CIC Frilled Lizard Installation guide

Manual
Assembly Instruction
&

(1:1)(1:1) (1:1)
Product Introduction
Mechanical Parts List
Gear With Shaft
Pinion Gear(White)
Tapping Screw
Gear(Red)
Gear(Purple)
Hex Shaft(Middle) Hex Shaft(Long)Hex Shaft(Short)
Gear(White)Gear(Yellow)
QTY
1
511
111
QTY
1
QTY
1
QTY
QTY QTY QTY
QTY QTY QTY
2
P4P3P2P1
P5 P6 P7
P8 P9
P10
Frilled Lizard Robot has an infrared sensor that is programmed to “escape” or “follow-me”.
If the infrared sensor is activated in the “escape” mode the robot will automatically act
“shocked!”, spreading its frill, dropping its jaw, illuminates its bicolor LED eyes and will
scurry away from you until it escapes to a safe distance. If the infrared sensor is switched
to the “follow-me” mode using the 2 way function switch, then the robot will assess danger
by bluffing the attacker (unfurling and shaking its frill). When the robot does not sense
danger it will proceed to follow you like a pet lizard.
Thank goodness, that unlike the wacky frilled lizard that roams in Australia’s tropical
woodland, this Frilled Lizard Robot is whimsically kooky and fun to build.
Product contains functional edges and sharp points.
Frilled Lizard Robot KIT
1
Alkaline batteries are
recommended
Tools You May Need
Diagonal Cutter Knife
Battery(AAA) x 4 Screwdriver
Hammer

(Spare part : 1 pc)
Sticker
Round Shaft Round Shaft PC Board
112
QTY QTY QTY
P13P11 P12
Motor With Connector Motor With Connector
Battery Holder With Connector
11
QTY QTY
P15P14
Black
W / Short Wires
Black
Red Red
PC Board With Connector
11
QTY QTY
P17P16
Frill
Spare Parts
1
1
QTY QTY
P18
1
QTY
P20
Adhesive Tape
P19
W / Long Wires
2
DC 6V

Cut the plastic parts when they are required.
Do not cut them in advance.
2
2 1
E
5
4
32
6
7
89
1B
10
11
12
9
12
16
17
181920212223
24
25
15
14 10
11
13
8
3
45 2
1
C
L
67
C3
C4
R
1
6
7
8
9
A8
A11
A1
A2
2
3
5
12
13
11
10
10
9
4
A
1
2
34
D
012
Plastic Parts
burr burr
burr
Tip:cut off the burrs before assembly
Spare Parts
Spare Part
3

Head Module Assembly
4
1
C9
2
C6
C15
C5

55
Side View
P2(Red)
P8
(Short)
C13
P1
P14
B3
RedBlack
5
3 4
5
1
1
1
2
2
1:1
W / Short Wires

Make sure “ “ to be faced up to you,
it is to assist you in assembling C8 correctly.
6
6
7
8
1
2
2
C8
B4x6
Black
Red

7
9
10
P19
A13
P18
A7
A9 A9
A10A10
Cut the frill as below illustration.
Make sure adhesive tapes come with thin glued films while tearing off.
*Includes an extra frill

A10A10
A13
A7
The opposite (no printing)
side to be faced up.
No stickers on the printing side.
8
11
Front Back
A9

Pull
9
12
A9
A9
A10
A10
A13
A7

10
A9
A13
A10 A10
Note: Frill is not pictured below to clearly illustrate assembly.
1
1
1
1
2
2
2
2

11
3PUSH
A9
A7
1
12
2

12
13
D3
D4
B9
P17
D2
B10

13
14
15
C12
12
2
2
1
3

Push
14
16

Do not mix up C4 & C3,
make sure C4 for assembly.
Body Module Assembly
15
1
2
P11
C23
P3
(Yellow)
C4
P5
(Purple)
P10(Long)
C22
1:1
very important!

C14
16
3
4 5
P1
P15
B2
P6
P4(White)
P11
W / Long Wires

1:1
C17
C18
P12
17
6
7
C10
Hammer slightly.

1:1
Do not mix up C4 & C3,
make sure C3 for assembly.
C21
C11
C3
18
8
9
B5
B1
P9
(Middle)
Important!

19
B1
10
11
12
2
1
B6