Cisco 2100 Series User manual

TAKE OUT WHAT YOU NEED
RACK MOUNT THE HARDWARE
CONNECT CABLES
RUN THE SETUP PROGRAM
1
2
3
4
Quick Start Guide
CISCO INTELLIGENCE ENGINE 2100 SERIES
MOUNTING, CABLING, AND SETUP
MODE
MODE
MODE
Cisco Intelligence Engine 2100 Series
Routers
Routers
Routers
Console
Hub
53002
DRIVE0DRIVE1
MODE
MODE
MODE
MODE
MODE
MODE
MODE

1
Take Out What You Need
This guide explains how to mount, cable, and set up
your Cisco Intelligence Engine 2100 Series
(IE2100 Series).
Product Documentation
1 Quick Start Guide (this guide)
1 Regulatory Compliance and Safety Information
for Cisco Intelligence Engine 2100 Series
1 Cisco Intelligence Engine 2100 Series
Configuration Registrar Manual (for more detailed
information about subjects covered in this guide)
1 Release Notes for Cisco Intelligence Engine 2100
Series Configuration Registrar
Hardware Appliance
1 Cisco Intelligence Engine 2100 Series
53000
Intelligence Engine 2100 Series
LINK
CONSETHERNET0 ETHERNET1
100MbpsLINK100MbpsDRIVE0 DRIVE1
MODE

2
Take Out What You Need (continued)
Cables and Power Cord
1 yellow Ethernet 10BaseT cable
(to connect to a 10BaseT hub)
1 flat, light-blue console cable with
1 RJ-45 adapter, labeled TERMINAL
(RJ-45-to-DB-9)
1 black power cord
Rack-Mount Kit
2 L mounting brackets (left and right)
4 M4 Phillips countersunk-head screws
4 12-24 x 3/4-inch Phillips binder-head screws
4 10-32 x 3/4-inch slotted binder-head screws
1 8-32 x 1/2-inch black Phillips binder-head screw
Desktop-Mount Kit
4 Desktop mounting self-adhesive feet

3
Rack Mount the Hardware
49336
Intelligence Engine 2100 Series
LINK
CONS ETHERNET 0 ETHERNET 1
100Mbps LINK 100MbpsDRIVE 0 DRIVE 1
MODE
Phillips machine
screws
Installing Rack Mount
Hardware
This section describes how to install the
IE2100 Series in a standard 19-inch equipment rack.
A rack-mount kit is included for mounting the
system in a standard 19-inch equipment rack with
two unobstructed outer posts.
Note You can place the system on a desktop or other
flat, stable surface. Self-adhesive rubber feet are
provided for this purpose.
Warning The following guidelines are
provided to ensure your safety:
• This unit should be mounted at the bottom of
the rack if it is the only unit in the rack.
• When mounting this unit in a partially filled
rack, load the rack from the bottom to the top
with the heaviest component at the bottom of
the rack.
• If the rack is provided with stabilizing devices,
install the stabilizers before mounting or
servicing the unit in the rack.
To install the IE2100 Series in a rack:
Step 1 Measure the rack to verify that the system
will fit.
Step 2 Attach the L brackets to the sides of the
chassis using the provided screws so that
the L-bracket mounting surfaces are even
with the front or back panel of the chassis,
depending on which way you want to
install it.
Step 3 Position the chassis in the rack.
Step 4 Align the four mounting holes in the
L bracket with the four mounting holes in
the equipment rack.
Step 5 Secure the system in the rack by installing
the provided screws through the elongated
holes in the L bracket and into the
threaded holes in the mounting post.

4
Connect Cables
MODE
MODE
MODE
Cisco Intelligence Engine 2100 Series
Routers
Routers
Routers
Console
Hub
53002
DRIVE0DRIVE1
MODE
MODE
MODE
MODE
MODE
MODE
MODE
Connecting the Ethernet and
Console Cables
Use the console cable in the accessory kit to connect
the IE2100 Series console port (CONS) to a console or
computer that is running a console program.
Use the CAT 5 UTP cable in the accessory kit to
connect the IE2100 Series to your network.
Cisco Intelligence Engine 2100 Series
Console cable
Console
Cons Port (RJ-45)
53006
Intelligence Engine 2100 Series
LINK
CONSETHERNET0 ETHERNET1
100MbpsLINK100MbpsDRIVE0DRIVE1
MODE
Cisco Intelligence Engine 2100 Series
Ethernet Hub
(sold separately)
CAT 5 UTP cable
Ethernet 10/100BaseTX
port (RJ-45)
53005
Intelligence Engine 2100 Series
LINK
CONSETHERNET0 ETHERNET1
100MbpsLINK100MbpsDRIVE0 DRIVE1
MODE

5
Connect Cables (continued)
AC power
connector
49334
Power switch
Power receptacle
Connect the Power Cable
Step 1 Verify that the Power switch is set to OFF.
Step 2 Connect the black power cable to the
power receptacle on the rear panel of the
IE2100 Series.
Step 3 Connect the other end of the power cable
to an AC power source.
Step 4 Set the power switch to ON.
Step 5 Verify that the IE2100 Series is
operational.

6
Run the Setup Program
This section explains how to run the setup program
to configure the system.
Step 1 Boot the system without a configuration.
When the system finishes booting, a login
prompt appears.
Step 2 Log in with the username of setup.
Step 3 Enter responses to the prompts that appear:
hostname
System hostname. Appears in command
prompt.
domain name
System domain name.
admin password
Password for the Linux administrative
user account on the IE2100 Series; case
sensitive, between 5 and 20 characters.
confirm password
Reenter password to verify that you typed
it correctly.
eth0 IP address
IP address of Ethernet 0 interface.
eth0 network mask
Network mask of Ethernet 0 interface.
eth0 default gateway IP address
IP address of default router that connects
IE2100 Series to network.
eth1 IP address
Optional. To skip, press Enter.
eth1 network mask
Optional. To skip, press Enter.
eth1 default gateway IP address
Optional. To skip, press Enter.
Primary DNS nameserver IP address
IP address of DNS server that
IE2100 Series uses for name/IP-address
resolution.
Secondary DNS nameserver IP address
Optional. To skip, press Enter.
enter country code
Enter the two (2) character country code.
enter Location code
Enter the location code or name without
embedded blanks.
enter Configuration Server username
Username for the Configuration Registrar
administrative account; case-sensitive
with a maximum of 32 characters.
<username> password
Password for the administrative user
account on the Configuration Registrar;
case sensitive, between 5 and 20
characters.
confirm password
Reenter password to verify that you typed
it correctly.
Would you like to save this configuration
[yes]
Press Enter to accept the configuration.
The configuration is saved.
Step 4 Log in as admin.
Step 5 Type rootenable.
Step 6 Set your root password.
Caution If you forget your root password,
you will be locked out of the system!

7
Run the Setup Program (continued)
Verify Configuration Registrar
is Running
Once the system has been installed and configured,
you can verify the installation of the Configuration
Registrar by following these steps:
Step 1 Go to a different computer and bring up a
web browser.
Step 2 On the net-site window enter the URL for
the Configuration Registrar.
For example:
http://<ip_address>/config/login.html
where: ip_address is the IP address you
entered during IE2100 Series setup.
The Configuration Registrar login page
appears.
Step 3 Enter the Configuration Registrar Userid
and Password that you entered during
IE2100 Series setup.
Step 4 On the message page, click Continue.
If you have reached the Configuration
Registrar Home page, you have verified the
successful installation on the Configuration
Registrar.