Cisco FMC 1600 Manual

Cisco Firepower Management Center 1600, 2600, and 4600 Hardware
Installation Guide
First Published: 2019-06-26
Last Modified: 2021-05-03
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of
the UNIX operating system. All rights reserved. Copyright ©1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.
All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version.
Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL:
https://www.cisco.com/c/en/us/about/legal/trademarks.html. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a
partnership relationship between Cisco and any other company. (1721R)
©2019-2021 Cisco Systems, Inc. All rights reserved.

CONTENTS
Overview 1
CHAPTER 1
Features 1
Package Contents 3
Serial Number Locations 4
Front Panel 6
Front Panel LEDs 9
Rear Panel 12
Rear Panel LEDs 13
Power Supply 14
Hardware Specifications 15
Product ID Numbers 15
Power Cord Specifications 16
Installation Preparation 25
CHAPTER 2
Installation Warnings 25
Safety Recommendations 28
Maintain Safety with Electricity 28
Prevent ESD Damage 29
Site Environment 29
Power Supply Considerations 29
Rack Configuration Considerations 30
Rack-Mount the Chassis 31
CHAPTER 3
Unpack and Inspect the Chassis 31
Rack-Mount the Chassis 31
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
iii

Installation, Maintenance, and Upgrade 35
CHAPTER 4
Power Button Shutdown 35
Remove and Replace a Drive 36
Remove and Replace a Power Supply 38
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
iv
Contents

CHAPTER 1
Overview
•Features, on page 1
•Package Contents, on page 3
•Serial Number Locations, on page 4
•Front Panel, on page 6
•Front Panel LEDs, on page 9
•Rear Panel, on page 12
•Rear Panel LEDs, on page 13
•Power Supply, on page 14
•Hardware Specifications, on page 15
•Product ID Numbers, on page 15
•Power Cord Specifications, on page 16
Features
The Cisco Firepower Management Center (FMC) 1600, 2600, and 4600 management appliances run software
that provides extensive intelligence about the users, applications, devices, threats, and vulnerabilities that exist
in your network. It also uses this information to analyze your network’s vulnerabilities. It then provides tailored
recommendations on what security policies to put in place and what security events you should investigate.
See Product ID Numbers, on page 15 for a list of the field-replaceable product IDs (PIDs) associated with
the FMC 1600, 2600, and 4600. You can remove and replace drives and power supplies. For all other internal
component failures, you must send your chassis for return material authorization (RMA).
The FMC management appliances support Cisco Firepower Threat Defense software. See the Cisco Firepower
Compatibility Guide, which provides Cisco Firepower software and hardware compatibility, including operating
system and hosting environment requirements, for each supported Firepower version.
The following table lists the features of the FMC 1600, 2600, and 4600.
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
1

Table 1: FMC 1600, 2600, and 4600 Features
460026001600Feature
• Common Criteria (CC) on FTD 6.4.x
• Federal Information Processing Standards (FIPS) 140-2 on FTD 6.4.x
•Department of Defense Information Network Approved Product List (DoDIN
APL)
• US Government Compliance for IPv6 (USGv6) and Ready Logo certified
on FTD 6.4.x
See the "Security Certifications Compliance" topic in the "Appliance Platform
Settings" chapter in the Firepower Management Center Configuration Guide,
Version 6.7 for the instructions on how to enable security certifications
compliance.
Security standards
certifications
1 RUForm factor
Standard 19-in. (48.3 cm) 4-post EIA rackRack mount
Front to rear
Cold aisle to hot aisle
Airflow
Displays the serial number and the MAC address for the two built-in management
ports
Pullout asset card
Two threaded holes for a dual-hole grounding lug
Use is optional; the supported AC power supplies have internal grounding, so
no additional chassis grounding is required.
Grounding hole
On the front panelUnit identification button
On the rear panelPower button
Two Intel Xeon 4116
processors
Two Intel Xeon 4110
processors
One Intel Xeon 4110
processor
Processor
128-GB RAM64-GB RAM32-GB RAMMemory
Eight 16-GB
DDR4-2400-MHz
DIMMs
Four 16-GB
DDR4-2400-MHz
DIMMs
Two 16-GB
DDR4-2400-MHz
DIMMs
RDIMMs
Internal component only;
not field-replaceable
Two built-in RJ-45 SFP+ ports
Support for 1000 Mbps, 1 Gbps, and 10 Gbps
The primary management port is eth0. You can use eth1, eth2, and eth3 as
secondary management or event ports.
Management ports
Two USB 3.0 Type AUSB ports
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
2
Overview
Features

460026001600Feature
One 3-row 15-pin DB-15 connector
Enabled by default
VGA port
Two fixed SFP+ portsSFP ports
SFP-10G-SR (10 Gb)
SFP-10G-LR (10 Gb)
Only these two SFPs have been qualified for use on the FMC. Although
non-Cisco SFPs and other Cisco SFPs are allowed, we do not
recommend using them because they have not been tested and validated
by Cisco. Cisco TAC may refuse support for any interoperability
problems that result from using an untested SFP transceiver.
Note
Supported SFP+
RJ-45 serial port running RS-232 (RS-232D TIA-561)Serial console port
Two 770-W AC power supplies
Hot-swappable and redundant as 1+1
System power
2626 BTU/hrPower consumption
Six fans for front-to-rear cooling
Internal component only; not field-replaceable
Fans
Ten 1.2-TB SAS HDDs
RAID 6, hot-swappable
Four 600-GB 10-K SAS
HDDs
RAID 5, hot-swappable
Two 1.2-TB 10-K SAS
HDDs
RAID 1, hot-swappable
Storage
Package Contents
The following figure shows the package contents for the FMC 1600, 2600, and 4600. Note that the contents
are subject to change and your exact contents might contain additional or fewer items.
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
3
Overview
Package Contents

Figure 1: Package Contents
RJ-45 to DP9-RS232 console cable (Cisco part
number 72-3383-XX)
2Chassis1
RJ-45 to RJ-45 Cat 5 Ethernet cable, yellow six
feet long (Cisco part number 72-1482-XX)
4Cisco rail kit (Cisco part number 800-43376-02)3
Two 10-Gb SFP+ transceivers with cables
Optional for all models; in package if ordered.
6Useful Links Cisco Firepower Management
Center 1600, 2600, and 4600
The steps in the Useful Links document send you
to the documentation you need to install, set up,
and configure your FMC.
5
Serial Number Locations
The serial number (SN) for the FMC 1600, 2600, and 4600 is printed on the pullout asset card located on the
front panel as shown in the following figure of the FMC 1600.
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
4
Overview
Serial Number Locations

Figure 2: Serial Number on Pullout Asset Card
The serial number is also on the label on the cover of the chassis as shown in the following figure.
The cover latch on the top of the chassis cover is not supported. There are no internal field-replaceable parts
in the FMC 1600, 2600, and 4600.
Caution
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
5
Overview
Serial Number Locations

Figure 3: Serial Number Location on Cover
Cover latch
Not supported
2Serial number label1
Front Panel
The following figure shows the front panel features and disk-drive configuration for the FMC 1600. See Front
Panel LEDs, on page 9 for a description of the LEDs.
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
6
Overview
Front Panel

Figure 4: FMC 1600 Front Panel
Power button/power status LED2Drive bays
Supports two SAS HDDs in slots 1 and 2
1
System status LED4Unit identification button/LED3
Fan status LED6Power supply status LED5
Temperature status LED8Network link activity LED7
Keyboard, video, and mouse (KVM) port
Not supported; use the VGA and USB keyboard
ports instead.
10Pullout asset card9
The following figure shows the front panel features and disk-drive configuration for the FMC 2600. See Front
Panel LEDs, on page 9 for a description of the LEDs.
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
7
Overview
Front Panel

Figure 5: FMC 2600 Front Panel
Power button/power status LED2Drive bays
Supports four SAS HDDs in slots 1 through 4
1
System status LED4Unit identification button/LED3
Fan status LED6Power supply status LED5
Temperature status LED8Network link activity LED7
KVM port
Not supported; use the VGA and USB keyboard
ports instead.
10Pullout asset card9
The following figure shows the front panel features and disk-drive configuration for the FMC 4600. See Front
Panel LEDs, on page 9 for a description of the LEDs.
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
8
Overview
Front Panel

Figure 6: FMC 4600 Front Panel
Power button/power status LED2Drive bays
Supports ten SAS SSDs in slots 1 through 6
1
System status LED4Unit identification button/LED3
Fan status LED6Power supply status LED5
Temperature status LED8Network link activity LED7
KVM port
Not supported; use the VGA and USB keyboard
ports instead.
10Pullout asset card9
Front Panel LEDs
The following figure shows the front panel LEDs and describes their states.
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
9
Overview
Front Panel LEDs

Figure 7: Front Panel LEDs and Their States
Drive activity LED:
• Off—There is no drive in the drive tray (no
access, no fault).
• Green—The drive is ready.
• Green, flashing—The drive is reading or
writing data.
2Drive fault LED:
• Off—The drive is operating properly.
• Amber—Drive fault detected.
• Amber, flashing—The drive is rebuilding.
• Amber, flashing with 1-second
interval—Drive locate function activated in
the software.
1
Unit identification LED:
• Off—The unit identification function is not
in use.
• Blue, flashing—The unit identification
function is activated.
4Power LED:
• Off—There is no AC power to the chassis.
• Amber—The chassis is in standby mode.
• Green—The chassis is in main power mode.
Power is supplied to all components.
3
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
10
Overview
Front Panel LEDs

Power supply status LED:
• Green—All power supplies are operating
normally.
• Amber—One or more power supplies are in
a degraded operational state.
• Amber, flashing—One or more power
supplies are in a critical fault state.
6System status LED:
• Green—The chassis is running in normal
operating condition.
• Green, flashing—The chassis is performing
system initialization and memory check.
• Amber—The chassis is in a degraded
operational state (minor fault).
• Power supply redundancy is lost.
• CPUs are mismatched.
• At least one CPU is faulty.
• At least one DIMM is faulty.
• At least one drive in a RAID
configuration failed.
• Amber, two flashes—There is a major fault
with the system board.
•Amber, three flashes—There is a major fault
with the DIMMs.
• Amber, four flashes—There is a major fault
with the CPUs.
5
Network link activity LED:
• Off—The Ethernet port link is idle.
• Green—One or more Ethernet ports are
link-active, but there is no activity.
•Green, flashing—One or more Ethernet ports
are link-active with activity.
8Fan status LED:
• Green—All fans are operating properly.
• Amber, flashing—One or more fans
breached the unrecoverable threshold.
7
Temperature status LED:
• Green—The chassis is operating at normal
temperature.
• Amber—One or more temperature sensors
breached the critical threshold.
• Amber, flashing—One or more temperature
sensors breached the unrecoverable
threshold.
9
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
11
Overview
Front Panel LEDs

Rear Panel
The Cisco Integrated Management Controller (CIMC) is only supported for Lights-Out Management (LOM)
access on the CIMC port (labeled M) on a Serial Over LAN (SOL) connection to remotely monitor or manage
the FMC system. For information on using LOM and SOL, see the "Set Up Lights Out Management" section
in the Cisco Firepower Management Center Getting Started Guide for Models 1600, 2600, and 4600.
Note
The following figure shows the rear panel of the FMC 1600, 2600, and 4600.
Figure 8: Rear Panel
USB 3.0 Type A (USB 2)
You can connect a keyboard, and along with a
monitor on the VGA port, you can access the
console.
2USB 3.0 Type A (USB 1)
You can connect a keyboard, and along with a
monitor on the VGA port, you can access the
console.
1
eth1 management interface (labeled 2)
Gigabit Ethernet 100/1000/10000 Mbps interface,
RJ-45, LAN2
4eth0 management interface (labeled 1)
Supports 100/1000/10000 Mbps depending on
link partner capability.
3
CIMC interface (labeled M)
CIMC is supported only for LOM
access. CIMC is not supported on any
other interfaces.
Note
6VGA video port (DB-15 connector)5
Unit identification button8Serial console port (RJ-45 connector)
Disabled by default; use the VGA port and
keyboard USB port instead. For more information
on the serial port, see the "Set up Serial Access"
topic in the Cisco Firepower Management Center
Getting Started Guide for Models 1600, 2600,
and 4600.
7
770-W AC power supply (PSU 2)10770-W AC power supply (PSU 1)9
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
12
Overview
Rear Panel

eth2 management interface
(Optional) 10-Gigabit Ethernet SFP+ support
SFP-10G-SR and SFP-10G-LR are qualified for
use on the FMC.
12Threaded holes for dual-hole grounding lug11
Riser handle
Not supported
14eth3 management interface
(Optional) 10-Gigabit Ethernet SFP+ support
SFP-10G-SR and SFP-10G-LR are qualified for
use on the FMC.
13
Rear Panel LEDs
The following figure shows the rear panel LEDs and describes their states.
Figure 9: Rear Panel LEDs and Their States
100-Mbps/1-Gbps/10-Gbps Ethernet link status
(speed on both LAN1 and LAN2):
• Off—No link is present.
• Green—Link is active.
• Green, flashing—Traffic is present on the
active link.
2100-Mbps/1-Gbps/10-Gbps Ethernet link (speed
on both LAN1 and LAN2):
• Off—Link speed is 100 Mbps.
• Amber—Link speed is 1 Gbps.
• Green—Link speed is 10 Gbps.
1
1-Gbps Ethernet dedicated management link:
• Off—No link is present.
• Amber—Link is active.
• Green, flashing—Traffic is present on the
active link.
41-Gbps Ethernet dedicated management link:
• Off—Link speed is 10 Mbps.
• Amber—Link speed is 100 Gbps.
• Green—Link speed is 1 Gbps.
3
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
13
Overview
Rear Panel LEDs

Power supply (one LED for each power supply):
• Off—No AC input (12-V main power off;
12-V standby power off)
•Green, flashing—12-V main power off; 12-V
standby power on.
• Green—12-V main power on; 12-V standby
power on.
• Amber, flashing—Warning threshold
detected but 12-V main power on.
• Amber—Critical error detected; 12-V main
power off ( for example, overcurrent,
overvoltage, or overtemperature failure).
6Unit identification:
• Off—The unit identification function is not
in use.
• Blue, flashing—The unit identification
function is activated.
5
Power Supply
The following table lists the specifications for each 770-W AC power supply used in the FMC 1600, 2600,
and 4600.
Table 2: Power Supply Specifications
SpecificationDescription
1313 BTU/hrPower consumption
Nominal range: 100 to 120 V AC, 200 to 240 V AC
Range: 90–132 V AC, 180–264 V AC
AC input voltage range
Nominal range: 50–60 Hz
Range: 47–63 Hz
AC input frequency
9.5 A peak at 100-V AC
4.5 A peak at 208 V AC
Maximum AC input current
950 VA at 100 V ACMaximum input volt amperes
770 WMaximum output power for each power supply
15 A (subcycle duration)Maximum inrush current
12 ms at 770 WMaximum hold-up time
12 V DCPower supply output voltage
12 V DCPower supply standby voltage
Climate Savers Platinum Efficiency (80 Plus Platinum
certified)
Efficiency rating
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
14
Overview
Power Supply

SpecificationDescription
RSP2Form factor
IEC320 C13/C15Input connector
Hardware Specifications
The following table lists the hardware specifications for the FMC 1600, 2600, and 4600.
Table 3: FMC 1600, 2600, and 4600 Hardware Specifications
460026001600Specification
1.7 x 16.89 x 29.8 in. (4.32 x 43.0 x 75.6 cm)Dimensions (H x W x D)
36.0 lb (17.0 kg)34.1 lb (16.8 kg)
32.2 lb (16.6 kg)Weight
Operating: 50 to 95°F (10 to 35°C)
Maximum temperature is derated by 1°F/547 ft (1°C/300 m) of altitude above
3117 ft (950 m).
Nonoperating: –40 to 149°F (–40 to 65°C)
When the appliance is stored or transported.
Temperature
Operating: 8 to 90% noncondensing
Nonoperating: 5 to 95% noncondensing
Relative humidity
Operating: 0 to 10,000 ft
Nonoperating: 0 to 40,000 ft when the appliance is stored or transported
Altitude
5.8 Bels (measure A-weighted per ISO7779 LWAd)
Operation at 73°F (23°C)
Sound power level
43 dBa (measure A-weighted per ISO7779 LpAM)
Operation at 73°F (23°C)
Sound pressure level
Product ID Numbers
The following table lists the field-replaceable PIDs associated with the FMC 1600, 2600, and 4600. The spare
components are ones that you can order and replace yourself. If any internal components fail, you must get a
return material authorization (RMA) for the entire chassis including the SFPs and SFP cables. Remove the
drives and power supplies before you send the chassis for RMA. See the Cisco Returns Portal for more
information.
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
15
Overview
Hardware Specifications

Table 4: FMC 1600, 2600, and 4600 PIDs
DescriptionPID
AC power supplyFMC-M5-PS-AC-770W
AC power supply (spare)FMC-M5-PS-AC-770W=
FMC 1600 and 4600 1.2-TB driveFMC-M5-HDD-1.2TB
FMC 1600 and 4600 1.2-TB drive (spare)FMC-M5-HDD-1.2TB=
FMC 2600 600-GB driveFMC-M5-HDD-600G
FMC 2600 600-GB drive (spare)FMC-M5-HDD-600G=
Rail kitUCSC-RAILB-M4
Power Cord Specifications
Each power supply has a separate power cord. Standard power cords or jumper power cords are available for
connection to the FMC 1600, 2600, and 4600. The jumper power cords for use in racks are available as an
optional alternative to the standard power cords.
If you do not order the optional power cord with the system, you are responsible for selecting the appropriate
power cord for the product. Using a incompatible power cord with this product may result in electrical safety
hazard. Orders delivered to Argentina, Brazil, and Japan must have the appropriate power cord ordered with
the system.
Only the approved power cords and jumper cords provided with the FMC 1600, 2600, and 4600 are supported.
Note
The following power cords and jumper cords are supported.
Figure 10: Argentina CAB-250V-10A-AR
Cord set rating: 10 A, 250 V2Plug: IRAM 20731
Connector: IEC 60320/C133
Cisco Firepower Management Center 1600, 2600, and 4600 Hardware Installation Guide
16
Overview
Power Cord Specifications