Vectaire ELP2204 User manual

• 4 speed cont nuous runn ng
• cord or remote
• for all domest c wet rooms
• for walls or ce l ngs
IPX4
ELP2204
H gh Performance Centr fugal Fan
Installat on and Operat ng Instruct ons

The pr duct y u have purchased is an extract r fan f r exhausting
directly utside r thr ugh l nger lengths f ducting (up t 15m) and
is suitable f r wall r ceiling installati n. T ensure ptimum pera-
ti n and guarantee a l ng life, please read this manual carefully. It
explains h w t install c rrectly, use and maintain the pr duct pr p-
erly. F ll wing these instructi ns will ensure the reliability f the pr d-
uct and extend its w rking life.
The manufacturer w ll not accept any respons b l ty for damage
caused to persons or th ngs due to mproper use w th reference
to the precaut ons outl ned n th s leaflet.
The pr duct, c nstructed using state f the art techn l gy, c mplies
with current standards regarding electrical equipment. It c nf rms
with EN 60335-2-80, B.T. 2006/95/CE, EMC 2004/108/CE.the
EMC 2004/108/EC Eur pean Directive regarding radi interfer-
ence suppressi n and electr -magnetic c mpatibility.
WARNING: Ser ous njury or death could result f these nstruct ons are
not carefully followed
• D n t use this pr duct f r any purp se ther than that f r which
it was designed.
• Rem ve the pr duct fr m its packaging and make sure that it
has n t been damaged. If in d ubt, c ntact the supplier, auth -
rised dealer, service centre r manufacturer t check that the
pr duct will still perate c rrectly. D n t attempt t use r re-
pair the pr duct bef re d ing this.
• D n t leave packing material within the reach f children r un-
skilled pe ple. T disp se f the packaging and the appliance at
the end f its useful life refer t the recycling rules in f rce.
• The use f any electrical pr duct requires c mpliance with s me
basic rules which are listed bel w:
- d n t t uch it with wet r damp parts f the b dy (e.g hands,
feet).
- this pr duct is n t intended f r use by pers ns (including chil-
dren) with reduced physical, sens ry r mental capabilities r
lack f experience and kn wledge, unless they have been given
supervisi n r instructi n c ncerning the use f the pr duct
by a pers n resp nsible f r their safety. The fan sh uld be
sited where it is inaccessible t such pe ple.
- children sh uld be supervised t ensure they d n t play with
the pr duct.
• The pr duct sh uld be c nnected t the mains electricity supply
r electrical utlet nly if:
- the electrical v ltage and frequency c rresp nd t th se
sh wn n the rating label.
- the capacity f the electricity supply is sufficient t perate the
pr duct at its maximum p wer.
- suitable electrical pr tecti n is pr vided f r the pr duct t be
installed.
• The electrical supply t which the fan is c nnected must c mply
with all existing regulati ns. All installati ns must c mply with
current IEE wiring regulati ns.
• Bef re maintenance r cleaning is carried ut, the pr duct must
be switched ff and disc nnected fr m the mains electricity sup-
ply.
• If a fault, malfuncti n r an maly f any type ccurs, the fan sh uld
be is lated (switching it ff and disc nnecting it fr m the mains
electricity supply) and advice s ught fr m qualified pers nnel.
• Always request riginal spare parts f r repairs
• If the pr duct needs t be rem ved, turn ff the mains supply
and then disc nnect the fan.
• The fan MUST BE installed as detailed in this leaflet
WARNING: Damage could be caused to the product f the nstal-
lat on nstruct ons are not followed
• The pr duct sh uld not be used in an ambient temperature
higher than 40°C (104°F).
• The pr duct sh uld not be exp sed t atm spheric agents (rain,
sun, sn w, etc.).
• The pr duct r its parts sh uld not be placed in water r ther
liquids.
• R utine maintenance as described sh uld be carried ut t
check the c nditi n f the fan.
• The air r fumes being extracted must be clean and free fr m
greasy particles, s t, chemical and c rr sive agents, flamma-
ble r expl sive mixtures.
• The product must be nstalled by profess onally qual f ed per-
sonnel. Incorrect nstallat on can cause damage to people,
an mals or property, for wh ch the manufacturer cannot be
held l able.
• The pr duct must be c nnected t the electricity supply via a
d uble p le switch f a suitable size, with c ntact penings f at
least 3 mm.
• If the electrical supply b ard ( r switching device) is l cated
s me distance fr m the fan a means f l cal is lati n must be
pr vided.
• T ensure ptimum perati n, d n t bl ck the air intake and
exit vents.
• Any ducting used must be free f bl ckages, and sh uld be insu-
lated if in an unheated area.
• The r m where the pr duct is perating must have adequate
air replacement t ensure maximum effectiveness.
• If the pr duct is sited in a r m c ntaining a fuel burning appli-
ance which is n t f the balanced flue type, the installer must en-
sure that air replacement is adequate b th f r the fan and the
fuel burning appliance (UNI CIG 7129).
• The pr duct must not be used as an activat r f r water
heaters, st ves, etc.
• The pr duct must not exhaust int ducts designed t evacuate
fumes fr m c mbusti n in st ves r ther c mbusti n-p wered
devices.
RANGE
Speed 1 - 13 l/sec - 47 m³/hr
Speed 2 - 30 l/sec - 108 m³/hr
Speed 3 - 45 l/sec - 162 m³/hr
Speed 4 - 60 l/sec - 216 m³/hr
ELP2204 - this fan c mbines the latest techn l gy with energy
saving and efficiency. It is a 4 speed centrifugal fan. It is designed
t run c ntinu usly at a Speed 1 with three pti ns f r a pre-selec-
table b st speed (Speed 2, Speed 3 r Speed 4), which is fixed at
installati n. The user can b st the fan speed t its maximum per-
f rmance when required by means f the c rd r rem ve the c rd
and use a rem te switch, light switch, PIR sens r r humidistat. If
the fan s to be ce l ng mounted, the pull-cord sw tch should be
put n the “off” pos t on and the cord removed. A remote sw tch
w ll be necessary for chang ng the fan speed. See w r ng d a-
grams, page 4.
ELP2204” - HIGH PERFORMANCE CENTRIFUGAL FANS
INSTALLATION and OPERATING INSTRUCTIONS
THIS LEAFLET MUST BE AVAILABLE TO THE USER
Page 2

INSTALLATION
12
45
3
6
78
910
12
11
14
13
1. Check there is n thing missing in b x and
dismantle fan
2. Drill h le in wall - allow extra w dth f us ng
duct ng - t s the nstaller's respons b l ty
to use the appropr ate core cutter to ob-
ta n the correct hole d ameter.
3. Use fan casing as template t mark drill
h les.
4. Drill 4 x 6mm dia h les.
5. Fit wall plugs.
6. Rem ve b ard c ver.
7/8 Decide whether t have cable access fr m
rear r t p f fan - if fr m t p ensure that
included gr mmet is pr perly fixed. (See
dia 8). If cable is t c me thr ugh rear f
fan, fit rubber ring (included) .
9. Screw fan casing t wall
10. Fit and c nnect m t r fan assembly.
11. C nnect cable using cable clamp - SEE
WIRING DIAs for spec f c use.
NB th s fan s double nsulated and does not
need to be earthed
12. Before replac ng c rcu t board cover
choose the boost speed for the fan.n
SEE JUMPER SWITCH SETTINGS BELOW
13. P siti n fr nt c ver.
14. Screw fr nt c ver in p siti n.
Page 3

Page 4
JUMPER SWITCH
These fans are des gned to run cont nuously at a low speed w th a cho ce of three boost speeds (boost speed to be set at nstallat on).
The conf gurat ons for the opt onal boost speed are as follows:
ELP2204 - 4 Speed w th Cord
WIRING DIAGRAMS
ELP2204 - 4 Speed v a remote sw tch
IMPORTANT
If the fan is installed in a ceiling with a vertical duct passing
thr ugh an unheated space, a c ndensati n trap MUST be
fitted. Any ducting in an unheated space sh uld als be insu-
lated acc rding t the latest Building Regulati ns rec mmen-
dati ns in the D mestic Ventilati n C mpliance Guide.
Failure t d this c uld result in c ndensati n affecting the
perati n f the fan and cause damage t the ceiling.
If the fan s to be ce l ng mounted, the pull-cord sw tch
should be put n the “off” pos t on and the cord removed. A
remote sw tch w ll be necessary for chang ng the fan
speed. See w r ng d agrams,below.
INSTALLATION EXAMPLES
MAINTENANCE
Bef re any maintenance r cleaning p-
erati n, switch ff the fan and disc nnect
it fr m the main p wer supply.
The filter can be easily rem ved and
carefully washed.
The fr nt c ver and sides f fan can be
cleaned with a dry cl th r s ft brush.
The fan must NOT c me int c ntact
with any kind f liquid r s lvent. If this
sh uld ccur, c ntact a qualified techni-
cian bef re reassembling the fan.
NOTE: The motor does not requ re lubr -
cat on as t s ma ntenance free "sealed
for l fe" type.
DISMANTLING & RECYCLING - This
pr duct has been designed and c nstructed
using high-quality materials and c mp nents
that can be recy
cled r re-used.
Vectaire Ltd, Lincoln Road, Cressex Business Park, Hi h Wycombe, Buckin hamshire, HP12 3RH
Tel: [phone]. Fax: [phone]. Email: [email protected] Web: www.vectaire.co.uk
E & O.EELP 0716