Chromcraft Revington CH4257 User manual

STEP 3
STEP 2
HARDWARE LIST :
STEP 1
MADE IN MALAYSIA
PAGE 1 OF 3
ASSEMBLY :
TBSR-11393EF-CNNM-R
Allen Key
1 pc
(Small)
Flat Washer
8 pcs
JCBC Bolt
8 pcs
Wrench
1 pc
(Large)
Flat Washer
12 pcs
(Small)
Lock Washer
8 pcs
Hex Nut
12 pcs
(Large)
Lock Washer
12 pcs
SOLID TOP OVAL BUTTERFLY EXT . PED . TABLE (COUNTER HEIGHT / DINING)
Remove wood strip
(Small) Lock Washer
(Small) Flat Washer
(Small) Lock Washer
(Small) Flat Washer
JCBC Bolt
Bolt (M6)
Allen Key
Allen Key
Mounting Plate
Side Panel
Thread Head Thread Head
(long) (short)
4 pcs 4 pcs
Turn the pedestal upside down. Attach legs by inserting hanger
bolts through pre-drilled holes on pedestal, insert Flat Washer,
Lock Washer and Nut onto the Hanger Bolt then tighten
with the Wrench provided.
Wrench
Nut
(Large) Lock Washer
(Large) Flat Washer
PEDESTAL
LEVEL GLIDE
Bolt Bolt
To build a Gather Height Table use Hardware (A) Thread Head Bolt (long).
2.1 Turn the base right side up. Insert the Thread Head Bolt (long)
onto the column as shown in the below Figure 2.1.
To build a Dining Height Table use Hardware (B) Thread Head Bolt (short).
2.2 Turn the base right side up. Insert the Thread Head
Bolt (short) as shown in the below Figure 2.2. Thread Head Bolt (long)
(Fig 2.1)
Thread Head Bolt (short)
(Fig 2.2)
column
Counter height
table Dining table
(A) For Gather
Height Table only (B) For Dining
Height Table only
Position the table top upside down on a smooth, protective
surface such as carpet. Remove and discard the temporary
wood strip. Unscrew the side panel with screw driver then
Install the side panel and secure with Flat Washer(Small), Lock
Washer(Small) and JCBC Bolt. Attach mounting plate as shown.
Secure with Flat Washer(Small), Lock Washer(Small) and JCBC Bolt,
then tighten all the bolts with Allen Key provided.
Unscrew the
side panel

STEP 4
Lift both leaves from the compartment and flip up the apron then unfold Table Leaf and place the leaf on the top
surface carefully.
Flip up Apron
Unlock the hooks underneath the table and pull the table top wide open equally from bolt ends. Align and attach the
table top to the pedestal. Insert a Flat Washer,Lock Washer and Nut onto the Thread Head Bolt.Tighten all Nuts
with the Wrench provided.
STEP 5
MADE IN MALAYSIA
PAGE 2 OF 3
TBSR-11393EF-CNNM-R
Unlock Hook
Wrench
Nut
(Large) Lock Washer
(Large) Flat Washer
SOLID TOP OVAL BUTTERFLY EXT . PED . TABLE (COUNTER HEIGHT / DINING)

Lock Hook
TO STORE THE CENTRE LEAF WHEN NOT IN USE
STEP 6
Unlock Hook
Push Table Top from both ends to close gap and lock the hooks underneath table. Adjust the level glides until the
table sits firmly.
Unlock the hooks underneath the table and pull the table top wide open equally from both ends. Flip down the apron
and fold the centre leaf to store within the compartment. Push table top from both ends to close. Lock the hooks
underneath the table.
MADE IN MALAYSIA
PAGE 3 OF 3
TBSR-11393EF-CNNM-R
Lock Hook
Level Glide
Flip down Apron
SOLID TOP OVAL BUTTERFLY EXT . PED . TABLE (COUNTER HEIGHT / DINING)