Chore-Time E-Z User manual

36” & 48” E-Z Box Fan
Installation & Operator’s Instruction Manual
(Direct Drive · Standard & Deep Box)
MV1430GAugust 2009

2
Chore-Time 36” & 48” Direct Drive E-Z Box Fan Manual
Chore-Time Warranty
Chore-Time Egg Production Systems, a division of CTB, Inc., (“Chore-Time”), warrants each new
CHORE-TIME® product manufactured by it to be free from defects in material or workmanship for one
(1) year from and after the date of initial installation by or for the original purchaser. If such a defect is
found by Chore-Time to exist within the one-year period, Chore-Time will, at its option, (a) repair or
replace such product free of charge, F.O.B. the factory of manufacture, or (b) refund to the original
purchaser the original purchase price, in lieu of such repair or replacement. Labor costs associated with
the replacement or repair of the product are not covered by the Manufacturer.
Conditions and Limitations
1.The product must be installed by and operated in accordance with the instructions published by the
Manufacturer or Warranty will be void.
2.Warranty is void if all components of the system are not original equipment supplied by the
Manufacturer.
3.This product must be purchased from and installed by an authorized distributor or certified
representative thereof or the Warranty will be void.
4."Malfunctions or failure resulting from misuse, abuse, mismanagement, negligence, alteration,
accident, or lack of proper maintenance, or from lightning strikes, electrical power surges or
interruption of electricity shall not be considered defects under the Warranty. Corrosion, material
deterioration and/or equipment malfunction caused by or consistent with excessive additions or
application of chemicals, minerals, sediments or other foreign elements with the product shall not be
considered defects under the Warranty."
5.This Warranty applies only to systems for the care of poultry and livestock. Other applications in
industry or commerce are not covered by this Warranty.
Chore-Time shall not be liable for any Consequential or Special Damage which any purchaser may
suffer or claim to suffer as a result of any defect in the product. “Consequential” or “Special
Damages” as used herein include, but are not limited to, lost or damaged products or goods, costs of
transportation, lost sales, lost orders, lost income, increased overhead, labor and incidental costs and
operational inefficiencies.
THIS WARRANTY CONSTITUTES THE MANUFACTURER’S ENTIRE AND SOLE WARRANTY AND
THIS MANUFACTURER DISCLAIMS ANY AND ALL OTHER WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, EXPRESS AND IMPLIED WARRANTIES AS TO MERCHANTABILITY, FITNESS FOR
PARTICULAR PURPOSES SOLD AND DESCRIPTION OR QUALITY OF THE PRODUCT FURNISHED
HEREUNDER.
Chore-Time Distributors are not authorized to modify or extend the terms and conditions of this
Warranty in any manner or to offer or grant any other warranties for CHORE-TIME® products in
addition to those terms expressly stated above. An officer of CTB, Inc. must authorize any exceptions
to this Warranty in writing. Chore-Time reserves the right to change models and specifications at any
time without notice or obligation to improve previous models.
CTB Inc.
P.O. Box 2000 • Milford, Indiana 46542-2000 • U.S.A.
Phone [phone] • Fax [phone]
E-Mail: [e-mail] • Internet: http//www.ctbinc.com
Printed in the U.S.A.

Table of Contents
Topic Page User*
*Legend: C = Customer (end user), D = Distributor (sales), I - Installer of equipment
Chore-Time Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 C, D
Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C, D
Distributor and Installer Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 C, D, I
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 C, I
Safety–Alert Symbol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 C, I
Signal Words. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 C, I
DANGER: Electrical Hazard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 C, I
Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 C, I
E-Z Fan Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 C, I
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 C, I
Fan Assembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 I
Slant Wall Kit Assembly (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 I
Fan Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 I
Side Wall Installations: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 I
Fan Assembly without Slant Wall Housing:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 I
Fan Assembly with Slant Wall Housing: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 I
Suspended Fan Installations: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 I
Wiring: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 I
Shutter Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 I
Maintenance:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 C
Direct Drive E-Z Fan Part Numbers and Motor Specifications. . . . . . . . . . . . . . . 18 C, I
Direct Drive E-Z Fan Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 C, I

4
Chore-Time 36” & 48” Direct Drive E-Z Box Fan Manual
Support Information
The Chore-Time E-Z Fans are designed to be used as circulating or exhaust fans. The E-Z Fans may be
shipped unassembled to save on shipping charges. Using this equipment for any other purpose or in a way
not within the operating recommendations specified in this manual will void the warranty and may cause
personal injury.
This manual is designed to provide comprehensive planning, installation, operation, and parts listing
information. The Table of Contents provides a convenient overview of the information in this manual. The
Table of Contents also specifies which pages contain information for the sales personnel, installer, and
consumer (end user).
IMPORTANT: CE stands for certified Europe. It is a standard which
equipment must meet or exceed in ordered to be sold in Europe. CE
provides a benchmark for safety and manufacturing issues. CE is
required only on equipment sold in Europe.
Chore-Time Equipment recognizes CE Mark and pursues compliance
in all applicable products. Fill in the CE-Mark serial number in the
blank space provided for future reference.
(CE-mark serial number)
Distributor and Installer Information
Please fill in the following information about your Product.
Keep this manual in a clean, dry place for future reference.
Distributor’s Name ___________________________________________________
Distributor’s Address ________________________________________________
Distributor’s Phone _______________________ Date of Purchase ___________
Installer’s Name _____________________________________________________
Installer’s Address ___________________________________________________
Installer’s Phone _______________________ Date of Installation ___________
System Specifications ________________________________________________
___________________________________________________________________

Chore-Time 36” & 48” Direct Drive E-Z Box Fan Manual
5
Safety Information
Caution, Warning and Danger Decals have been placed on the equipment to warn of potentially
dangerous situations. Care should be taken to keep this information intact and easy to read at all times.
Replace missing or damaged safety signs.
Using the equipment for purposes other than specified in this manual may cause personal injury and or
damage to the equipment.
Safety–Alert Symbol
This is a safety–alert symbol. When you see this symbol on your equipment, be alert to
the potential for personal injury. This equipment is designed to be installed and operated
as safely as possible...however, hazards do exist.
Signal Words
Signal words are used in conjunction with the safety–alert symbol to
identify the severity of the warning.
DANGER........... indicates an imminently hazardous situation
which, if not avoided, WILL result in death
or serious injury.
WARNING........ indicates a potentially hazardous situation
which, if not avoided, COULD result in
death or serious injury.
CAUTION.......... indicates a hazardous situation which, if not
avoided, MAY result in minor or moderate
injury.
DANGER: Electrical Hazard
Disconnect electrical power before inspecting or servicing
equipment unless maintenance instructions specifically state
otherwise.
Ground all electrical equipment for safety.
All electrical wiring must be done by a qualified electrician in
accordance with local and national electric codes.
Ground all non-current carrying metal parts to guard against
electrical shock.
With the exception of motor overload protection, electrical
disconnects and over current protection are not supplied with the
equipment.
DANGER
WARNING
CAUTION

Chore-Time 36” & 48” Direct Drive E-Z Box Fan Manual
6
This diagram shows the proper location of the safety decal (DANGER--
ROTATING FAN BLADE) as shipped from the factory. Replace damaged or
missing decals. Make sure the decals may be easily seen at all times.
If the fan is purchased unassembled, the Chore-Time Fan Assembly Part Number
Decal will be packed with this instruction manual. Make sure the decal location
shown below is clean and dry. Remove the backing of the decal and affix it to the
Fan Shroud.
Technical Information
Motor choices and specifications are provided in the Parts List section of this
manual. See page 14 for Fan Motor specifications.
Important
Chore-Time Equipment strongly recommends that a good alarm system should be
installed in confinement buildings to warn of power failure and high temperature.
Chore-Time Equipment also recommends that an alternate power source be
available for confinement buildings in case of power failure.
E-Z Fan Options
The E-Z Fan may be ordered assembled or unassembled (knock-down).
If the Fan is to be suspended from the ceiling, the Slant Wall Kit is not used. If the
Fan is to be installed in a side wall, the Slant Wall Kit may be used.
There are a variety of Motors available for the E-Z Fans. See the motor
specifications chart in the parts list section of this manual.
The E-Z Fans may be ordered with standard width Side Panels or Deep Box Side
Panels. The standard width Side Panels are 12-1/2” (31.8 cm) or 15-3/4” (40.0
cm), respectively, for the 36” and 48” Fans. The Deep Box Side Panels are 21”
(53.3 cm) wide.

Chore-Time 36” & 48” Direct Drive E-Z Box Fan Manual
7
Tools Required
• Regular Screwdriver
•Hammer
• 1/2” Open End Wrench or Socket Wrench with 1/2” Socket
• Wire Cutters & Strippers
• Adequate Size & Quantity of Electrical Wire
• 5/16” Hex Key Wrench
• 5/16” Open End Wrench or a 12 Point 3/8” Socket and Ratchet
Fan Assembly Procedure
Installation Note: Many of the graphics provided reflect the standard Side Panels.
Side Panels for the Deep Box Fans look similar, only wider.
Secure the Motor Mount Post to the Fan Shroud using the 5/16-18 x 5/8” carriage
bolts and hex nuts provided in the Hardware Package
The Motor Mount Post must be installed as shown in Figure 1.
Secure the Motor Support, as shown in Figure 1.
Figure 1. Motor Mount Installation (side view)
Key Description
1FanShroud
2 Motor Mount Post
3 5/16-18 x 5/8” Carriage Bolt
4 5/16-18 Hex Nut
5 Lock Washer
6 Motor Support Plate

Chore-Time 36” & 48” Direct Drive E-Z Box Fan Manual
8
The Side Panels for the Box Fans are identical. The Panels lock together by
inserting the tabs of one Panel into the slot in the end of another Panel. See the
detail in Figure 2.
Orienting the Side Panels as shown in Figure 2, assemble the Side Panels together
around the Shroud using the 5/16-18 hardware provided.
Note: 36” Fans use (2) bolts, washers, and nuts per side. 48” Fans use (3) bolts,
washers, and nuts per side.
Use a hammer to carefully bend the corner tabs over to secure the Side Panels
together.
Orient the Shroud with the Shroud Drain Holes at the bottom of the Fan.
Figure 2. Side Panel Assembly (top view)
Secure the Motor to the Motor Support. Fan Motors with capacitors, orient as
shown in Figure 3 and Figure 4.
The 36” Fans use 10-32 Serrated Flange Nuts provided in the Hardware
Package. Figure 3.
The 48” Fans use lock washers and 3/8” x 3/4” bolts provided in the Hardware
Package. See Figure 4.
Key Description
1 Side Panel
2FanShroud
3 5/16-18 x 5/8” Carriage Bolt
4 5/16-18 Hex Nut
5 Lock Washer
6 Lock Side Panels together by
bending tabs over.
7 Shroud Drain Holes
8 Shroud Orifice
9 Shroud Knockouts

Chore-Time 36” & 48” Direct Drive E-Z Box Fan Manual
9
Figure 3. Motor Installation (side view)
Figure 4. Motor Installation (side view)
Slide the Blade Assembly onto the motor shaft. The Fan Blade Hub should be
flush to the end of the motor shaft. See Figure 5.
Key Description
1 Motor Support
2Motor
3 10-32 Serrated Flange Nut
Key Description
1 Motor Support
2 Motor
3 3/8” x 3/4” Bolt
4 Lock Washer
MV1430-050 2/04
21
3
48”
F
an

Chore-Time 36” & 48” Direct Drive E-Z Box Fan Manual
10
Insert key into keyway on motor shaft.
Tighten the set screw(s) using a 5/16” open end wrench (12 point 3/8” socket and
ratchet). Torque the set screws to approximately 150 in./lbs.
See the decal placement instructions on page 4.
Figure 5. Blade Assembly Installation (side view)
Key Description
1 Blade Assembly
2 Fan Blade Hub
3 Motor
4 Motor Shaft with key/keyway
and flat

Chore-Time 36” & 48” Direct Drive E-Z Box Fan Manual
11
DANGER: Wire Screen(s) MUST be installed to prevent serious injury or
death.
Position the front Screen over the front of the fan.
Note: Make sure the natural bow of the Screen is away from the fan (to avoid
blade interference).
Install (4) Wire Clips on each side to secure the Screen to the Panels. See Figure 6.
Box Fan Installations: The rear Screen is cut out to accommodate the motor.
Position the rear Screen over the back of the fan. Install (4) Wire Clips on each
side to secure the Screen to the Panels. See Figure 6.
Slant Wall Fan Installations: The Shutter will be used in place of the Rear
Screen.
Note: A Rear Screen is not included with a Slant Wall Fan.
Figure 6. Screen Installation
Key Description
1 Screen Clip
2WireScreen
3 Slip Screen Clip over Screen
Wire. Snap in slot on Fan Side
Panel to secure.

Chore-Time 36” & 48” Direct Drive E-Z Box Fan Manual
12
Slant Wall Kit Assembly (Optional)
If the Fan Assembly is to be installed in a side wall, the E-Z Fan Slant Wall
Housing Kit may be assembled and installed.
Refer to Figure 7 for assembly information.
1. Lay assembled fan on work surface (with the motor end up).
2. Set the Slant Wall Bottom Panel in place on the Fan Assembly. Secure the
Bottom Panel to the Fan Assembly by inserting the tabs into the bridges, as
shown in the detail in Figure 7.
3. Set the Slant Wall Side Panels in place on the Fan Assembly. The Slant Wall
Side Panels are also secured to the Fan Assembly by inserting the tabs into the
bridges, as shown in the detail in Figure 7.
4. Set the Slant Wall Top Panel in place on the Fan Assembly. Secure the Top
Panel to the Fan Assembly by inserting the tabs into the bridges, as shown in
the detail in Figure 7.
5. The Slant Wall Panels are designed to lock together similar to the Box Fan
Panels. Use a hammer to carefully bend the corner tabs over to secure the Slant
Wall Panels together.
Figure 7. Slant Wall Housing Assembly (side view)
Lock the Slant Wall Kit on the Box Fan by bending the tabs in the Slant Wall
Panels into the bridges of the Box Fan Panels as shown in Figure 8.
Key Description
1 Bottom of Fan Assembly
2 Top of Fan Assembly
3 Fan Side Panel
4 Slant Wall Housing Top Panel
5 Slant Wall Housing Bottom Panel
6 Slant Wall Housing Side Panel

Chore-Time 36” & 48” Direct Drive E-Z Box Fan Manual
13
Figure 8. Slant Wall Lock Tab
Fan Installation
The E-Z Fan may be installed in a wall or suspended from the ceiling. For
installations with the fan suspended from the ceiling, refer to Figure 12.
Side Wall Installations:
Build fan framing out of 2” (50 mm) lumber (not supplied). The required wall
opening is provided in the chart below. See Figure 9.
Allow a minimum 4” spacing between framed openings for adjacent Slant Wall
Fans to allow clearance for the Slant Wall Fans 2” mounting flange.
Figure 9. Framing Diagram (front view)
Fan Assembly without Slant Wall Housing:
Insert the Fan Assembly in the framed opening in the side wall. If an Aluminum
Shutter is to be installed, the fan must be recessed in from the outside edge of the
framed opening approximately 1/2” (13 mm). Secure the Fan Assembly and
Shutter to the framed opening (hardware not supplied).
Make sure the Shutter can open and close freely.
Key Description
1 Screwdriver
2 Box Fan Panel
3 Slant Wall Panel
Dimension
(minimum)
A B
36” Box Fan
& Panel Fan
42-1/4”
(107.3 cm)
42-1/4”
(107.3 cm)
36” Box Fan
w/Slant Wall Kit
43”
(109.2 cm)
43”
(109.2 cm)
48” Box Fan
& Panel Fan
54-5/8”
(138.7 cm)
54-5/8”
(138.7 cm)
48” Box Fan
w/Slant Wall Kit
55”
(139.7 cm)
55”
(139.7 cm)

14
Chore-Time 36” & 48” Direct Drive E-Z Box Fan Manual
Fan Assembly with Slant Wall Housing:
Insert the Fan Assembly and Slant Wall Housing through the framed opening in the side wall.
Center the Slant Wall Housing in the framed opening, left to right. Allow the Slant Wall Housing
to set on the bottom of the framed opening.
Secure the Slant Wall Housing to the framed opening, using (1) 1/4” x 1-3/4” Lag Screw through
the middle hole on each side and (3) 1/4” x 1-3/4” Lag Screws across the bottom panel. See
Figure 10. Lag Screws are supplied in the Hardware Package.
Figure 10. Fan installation (side view)
Install the Shutter Clips, as shown in Figure 11, in the remaining holes on the sides and top of the
Slant Wall Kit. The Shutter Clips need to be tight, but loose enough to be turned.
Figure 11. Shutter Clip installation (front view)
Key Description
1 Fan and Slant Wall Housing Assembly
2 Side Wall of Building
3 1/4” x 1-3/4” Lag Screws (5 used)
Key Description
1 Slant Wall Housing
2 1/4 x 1-3/4” Lag Screw
3 Shutter Clip
4 Nylon Flat Washer

Chore-Time 36” & 48” Direct Drive E-Z Box Fan Manual
15
Suspended Fan Installations:
Replace Items 9 - 11 from both sides of the top of the fan with the suspension
components, Items 1 - 7, as shown in Figure 12. Discard Items 9 - 11.
The 36” E-Z Fan Assembly weighs approximately 120 lbs. (43.1 kg). The ceiling,
rafters, or trusses must be capable of bearing the required weight.
The 48” E-Z Fan Assembly weighs approximately 175 lbs. (70.3 kg). The ceiling,
rafters, or trusses must be capable of bearing the required weight.
Figure 12. Suspending the Fan (front view)
Key Description Key Description
1 Screw Hook 7 Hex Nut
2 S-Hook 8 E-Z Box Fan
3 Chain 9 5/16-18 Carriage Bolt
4EyeBolt 10FlatWasher
5 Flat Washer 11 Hex Nut
6 Lock Washer

Chore-Time 36” & 48” Direct Drive E-Z Box Fan Manual
16
Wiring:
See wiring diagram on Motor for Motor electrical connections. Follow local, state
and national electric codes for wiring.
Install an electric disconnect within reach of each Fan.
Slant Wall Fans: Route the motor cord (not supplied) toward the upper left corner
of fan and attach the cord to the top panel using the 3/8” cord clip mounted in the
1/4” hole in the top panel. See Figure 13.
Important: If an Aluminum Shutter will be installed, route the motor cord
through the Rubber Grommet.
Some installations may require an exit hole for the motor cord be drilled in the side
of the Shroud. These installations must have electrical wires routed through
conduit to protect them from damage.
Note: Make sure the conduit or wires do not interfere with the Fan Blades or
Shutter operation.
Figure 13. Installing Cord Clip.
Key Description
1 Slant Wall Top Panel
2CordClip
3 Cord

Chore-Time 36” & 48” Direct Drive E-Z Box Fan Manual
17
Shutter Installation
Install the Grommet in the corner of the Aluminum Shutter only. See Figure 14.
For fans with plastic shutters, cut a 3/8” slot in the left end of the top flange of the
shutter to route the cord through when the shutter is installed. See detail in Figure
14.
The Slant Wall Bottom Panel is designed to hold the Shutter. Slide the bottom of
the Shutter into position in the Bottom Panel of the Slant Wall kit, lean the Shutter
back and lock it in place by rotating the Shutter Clips. See Figure 14.
Figure 14. Shutter Installation (front view)
Maintenance:
IMPORTANT! Disconnect Power Prior To Maintaining Or Cleaning The Fan.
The fan may start automatically causing serious injury or death.
• Service and repair of fans should be done only by a qualified technician.
•Minimize contact of moisture or corrosive chemicals to the surfaces of the fan
components to maximize fan life.
•After washing fans, operate fans long enough to remove moisture from all fan
surfaces.
• Keep the fan clean for maximum life and best performance.
Key Description
1 Grommet (Aluminum Shutter Only)
2 Shutter
3 Shutter Clip
4 Slant Wall Housing
5 3/8” Slot in Plastic Shutter

18
Chore-Time 36” & 48” Direct Drive E-Z Box Fan Manual
Direct Drive E-Z Fan Part Numbers and Motor
Specifications
Direct Drive E-Z Box Fans
Fan Description
Assembled
Fans
Unassembled
Fans
Electrical Specs.
Fan P/N + Fan P/N + Voltage HZ Phase HP Motor P/N
36” Direct
Drive
E-Z Fans
Box
37124-3610
37124-3620
37124-3640
37124-3680
37125-3610
37125-3620
37125-3640
37125-3680
115
208-230
208-230/460
115/230
60
60
60
60
1
1
3
1
1/2
1/2
1/2
1/2
27536
28936
27536-3PH
48614
Deep
Box
38109-3610
38109-3620
38109-3640
N/A
38110-3620
38110-3640
115
208-230
208-230/460
60
60
60
1
1
3
1/2
1/2
1/2
27536
28936
27536-3PH
Slant
Wall
38789-361X
38789-362X
38789-364X
38796-361X
38796-362X
38796-364X
115
208-230
208-230/460
60
60
60
1
1
3
1/2
1/2
1/2
27536
28936
27536-3PH
Deep
Slant
Wall
N/A
N/A
38797-362X
38797-364X
208-230
208-230/460
60
60
1
3
1/2
1/2
28936
27536-3PH
Panel
40404-3610
40404-3620
40404-3640
N/A
40411-3620
N/A
115
208-230
208-230/460
60
60
60
1
1
3
1/2
1/2
1/2
27536
28936
27536-3PH
48”
Direct Drive
E-Z Fans
Box 38439-4820
38439-4840
38782-4820
38782-4840
230
460
60
60
1
3
1
1
37726
39020
Slant
Wall
38785-482X
38785-484X
38792-482X
38792-484X
230
460
60
60
1
3
1
1
37726
39020
+ Replace “X” in fan P/N with “1” for an aluminum shutter, or “2” for a plastic shutter
-slant wall fans include a box fan, slant wall kit, and shutter

Chore-Time 36” & 48” Direct Drive E-Z Box Fan Manual
19
Direct Drive E-Z Fan Parts List
36”
F
ans
* These items included in 36” Slant Wall Kit Part Number 39018.
Item Description Part No.
1 36” Fan Shroud 5538
2 Motor Mount Post 37209
3 36” Fan Panel (12-1/2” Deep)
36” Fan Panel (21” Deep)
36006
37556
4 Wire Screen 29046
5 Motor Support 36564
6 36” 3 Wing Fan Blade 40358
7 Screen Clip 38891
8 Danger Decal 2527-50
9 Wire Inlet Screen 36629
10 Motor See Chart
11* 36” S. W. L.H. Side Panel 39013-1
12* 36” S. W. Top Panel 39011
13* 36” S. W. Bottom Panel 39012
14* 36” S. W. R.H. Side Panel 39013-2
15 36” Aluminum Shutter
36” Plastic Shutter
38259
38027
16* 1/4 x 1-3/4 Lag Screw 39217
17* Shutter Clip 36729
18* Nylon Washer 4856
19* Grommet 7256
20* Cord Clip 7242
21 Nut, 10-32 Serrated Flange 48113
22 Not used on 36” Fan --
48” Fans
* These items included in 48” Slant Wall Kit Part Number 38446.
Item Description Part No.
1 48” Fan Shroud 37583
2 Motor Mount Post 38390
3 48” Fan Panel (15-3/4” deep)
48” Fan Panel (21” deep)
38391
38438
4 Wire Screen 6023-22
5 Motor Support 37941
6 48” 2 Wing Fan Blade 37727
7 Screen Clip 38891
8 Danger Decal 2527-50
9 Wire Inlet Screen 38749
10 Motor See Chart
11* 48” S. W. L.H. Side Panel 38449-1
12* 48” S. W. Top Panel 38447
13* 48” S. W. Bottom Panel 38448
14* 48” S. W. R.H. Side Panel 38449-2
15 48” Aluminum Shutter
48” Plastic Shutter
38260
38029
16* 1/4 x 1-3/4 Lag Screw 39217
17* Shutter Clip 36729
18* Nylon Washer 4856
19* Grommet 7256
20* Cord Clip 7242
21 3/8-16 x 3/4 Hex Bolt 2182
22 3/8 Lock Washer 5747

Made to work.
Built to last.
Note: The original, authoritative version of this manual is the [English] version produced
by CTB, Inc. or any of its subsidiaries or divisions, (hereafter collectively referred to as
"CTB"). Subsequent changes to any manual made by any third party have not been
reviewed nor authenticated by CTB. Such changes may include, but are not limited to,
translation into languages other than [English], and additions to or deletions from the
original content. CTB disclaims responsibility for any and all damages, injuries, warranty
claims and/or any other claims associated with such changes, inasmuch as such changes
result in content that is different from the authoritative CTB-published [English] version of
the manual. For current product installation and operation information, please contact the
customer service and/or technical service departments of the appropriate CTB subsidiary
or division. Should you observe any questionable content in any manual, please notify CTB
immediately in writing to: CTB Legal Department, P.O. Box 2000, Milford, IN 46542-
2000 USA.
Revisions to this Manual
Page No. Description of Change
Various Updated Warranty page, Changed Area Code, Added Third Party paragraph.
Contact your nearby Chore-Time distributor or representative for additional parts and information.
CTB, Inc.
P.O. Box 2000
Milford, Indiana 46542-2000 U.S.A.
Phone: [phone] • E-Mail: [email protected]
Printed in the U.S.A