Home Styles Pantry 88 5022 69 User manual

Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Hardware List
Tools required for assembly : Phillips screwdriver
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
Tools recommended for assembly : Level
88 5022 69
Pantry
D.
Side Panel
1 pc.
E.
Side Panel
1 pc.
F.
Stretcher
1 pc.
G.
Stretcher
2 pcs.
H.
Back Stretcher
4 pcs.
I.
Back Stretcher
2 pcs.
J.
Back Panel
4 pcs.
K.
Top
1 pc.
L.
Base
1 pc.
M.
Shelf
4 pcs.
N.
Door
1 pc.
O.
Door
1 pc.
P.
Door
1 pc.
Q.
Door
1 pc.
R.
Drawer
1 pc.
(Knock-Down Construction, please refer
to the last page of these instructions for
drawer assembly steps)
Cam Lock
30 pcs.(+1 extra)
Cam Lock Screw
30 pcs.(+1 extra)
M4x25
Machine Screw
8 pcs.
Adjustable Pin
16 pcs. (+1 extra)
Pull Handle
4 pcs.
M3.5x16
Wood Screw (short)
22 pcs. (+1 extra)
M3.5x25
Wood Screw (long)
for Drawer Side Part
8 pcs. (+1 extra)
Pull Handle
2 pcs.
A.
Top
1 pc.

Assembly Instructions 2/6
STEP 1
Put Cam Lock Screws into the pre-drilled holes of Top (A), (K) Side Panels (B),(C), (D), (E)
Base (L) and tighten.
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
*You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
B
C
D
E
A
K
L
Cam Lock Screw
Cam Lock Screw

Assembly Instructions 3/6
B
C
F
I
J
H
J
STEP 2
Attach Stretcher (F), (G) and
Back Stretcher (H) to
Side Panel (B) using Cam Locks.
Attach Back Stretcher (I) to
Back Stretcher (H).
Slide Back Panels (J) into place.
Attach Back Stretcher (H) to
unit using Cam Lock.
Attach Side Panel (C) to unit
using Cam Locks.
STEP 3
Attach unit from Step 2 to Base (L)
using Cam Locks.
Cam Lock
GH
Cam Lock
L

Assembly Instructions 4/6
STEP 4
Attach Door (P) and (Q) to unit
by sliding the door lift hinges
into the Side Panel lift hinges.
(see Figure 1)
Attach Top (K) to unit using
Cam Locks
STEP 5
K
Cam Lock
(Figure 1)
P
Q
D
E
H
I
J
J
H
G
Cam Lock
Attach Stretcher (G) and
Back Stretcher (H) to
Side Panel (D) using Cam Locks.
Attach Back Stretcher (I) to
Back Stretcher (H).
Slide Back Panels (J) into place.
Attach Back Stretcher (H) to
unit using Cam Lock.
Attach Side Panel (E) to unit
using Cam Locks.

Assembly Instructions 5/6
STEP 6
Attach unit from Step 5 to Top (K) using Cam Locks
Attach Door (N) and (O) to unit by sliding
the door lift hinges into the Side Panel lift hinges.
Place Top (A) onto unit using Cam Locks.
A
N
O
K
Attach the Door Pull Handle to
Doors (N), (O), (P) and (Q) using Machine Screws.
(see Figure 2)
Insert the Adjustable Pins into both Side Panels
at the desired level.
Place Shelves (M) and Drawer (R) into position.
To level the unit, adjust the adjustable
levelers on the bottom of unit. (see Figure 3)
Insert 16X Wood Screws (short) from the back
of the unit and tighten. (see Figure 4)
STEP 7
(Figure 2) (Figure 3)
(Figure 4)
Wood Screw (short)
M
M
M
M
P
Q
NO
R
Adjustable Pin
Cam Lock
Note: Unit must be level before tightening these screws.

R2
R3
R4
R5
R1
(Figure 3)
Insert wood screws (6X)short
into the pre-drilled holes in R5,
tighten screws. (see Figure 3)
Attach hardware pulls with
machine screws.
(see Figure 4)
Slide R5 into the grooves in R3
and R4. Be sure to push R5 all
the way forward to it meets R1.
(see Figure 2)
STEP 4
Tighten all screws used in
drawer assembly.
(Figure 1)
(Figure 2)
MAKE SURE ROLLER
IS ON THE BACK
R2
R3
R4
R5
R1
Drawer
Part List
R1.
Front Part
1 pc.
R5.
Base Part
1 pc.
R2.
Back Part
1 pc.
R3.
Side Part
1 pc.
R4.
Side Part
1 pc.
(Figure 4)
STEP 1
STEP 2
STEP 3
Attach R1 to R3 and R4, using
a andPhillips screwdriver
wood screws (4X),long
tighten halfway.
Attach R2 to R3 and R4 using
wood screws (4X),long
tighten halfway. (see Figure 1)
R1
R2
R4
R3
Assembly Instructions 6/6