Cine Gears Rattlesnake Product guide

RATTLESNAKE WIRELESS
FOLLOW FOCUS CONTROLLER
MANUAL BOOK
© 2017 Cine Gears INC. All Rights Reserved.

© 2017 Cine Gears INC. All Rights Reserved.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, Cine
Gears Inc. reserves the right to make changes to the products described in this docu-
ment without notice.
Cine Gears Inc. does not assume any liability that may occur due to the use or applica-
tion of the product(s) or circuit layout(s) described herein.
FCC Compliance Notice: Radio Frequency Notice
The device has met the FCC 15.247 requirement. In order to comply with the FCC RF
exposure requirement, the user must keep 20cm away from the antenna.
This device has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
device generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following mea-
sures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

© 2017 Cine Gears INC. All Rights Reserved.
Information to the user
The user’s manual or instruction manual for an intentional or unintentional radiator
shall caution the user that changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equip-
ment. In cases where the manual is provided only in a form other than paper, such as
on a computer disk or over the Internet, the information required by this section may
be included in the manual in that alternative form, provided the user can reasonably be
expected to have the capability to access information in that form.

Contents
Introduction
Rattlesnake Follow Focus User Manual
Disclaimers
About Cinegears
© 2017 Cine Gears INC. All Rights Reserved. 1
2
3
6
8

Introduction
The Cinegears Rattlesnake Controller is a wireless lens control kit for
driving your lens rings (focus, iris, and zoom.) The Cinegears Rattlesnake
Controller has been redesigned to be more ergonomic than ever before.
With up to 20 hours of continuous shooting per battery charge, control your
lens focus, iris, or zoom with precision from up to 200 meters away with our
Cinegears Rattlesnake Controller. Our controllers work with jib, Steadicam,
MoVI, and Gimbal stabilizer shots, allowing you to perform with precision
without sacrificing the mobility of your cameras or the integrity of the shot. The
larger focus wheel feels more fluid, precise, and ergonomic, and the mounting
harness allows you to use it like a finger wheel. Also included are two thick
magnetic marking discs and a redesigned Lemo cable, with a right-angle
connector that helps keep your wiring clean.
© 2017 Cine Gears INC. All Rights Reserved. 2
FCC ID: 2AM4ZXYAM
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.

User Manual
Battery
The Rattlesnake Wireless Follow Focus Controller runs on one 18650 lithium
ion battery. LiCB rechargeable batteries and batteries with a higher capacity
are recommended. As the Controller functions as a charger, an external battery
charger is not required. To charge the battery, connect the Rattlesnake Controller
to a power source via the USB cable provided in the kit. With the vibration setting
turned off, one fully charged battery will power the unit for up to 3 days.
Synchronization
Turn on the remote control power switch and plug in the motor. Once both are
on, press and hold the CODE button on the motor for 3 seconds until it turns green.
Then, hold (SET) + (POWER) on the controller for 3 seconds. The motor light will
stop blinking, and the gear will shudder. This means that the controller and motor
have been successfully synchronized. (Note: This process is usually done before
leaving the factory.)
Setting Presets
Go to the focus point of your choosing, press and hold (A) button until it flashes,
your point is now set. Repeat with (B) (C) and (D) for multiple points. Press the
same preset button to exit the preset mode.
Changing Motor Speed Between Presets
Press (SPEED) on the controller to adjust the motor speed between presets.
Automatic Calibration
To calibrate your lens, hold the (SET) + (A) button on the remote controller for 3
seconds. NOTE: Before installing the drive onto the lens, please make sure the
wireless remote controller and motor are powered on and connected. DO NOT turn
the wireless remote control dial, put the drive gear close to the lens ring and tighten
the screws.The controller can automatically locate the start and end points of any lens.
© 2017 Cine Gears INC. All Rights Reserved. 3
Controller
The controls have been designed for ease of use: They allow for preset
memory points, where you can save up to four, as well as two lock points
that will cause the controller to vibrate as you approach them. Choose from 16
different speed levels to control the transition speed of the presets, and 4 different
damping levels from ultraresponsive to ultra smooth. The controller has an accuracy
circuit built into it to ensure the lens stop precisely where you want it to, even after
repeated use.

User Manual
© 2017 Cine Gears INC. All Rights Reserved. 4
Manual Calibration
Specifically used with infinity lenses that have no start or end point. Press
(SET) + (B) for 3 seconds until you see the (A), (B), (C), (D) lights go on. Then use
(C) or (D) button to control the lens. (Hold down the C or D key for more
than 3 seconds to rotate continuously.) Once it rotates to the proper
position, click the (A) button to set a starting point, (B) button to set the end point.
After points are set, the (A), (B), (C), and (D) lights turn off to indicate the initialization
has been completed.
Recalibrating Your Controller
Rotate the focus ring clockwise to desired start point; hold (SET) + (REC) + (POWER)
buttons together for 3 seconds. Rotate to the desired end point and press (SET)+
(REC)+(POWER) for 3 seconds again.
Setting Up Vibration and Lock Points
To turn the vibration on or off, press and hold (REC) for 3 seconds.
Press and hold (REC) + (A) to set controller to “M-Normal.” Lock points can
only be set while controller is in “M-Normal” mode.
To set one lock point, turn controller to desired start point and press and hold
(SET) + (C) for 3 seconds.
To set a second lock point, turn the controller to the desired point and press
and hold (SET)+(D) for 3 seconds.
To set the controller to “M-Lock” mode, press and hold (REC)+(B) for 3
seconds. In “M-Lock” mode, controller cannot move past set lock points.
To set the controller to “M-Zoom” mode, press and hold (REC)+(C) for 3
seconds. In “M-Zoom” mode, controller cannot move past set lock points. In
“M-Zoom,” controller also moves more slowly between set lock points for
finer control.
To clear all lock points, press and hold (REC) + (D).

User Manual
User Manual
© 2017 Cine Gears INC. All Rights Reserved. 5
Remote Record Trigger
Press (REC) on your controller to toggle Recording mode ON or OFF.
Changing Damping Setting
Press and hold (POWER) + (REC) + (A) to set motor to damping 1 (Responsive +).
Press and hold (POWER) + (REC) + (B) to set motor to damping 2 (Responsive).
Press and hold (POWER) + (REC) + (C) to set motor to damping 3 (Smooth).
Press and hold (POWER) + (REC) + (D) to set motor to damping 4 (Smooth +).
LED Marker Light
Press (POWER) quickly to toggle marker light ON or OFF.
Screen Brightness
To change screen brightness, press and hold (SPEED) + (A), (B), (C), or (D),
(SPEED) + (A) being the lowest brightness level, (SPEED) + (D) being the
highest brightness level.

© 2017 Cine Gears INC. All Rights Reserved. 6
Disclaimers
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment. (Example use only
shielded interface cables when connecting to computer or peripheral devices).
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired
operation.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user authority to operate the
equipment.
FCC Statement
FCC Radiation Exposure Statement
Cautions

© 2017 Cine Gears INC. All Rights Reserved. 7
Disclaimers
Terms and Conditions
Congratulations on purchasing your new CINEGEARS product. Please read this manual carefully before
using the product. By using this product, you hereby agree to this disclaimer and signify that you have read
it in full. You agree that you are responsible for your own conduct and any content created while using
CINEGEARS products, and for any consequence thereof. You agree to use this product only for purposes
that are proper and in accordance with local regulations, terms and any applicable polices and guidelines.
By reading this disclaimer, you also agree:
1. Any part of this disclaimer is subject to change without prior notice. Refer to
WWW.CINEGEARS.COM for the latest version.
2. CINEGEARS reserves the right of final interpretation of this disclaimer.
CINEGEARS and the Follow Focus Kit are registered trademarks of Littlecent International Trading Corp. as
names of product, brand, etc., appearing in this manual are trademarks or registered trademarks of their
respective owner companies. This product and manual are copyrighted by CINEGEARS with all rights
reserved. No part of this product or manual shall be reproduced in any form without the prior written consent
or authorization of CINEGEARS.

About Cine Gears Inc.
© 2017 Cine Gears INC. All Rights Reserved. 8
Customer Support
Cine Gears Inc. is an industry leading company that designs and manufactures digital
wireless follow focus systems, lens control systems, camera motion control systems
and accessories for film and broadcast industry. As a big believer in the power of
creativity and ideas, we designed the Pegasus cablecam, the wireless motor drive that
integrated a built in wireless transmitter, and the wireless finger wheel controller. The
Cine Gears Inc. wireless lens control system has the international CE certification on
all its equipment. Cine Gears lens control system can achieve the finest minutia of
focus pulling, with extreme accuracy and control. This very same technology is what
drives the Pegasus for ultra-smooth, highly controlled, programmed movement.
We have been working from Vancouver, B.C. for five years and our equipment has
been used on hundreds of movies. Filmmakers of all experience levels will benefit
greatly from a simple, professional, and well rounded follow focus system. The Single
Axis and Multi Axis models provide greater ease, with lesscrew, and less wires. You
can achieve professional film quality scenes on a shoestring budget. Camera
operators, assistant camera operators, and jib operators can use the wireless follow
focus to attain that perfect shot.
If you encounter any issues with any of our products please contact us directly
via the details provided below. DO NOT CONTACT THE RETAIL STORE.
CINE GEARS INC. (Canada)
2nd floor 2010-9111 Beckwith Road
Tel: [phone]
CINE GEARS INC. (USA)
47 East South Street, Suite 401
Frederick, Maryland 21701, USA
Tel: [phone]
Toll Free: 1 800 693 8883
Richmond, BC V6X 1V7, Canada