numbers and include this information with your request. DO NOT SUBSTITUTE PARTS! Record your model identification
number here for future identification: Model #______________________________________
placed in a horizontal position on a soft surface being careful not to scratch the crib finish). Install Upper Track Jto the Footboard Vand the
Headboard Xusing two F/H Phillips Wood Screws Aas shown. Attach 4-position Spring Brackets Pusing three Combo Pan Head Wood Screws
Eas shown. Mount Lower Track Assembly Right Fand Sta-Bar Bracket - Right Oto Footboard V. Start by installing a Combo Pan Head Wood
Screw into the holes on Lower Track Assembly Right F, through the holes in Sta-Bar Bracket - Right O, and into the pilot holes in Footboard Corner
Post V. Tighten securely. Follow the same procedure to attach Lower Track Assembly Left Gand Sta-Bar Bracket Left Nto Headboard Corner Post
X. NOTE: Open slot at top of Lower Track assembly FF
FF
F& GG
GG
Gfaces the inside of your crib. Install hardware exactly as illustrated.
PILOTHOLES
PILOTHOLES
PILOTHOLES
Closed end of
Upper Track J
Slot faces
inside of
crib
NOTE: All wood screws have factory bored pilot
holes to start the screws (pilot holes are
shown in diagrams).
PILOTHOLES
ENLARGED VIEW
V
J
P
P
E
A
E
F
O
E
V

STEP 2- DIAGRAM 2:ATTACH DRAWER RAILS TO FOOTBOARD AND HEADBOARD
LH02728:10/00
Now install Drawer Rail
gg
gg
g and Drawer "Cabi-
net Rail"-Right oo
oo
oto
Footboard VV
VV
V, again ex-
actly as shown using
(4) F/H Phillips/Slotted
Wood Screws aa
aa
a,
tighten securely.
Follow the same proce-
dure for hardware at-
tachmenttoHeadboard
XX
XX
X as directed above.
Install Drawer Rail gg
gg
g
and Drawer "Cabinet
Rail"-Left pp
pp
pusing the
remaining (4) Phillips/
Slotted Wood Screws
aa
aa
a.
NOTE: See Step 7. If the drawer fits too loose in its tracks,
you can adjust the fit by adding the enclosed Washers f .
Install the enclosed Washers f here if needed, between
Drawer Rail g and Footboard V and/or Headboard X.
DO NOT INSTALL WASHERS DURING STEP 2.
a
go
V
Align these three
holes with a
STEP 3 - DIAGRAM 3: ATTACH STABILIZING BAR TO
HEADBOARD AND FOOTBOARD
Mount the Stabilizing Bar Assembly Sto Footboard Vand Headboard X. With
the Footboard Vin a vertical position, insert (2) Phillips Pan Head Machine Screws
Dthrough the holes in Sta-Bar Bracket - Right O, and through the holes in
Stabilizing Bar S. Attach (2) Insert Locknuts Ito Machine Screws Dand tighten
securely. See Enlarged View for the proper installation of Locknut II
II
I.
Follow the same procedure for attaching Stabilizing Bar Sto Headboard X.
SEE ENLARGED VIEW
Plastic insert on
Locknut I
ENLARGED VIEW
I
SO
F
V
I
SNor O
D
D
3
Notepositionof
RollerWheel

4
STEP 4-DIAGRAM 4:ATTACH STATIONARY SIDE
Attach Stationary Side T to
Headboard X& Footboard
V. Insert each of the four
Allenhead K-D Bolts Hinto
receiving holes located in
corner posts of crib ends VV
VV
V
& Xas shown. Place Sta-
tionary Side Tin alignment
and allow K-D Bolts HH
HH
Hto
continue into ends of top and
bottom rails of Stationary
Side T. Insert each of the
four K-D Bolt Plugs LL
LL
Las
shown.Pullouteach K-DBolt
HH
HH
Hjust enough to allow the
K-D Bolt Plug LL
LL
Lto be fully
inserted in hole. Tighten all
four K-D Bolts HH
HH
Huntil se-
cure using Allen Wrench KK
KK
K
whilesecuring K-DBoltPlugs
LL
LL
Lwith a Standard Slotted
Screwdriver. CAUTION: DO
NOTOVERTIGHTEN.
V
H
K
L
T
H
K
L
T
Connected View
LH02728:10/00
Locate "Tabs" on Crib Spring YY
YY
Yand rotate
Tabs upward to the approximate angle
shown. Lower Spring Yinto crib being
carefulnottodamagethecribfinish. Position
the (4) Tabs attached to ends of Crib Spring
YY
YY
Yto mount to a selected position in the 4-
Position Spring Brackets Pmounted on
ends
VV
VV
Vand XX
XX
X. Install a Hexhead Machine
Screw Bthrough the (4) Crib Spring Tabs
and into a receiving hole in each 4-Position
Spring Bracket PP
PP
Pthen tighten securely
using Hexhead Wrench Sor a 3/8” wrench.
Follow the same procedure when changing
springheightatalaterdate.CheckHexhead
Machine Screws BB
BB
Bperiodically and tighten
if needed.
STEP 5-DIAGRAM 5:INSTALL SPRING
Mattress side of Spring Y
Highest mattress position
Lowest mattress position
Tab
Corner Post of Vor X
Y
P
B
S
STEP 6 - DIAGRAM 6:INSTALL DROPSIDE AND CASTERS
Align Plastic Guides
(Factory installed) on
Dropside Uwith
dropside hardware
mountedonpost from
underneath. An as-
sistant is very help-
ful. Afterall four plas-
tic guides are aligned
with the hardware,
liftDropside “UP” and
allow it to latch into
the raised position.
After Dropside U is
installed on the
tracks and is latched
in the “UP” position,
insert a Combo Ma-
chine Screw Rinto
a Rubber Washer Q
and thread into hole
in bottom of Lower
Track Assemblies F
& G.
TO LOWER DROPSIDE UU
UU
U:
FIRST - LIFT THE
DROPSIDE, SECOND -
WITH KNEE PUSH IN ON
CENTER OF BOTTOM
RAIL OF DROPSIDE TO
RELEASE LATCH ON
LOWER PLASTIC LATCH.
LOWER DROPSIDE BY
HAND. TO RAISE
DROPSIDE UU
UU
U: PULL
“UP” UNTIL LOWER
PLASTIC GUIDES LATCH
IN SLOT IN LOWER
TRACKS FF
FF
F& GG
GG
G.
ALWAYSBESURECRIBSIDEIS“UP”AND“LATCHED”BEFORELEAVINGCHILDINCRIB.
Locate the (4) Casters MM
MM
M, insert one into each socket in each
lower corner post of Headboard Xand Footboard V. Caster
design may vary according to your particular model. CAUTION:
If crib is placed on exceptionally thick carpet, take care when crib
is rolled as Casters could catch on thick carpet pile and possibly
cause breakage to lower corner posts of crib.
Align all four plastic guides with installed
tracks from underneath - then lift “UP” until
Lower Plastic Guides Latch.
NOTE: It may be necessary to Flex the Locking Mechanism
toward outside of crib to engage the Lower Tracks F & G .
Align Upper
PlasticGuide
with Upper
Track J
Align Lower
PlasticGuide
with Lower
Track F
LOCKING MECHANISM
J
U
O
F
V
U
R
Q
V
F
NOTE: Mount all 4 “Tabs” on Crib Spring YY
YY
Yat the same vertical mattress position.
O

5
LH02728:10/00
STEP 7-DIAGRAM 7: DRAWER BUILD-UP&INSTALLATION Installation of Mini Blocs ee
ee
e.Refer to Diagrams 7A7A
7A7A
7A, 7B7B
7B7B
7B, 7C7C
7C7C
7C, 7D7D
7D7D
7D,
and 7E7E
7E7E
7E. Install (1) Mini Bloc ee
ee
einto each of the Drawer Ends hh
hh
has shown
NOTE: With the drawer bottom grooves
together - will result in a pair.
Attach Drawer Rail-Left nto Drawer End
hin the same manner as shown for oppo-
site end - NOTE: Both Roller Wheels will go
toward Drawer Back k.
Install extra screws d
at these locations.
d
Install in prebored pilot holes
on both Drawer Ends h.
Roller
Wheel
Insert Drawer Bottom l
intogrooveonall4sides.
Tighten the screw in Mini
Block eto thread into
prebored pilot holes in
Drawer Front j.
Drawer
Bottom
Grooves
Laminated edge
S
ee 7D for
close-up view
7A
S
ee 7B for
close-up view
in Diagram 7A7A
7A7A
7A.NOTE: Before installing the Mini Blocs ee
ee
e, be sure that you have the (2) Drawer Ends hh
hh
haligned exactly as shown in Diagram 7A7A
7A7A
7A
in order to have a pair when complete.
Build Up of the Drawer. Assemble the Drawer as shown in Diagram 7E7E
7E7E
7E. NOTE: After the drawer is assembled as shown in Diagram 7E7E
7E7E
7E,turn
the drawer upside down and install (2) P/H Slotted/Phillips Screws cc
cc
cinto holes located in Drawer Bottom ll
ll
lto secure it to the Drawer Partition ii
ii
i.
Drawer Installation. Install the Drawer under the crib by inserting the rollers on Drawer Rails mm
mm
mand nn
nn
n (attached to the drawer) into the channel
of Drawer “Cabinet Rails” oo
oo
oand pmounted to Headboard XX
XX
Xand Footboard VV
VV
Vunder the crib.
If the drawer fits too loose in its tracks, you can adjust the fit by adding the enclosed washers fas shown in D IAGRAM 2. Remove the drawer. Carefully
lay the crib on its back to allow access to parts aa
aa
a, gg
gg
g, oo
oo
o& pp
pp
p. Remove the Drawer Rails and insert a washer over each screw point aa
aa
abetween
gg
gg
gand VV
VV
Vand/or XX
XX
X. Reinstall rail assembly and drawer. Add additional washers if necessary repeating this process.
Insure the washers are installed between parts
gg
gg
g and
VV
VV
V and/or
XX
XX
X only if needed.
e
h
e
h
Drawer
Bottom
Groove
7B
7C
7D
e
ce
j
h
7E
e
e
h
h
m
j
kb
l
l
i
Laminated edge
Finished Front

6DIRECTIONS FOR CONVERTING
“CRIB”TO A“DAYBED”
When use as a crib has been completed, by removing the
Dropside, you have the option to convert to a daybed for years of
additional use in your child’s room. Refer to Step 6 - Diagram 6
and follow directions in reverse order. Store the removed parts
and hardware in the event you wish to convert your daybed back
to a crib. Refer to Sketch A.
WHENEVERDISASSEMBLINGYOURCRIB,DONOTREMOVEANY
ITEMS ATTACHED WITH WOOD SCREWS AA
AA
AOR EE
EE
E!
Sketch A
(style may vary)
MAINTENANCE OF YOUR CHILD CRAFT CRIB/DAYBED: Upon completion of assembly be sure all screws, bolts and
fasteningdeviceshave beentightened securely. Afrequent checkshouldbe madeofall screws,boltsandfasteningdevices
andtightenedifneeded. Before each usageorassembly,inspectcrib for damagedhardware,loosejoints, missing partsor
sharp edges. DO NOT use crib if parts are missing or broken. Contact your Dealer or Child Craft [phone], for a
replacement part or instructional literature if needed. Include Model Identification Number with your request which you
recorded on page 1 of these instructions. DO NOT SUBSTITUTE PARTS. DO NOT MAKE ANY ALTERATIONS NOT
DESCRIBEDIN THESEASSEMBLYDIRECTIONS.
CLEANINGINSTRUCTIONS FORYOUR CHILDCRAFT CRIB/DAYBED: Mixtogetheramildsolutionof gentledishwashing
liquidandwater,apply tosurfaceusing asoftclean clothlightlydampened inthesolution. Rinse withclearwater againusing
a soft clean cloth, then dry all surfaces thoroughly with a soft dry cloth. NO ABRASIVE CLEANERS, SCOURING PADS,
STEEL WOOL, OR COARSE RAGS SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
STORAGEAND USEOF YOURCHILD CRAFTCRIB/DAYBED: Aprintedplastic pouchis attachedtothecribspring forthe
permanentstorageoftheassembly directions. Aftercompletingthe assemblyprocess youareadvised toread andbeaware
of all WARNINGS, CAUTIONS, CLEANING, STORAGE, USE AND MAINTENANCEnotices contained in this set of direc-
tionsandprinted on theplasticpouch locatedonthe underneath sideofthe cribspring. You willthenplace the completeset
of assembly directions into the plastic pouch for future referral. We caution you not to place excess hardware in the plastic
pouchasit couldpresent dangertoachild ifretrieved. Whenstoring cribuse CAUTION asextreme temperatureorhumidity
changes could be harmful. Use CAUTION when a vaporizer is in use, always aim vapor stream away from crib as well as
awayfromany woodfurnitureitem.
Purchased Mattress
(See size requirements on
page 6 under CAUTION)
V
T
M
U
M
H
X
Purchased Mattress
(See size requirements on
page 6 under CAUTION)
j
i
LH02728:10/00

WARNING
ΦΦ
ΦΦ
ΦFAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY IN-
STRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
ΦΦ
ΦΦ
ΦREAD ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP
INSTRUCTIONS FOR FUTURE USE. A PLASTIC POUCH IS ATTACHED TO
CRIBFORPERMANENTSTORAGEOFTHE INSTRUCTIONALLITERATURE.
ΦΦ
ΦΦ
ΦBEFORE EACH USAGE OR ASSEMBLY, INSPECT CRIB FOR
DAMAGED HARDWARE, LOOSE JOINTS, MISSING PARTS OR
SHARP EDGES. DO NOT USE CRIB IF ANY PARTS ARE MISSING
OR BROKEN. ASK YOUR DEALER OR WRITE TO CHILD CRAFT,
P.O. BOX 444, SALEM, IN 47167-0444 USA (812)-883-3111),
[email protected] FOR REPLACEMENT PARTS AND IN-
STRUCTIONAL LITERATURE IF NEEDED. INCLUDE MODEL IDENTIFICA-
TIONNUMBERSWITH YOURREQUEST WHICHYOURECORDEDONPAGEONE. DONOT
SUBSTITUTE PARTS.
ΦΦ
ΦΦ
ΦAFTER RAISING SIDE, MAKE SURE LATCHES ARE SECURE.
ΦΦ
ΦΦ
ΦWHEN CHILD IS ABLE TO CLIMB OUT OR REACHES THE
HEIGHT OF 35 INCHES (90 CENTIMETERS) THE CRIB SHALL NO
LONGER BE USED.
ΦΦ
ΦΦ
ΦDO NOT PLACE CRIB NEAR WINDOW WHERE CORDS FROM
BLINDS OR DRAPES MAY STRANGLE A CHILD.
ΦΦ
ΦΦ
ΦIF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR
CHILDREN’S PRODUCTS.
ΦΦ
ΦΦ
ΦDO NOT LEAVE CHILD IN CRIB WITH SIDE LOWERED. BE SURE
SIDE IS IN RAISED AND LOCKED POSITION WHENEVER CHILD
IS IN CRIB.
ΦΦ
ΦΦ
ΦWHEN CHILD IS ABLE TO PULL TO STANDING POSITION, SET
MATTRESS TO LOWEST POSITION AND REMOVE BUMPER PADS,
LARGE TOYS AND OTHER OBJECTS THAT COULD SERVE AS
STEPS FOR CLIMBING OUT.
ΦΦ
ΦΦ
ΦNEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC
FILM AS MATTRESS COVERS BECAUSE THEY CAN CAUSE SUF-
FOCATION.
ΦΦ
ΦΦ
ΦDO NOT USE A WATER MATTRESS WITH THIS CRIB.
ΦΦ
ΦΦ
ΦREPLACE TEETHING RAIL(S) IF DAMAGED OR LOOSE. (IF
EQUIPPED WITH TEETHING RAILS.)
ΦΦ
ΦΦ
ΦSTRINGS CAN CAUSE STRANGULATION! DO NOT PLACE
ITEMS WITH A STRING AROUND A CHILD’S NECK, SUCH AS
HOOD STRINGS OR PACIFIER CORDS. DO NOT SUSPEND
STRINGS OVER A CRIB OR ATTACH STRINGS TO TOYS.
ΦΦ
ΦΦ
ΦREMOVE ALL CRIB TOYS WHICH ARE STRUNG ACROSS CRIB
AREA WHEN YOUR CHILD IS BEGINNING TO PUSH UP ON HANDS
AND KNEES OR IS 5 MONTHS OF AGE, WHICHEVER OCCURS
EARLIEST. THESE TOYS CAN CAUSE STRANGULATION.
ΦΦ
ΦΦ
ΦWHENDISASSEMBLING THISCRIB, DO NOT REMOVE ANYITEM
ATTACHED WITH WOOD SCREWS.
ΦΦ
ΦΦ
ΦALWAYS ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY
CHECKING REGULARLY, BEFORE PLACING THE CHILD IN THE
CRIB, THAT EVERY COMPONENT IS PROPERLY AND SECURELY
IN PLACE.
7
CAUTION
ΦΦ
ΦΦ
ΦANY MATTRESS USED IN
THIS CRIB MUST BE AT
LEAST 27-1/4 INCHES (69
CENTIMETERS), BY 51-5/8
INCHES (131 CENTIME-
TERS), WITH A THICKNESS
NOT EXCEEDING 6 INCHES
(15 CENTIMETERS). THE
DIMENTIONS OF THE MATTRESS
SHALL BE TAKEN FROM SEAM TO
SEAMOREDGETOEDGEWHEREAP-
PROPRIATE.
ΦΦ
ΦΦ
ΦUPON COMPLETION OF
ASSEMBLY BE SURE ALL
SCREWS, BOLTS AND FAS-
TENING DEVICES HAVE
BEEN TIGHTENED SE-
CURELY. A FREQUENT
CHECK SHOULD BE MADE
OF ALL SCREWS, BOLTS
AND FASTENING DEVICES
AND TIGHTEN IF NEEDED.
CHILD CRAFT
INDUSTRIES, INC.
P.O. BOX 444
SALEM,IN47167-0444 USA
PH:812-883-3111
FAX:[phone]
http://www.childcraftind.com
MADE IN USA
LH02728:10/00JCHE.p65
▲
!
LH02728:10/00