Cisco M195 Manual

Cisco Content Security Management Appliance M195, M395, M695,
and M695F Hardware Installation Guide
First Published: 2019-07-08
Last Modified: 2019-08-06
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,
INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,
CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of
the UNIX operating system. All rights reserved. Copyright ©1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.
CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network
topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional
and coincidental.
All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version.
Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com
go trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any
other company. (1721R)
©2019 Cisco Systems, Inc. All rights reserved.

CONTENTS
Overview 1
CHAPTER 1
Features 1
Package Contents 4
Serial Number Locations 4
Front Panel 6
Front Panel LEDs 8
Rear Panel 11
Rear Panel LEDs 14
Power Supply 15
Hardware Specifications 16
Product ID Numbers 17
Power Cord Specifications 18
Installation Preparation 27
CHAPTER 2
Installation Warnings 27
Safety Recommendations 28
Maintain Safety with Electricity 29
Prevent ESD Damage 29
Site Environment 30
Site Considerations 30
Power Supply Considerations 30
Rack Configuration Considerations 31
Rack-Mount the Chassis 33
CHAPTER 3
Unpack and Inspect the Chassis 33
Rack-Mount the Chassis 33
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
iii

Maintenance and Upgrade 37
CHAPTER 4
Power Button Shut Down 37
Enable RPC 38
Reset the Chassis Remotely 39
Install/Uninstall the Locking Faceplate 39
Remove and Replace a Drive 40
Remove and Replace a Power Supply 43
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
iv
Contents

CHAPTER 1
Overview
•Features, on page 1
•Package Contents, on page 4
•Serial Number Locations, on page 4
•Front Panel, on page 6
•Front Panel LEDs, on page 8
•Rear Panel, on page 11
•Rear Panel LEDs, on page 14
•Power Supply, on page 15
•Hardware Specifications, on page 16
•Product ID Numbers, on page 17
•Power Cord Specifications, on page 18
Features
The Cisco Content Security Management Appliances (SMA) M195, M395, M695, and M695F centralize
reporting, tracking, management of quarantined email messages, and web security appliance configuration
settings. They also allow automated data backups.
The SMA M195, M395, M695, and M695F support Cisco AsyncOS version 12.5 and later. See Product ID
Numbers, on page 17 for a list of field-replaceable product IDs (PIDs) associated with the SMA security
management appliances.
The following figures show the Cisco Content Security Appliances.
Figure 1: Cisco Content Security M195 and M395
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
1

Figure 2: Cisco Content Security M695 and M695F
The following table lists the features of the SMA M195, M395, M695, and M695F.
Table 1: SMA M195, M395, M695, and M695F Features
M695FM695M395M195Feature
2 RU1 RUForm factor
Standard 19-in. (48.3 cm) 4-post EIA rackRack mount
Front to rear
Cold aisle to hot aisle
Airflow
Displays the serial numberPullout asset card
Two threaded holes for dual-hole grounding lug
Use is optional; the supported AC power supplies have internal grounding, so no
additional chassis grounding is required.
Grounding holes
OptionalLocking faceplate
YesUnit identification
button
YesPower button
32-GB RAM
16-GB RAMMemory
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
2
Overview
Features

M695FM695M395M195Feature
Two 16-GB
Internal component only; not
field-replaceable
One 16-GB
Internal component only; not
field-replaceable
RDIMMs
One built-in port (MGMT)One built-in port
(DATA 1)
Management port
One Gigabit
Ethernet (DATA 1)
Two fiber optic
(DATA 2 and
DATA 3)
Five Gigabit Ethernet (DATA 1, DATA
2, DATA 3, DATA 4, DATA 5)
One Gigabit
Ethernet (DATA 2)
Network ports
Accessed through the 1-Gb dedicated portRemote power
cycling (RPC)
Two
USB 3.0 Type A
USB ports
Two fiber optic
NoSFP+ ports
GLC-SX-MMD (1
Gb) (optional)
SFP-10G-SR (10
Gb) (optional)
—Supported SFP+
One 1-Gb RJ-45 serial port running RS-232 (RS-232D TIA-561)
Directly connects a computer to the chassis
Serial console port
Two
1050-W AC
Hot-swappable and redundant as 1+1
Two
770-W AC
Hot-swappable and
redundant as 1+1
One
770-W AC
You can order a
second power
supply for
redundancy as 1+1.
AC power supply
Do not
mix
power
supply
type or
wattage
between
models.
Note
Six fans for front-to-rear cooling
Internal component only; not field-replaceable. If one fan fails, you must send your
chassis for RMA.
Fans
Sixteen 600-GB SAS HDDs
RAID 10, hot-swappable
Eight 600-GB SAS
HDDs
RAID 10,
hot-swappable
Two 600-GB SAS
HDDs
RAID 1,
hot-swappable
Storage
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
3
Overview
Features

Package Contents
The following figure shows the package contents for the SMA M195, M395, M695, and M695F. Note that
the contents are subject to change and your exact contents might contain additional or fewer items.
Figure 3: Package Contents
RJ-45 to DB9-RS232 console cable (Cisco part
number 72-3383-XX)
2Chassis1
RJ-45 to RJ-45 Cat 5 Ethernet cable, yellow six
feet long (Cisco part number 72-1482-XX)
4Cisco rail kit (Cisco part number 800-43376-02)3
Two 1-Gb or 10-Gb SFP+ fiber optic transceivers
with cables
Supported on the M695F. You cannot
mix SFP transceiver types in the same
chassis. You can either have two 1-Gb
or two 10-Gb SFPs in the same
chassis.
Note
6Useful Links document
The steps in the Useful Links document send you
to the documentation you need to install, set up,
and configure your SMA appliance.
5
Serial Number Locations
The serial number (SN) for the SMA M195, M395, M695, and M695F is printed on the pullout asset card
located on the front panel as shown in the following figure.
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
4
Overview
Package Contents

Figure 4: Serial Number on Pullout Asset Card
The serial number is also on the label on the cover of the chassis as shown in the following figure.
The cover latch on the top of the chassis cover is not supported. There are no internal field-replaceable parts
in the SMA M195, M395, M695, and M695F.
Caution
Figure 5: Serial Number Location on Cover
Cover latch
Not supported
2Serial number label1
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
5
Overview
Serial Number Locations

Front Panel
The following figure shows the front panel features and disk-drive configuration for the SMA M195. See
Front Panel LEDs, on page 8 for a description of the LEDs.
Figure 6: M195 Front Panel
Power button/power status LED2Drive bays
Supports two 600-GB SAS HDDs in slots 1 and
2
1
System status LED4Unit identification button/LED3
Fan status LED6Power supply status LED5
Temperature status LED8Network link activity LED7
Pullout asset card9
The following figure shows the front panel features and disk-drive configuration for the SMA M395. See
Front Panel LEDs, on page 8 for a description of the LEDs.
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
6
Overview
Front Panel

Figure 7: M395 Front Panel
Power button/power status LED2Drive bays
Supports eight 600-GB SAS HDDs in slots 1
through 8
1
System status LED4Unit identification button/LED3
Fan status LED6Power supply status LED5
Temperature status LED8Network link activity LED7
Pullout asset card9
The following figure shows the front panel features and disk-drive configuration for the SMA M695 and
M695F. See Front Panel LEDs, on page 8 for a description of the LEDs.
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
7
Overview
Front Panel

Figure 8: M695 and M695F Front Panel
Power button/power status LED2Drive bays
Supports sixteen 600-GB SAS HDDs in slots 1
through 16
1
System status LED4Unit identification button/LED3
Temperature status LED6Fan status LED5
Network link activity LED8Power supply status LED7
Pullout asset card9
Front Panel LEDs
The following figure shows the front panel LEDs for the M195, M395, M695, and M695F, and describes
their states.
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
8
Overview
Front Panel LEDs

Figure 9: Front Panel LEDs and Their States
Drive activity LED:
• Off—There is no drive in the drive tray (no
access, no fault).
• Green—The drive is ready.
• Green, flashing—The drive is reading or
writing data.
2Drive fault LED:
• Off—The drive is operating properly.
• Amber—Drive fault detected.
• Amber, flashing—The drive is rebuilding.
• Amber, flashing with 1-second
interval—Drive locate function activated in
the software.
1
Unit identification LED:
• Off—The unit identification function is not
in use.
• Blue, flashing—The unit identification
function is activated.
4Power LED:
• Off—There is no AC power to the chassis.
• Amber—The chassis is in standby mode.
• Green—The chassis is in main power mode.
Power is supplied to all components.
3
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
9
Overview
Front Panel LEDs

Power supply status LED:
• Green—All power supplies are operating
normally.
• Amber—One or more power supplies are in
a degraded operational state.
• Amber, flashing—One or more power
supplies are in a critical fault state.
6System status LED:
• Green—The chassis is running in normal
operating condition.
• Green, flashing—The chassis is performing
system initialization and memory check.
• Amber—The chassis is in a degraded
operational state (minor fault).
• Power supply redundancy is lost.
• CPUs are mismatched.
• At least one CPU is faulty.
• At least one DIMM is faulty.
• At least one drive in a RAID
configuration failed.
• Amber, 2 flashes—There is a major fault
with the system board.
• Amber, 3 flashes—There is a major fault
with the DIMMs.
• Amber, 4 flashes—There is a major fault
with the CPUs.
5
Network link activity LED:
• Off—The Ethernet port link is idle.
• Green—One or more Ethernet ports are
link-active, but there is no activity.
•Green, flashing—One or more Ethernet ports
are link-active with activity.
8Fan status LED:
• Green—All fans are operating properly.
• Amber, flashing—One or more fans
breached the nonrecoverable threshold.
7
Temperature status LED:
• Green—The chassis is operating at normal
temperature.
• Amber—One or more temperature sensors
breached the critical threshold.
• Amber, flashing—One or more temperature
sensors breached the nonrecoverable
threshold.
9
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
10
Overview
Front Panel LEDs

Rear Panel
The following figure shows the rear panel of the SMA M195. See Rear Panel LEDs, on page 14 for a
description of the LEDs.
Figure 10: M195 Rear Panel
USB 3.0 Type A (USB 2)2USB 3.0 Type A (USB 1)1
Data interface (DATA 2)4Management interface (DATA 1)3
Serial console port (Console)
RJ-45 connector that directly connects
a computer to the appliance.
6RPC port (RPC)5
One 770-W AC power supply
You can order a second power supply
to provide redundancy as 1 + 1.
8Unit identification button7
Riser handle
Not supported
10Threaded holes for dual-hole
grounding lug
Use is optional; the supported AC
power supplies have internal
grounding, so no additional chassis
grounding is required.
9
The following figure shows the rear panel of the SMA M395. See Rear Panel LEDs, on page 14 for a
description of the LEDs.
Figure 11: M395 Rear Panel
USB 3.0 Type A (USB 2)2USB 3.0 Type A (USB 1)1
Data interface (DATA 5)4Management interface (MGMT)3
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
11
Overview
Rear Panel

Serial console port (Console)
RJ-45 connector that directly connects
a computer to the appliance.
6RPC port (RPC)5
770-W AC power supply (PSU 1)8Unit identification button7
Threaded holes for dual-hole
grounding lug
Use is optional; the supported AC
power supplies have internal
grounding, so no additional chassis
grounding is required.
10770-W AC power supply (PSU 2)9
Data interface (DATA 2)12Data interface (DATA 1)11
Data interface (DATA 4)14Data interface (DATA 3)13
Riser handle
Not supported
15
The following figure shows the rear panel of the SMA M695. See Rear Panel LEDs, on page 14 for a
description of the LEDs.
Figure 12: M695 Rear Panel
Data interface (DATA 2)2Data interface (DATA 1)1
Data interface (DATA 4)4Data interface (DATA 3)3
1050-W AC power supply (PSU 2)61050-W AC power supply (PSU1)5
USB 3.0 Type A (USB 1)8Threaded holes for dual-hole
grounding lug
Use is optional; the supported AC
power supplies have internal
grounding, so no additional chassis
grounding is required.
7
Management interface (MGMT)10USB 3.0 Type A (USB 2)9
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
12
Overview
Rear Panel

RPC port (RPC)12Data interface (DATA 5)11
Unit identification button14Serial console port (Console)
RJ-45 connector that directly connects
a computer to the appliance.
13
The following figure shows the rear panel of the SMA M695F. See Rear Panel LEDs, on page 14 for a
description of the LEDs.
Figure 13: M695F Rear Panel
Data interface (DATA 3)
1/10-Gigabit SFP+ fiber optic support
Use only Cisco-supported SFP+
transceivers.
2Data interface (DATA 2)
1/10-Gigabit SFP+ fiber optic support
Use only Cisco-supported SFP+
transceivers.
1
1050-W AC power supply (PSU 2)41050-W AC power supply (PSU 1)3
USB 3.0 Type A (USB 1)6Threaded holes for dual-hole
grounding lug
Use is optional; the supported AC
power supplies have internal
grounding, so no additional chassis
grounding is required.
5
Management interface (MGMT)8USB 3.0 Type A (USB 2)7
RPC port (RPC)10Data interface (DATA 1)9
Unit identification button12Serial console port (Console)
RJ-45 connector that directly connects
a computer to the appliance.
11
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
13
Overview
Rear Panel

Rear Panel LEDs
The following figure shows the rear panel LEDs of the SMA M195 model and describes the LED states. The
M395, M695, and M695F have the same LEDs except that these models have more data interfaces; the speed
and status LED descriptions are the same.
Figure 14: Rear Panel LEDs and Their States
Management interface link status:
• Off—No link is present.
• Green—Link is active.
• Green, flashing—Traffic is
present on the active link.
2Management interface link speed:
• Off—Link speed is 100 Mbps.
• Amber—Link speed is 1 Gbps.
• Green—Link speed is 10 Gbps.
1
Data interface link status:
• Off—No link is present.
• Green—Link is active.
• Green, flashing—Traffic is
present on the active link.
4Data interface link speed:
• Off—Link speed is 10 Mbps.
•Amber—Link speed is 100 Mbps.
• Green—Link speed is 1 Gbps.
3
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
14
Overview
Rear Panel LEDs

Power supply (one LED for each
power supply):
• Off—No AC input (12-V main
power off; 12-V standby power
off)
• Green, flashing—12-V main
power off; 12-V standby power
on.
• Green—12-V main power on;
12-V standby power on.
• Amber, flashing—Warning
threshold detected but 12-V main
power on.
• Amber—Critical error detected;
12-V main power off ( for
example, overcurrent,
overvoltage, or overtemperature
failure).
6Rear unit identification:
• Off—The unit identification
function is not in use.
• Blue, flashing—The unit
identification function is
activated.
5
Power Supply
The following table lists the specifications for the 770-W AC power supply (Cisco part number 341-0591-04)
used in the SMA M195 and M395.
Table 2: 770-W Power Supply Specifications
SpecificationDescription
Nominal range: 100 to 120 V AC, 200 to 240 V AC
Range: 90–132 V AC, 180–264 V AC
AC input voltage range
Nominal range: 50–60 Hz
Range: 47–63 Hz
AC input frequency
9.5 A peak at 100-V AC
4.5 A peak at 208 V AC
Maximum AC input current
950 VA at 100 V ACMaximum input volt amperes
770 WMaximum output power for each power supply
15 A (subcycle duration)Maximum inrush current
12 ms at 770 WMaximum hold-up time
12 V DCPower supply output voltage
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
15
Overview
Power Supply

SpecificationDescription
12 V DCPower supply standby voltage
Climate Savers Platinum Efficiency (80 Plus Platinum
certified)
Efficiency rating
RSP2Form factor
IEC320 C13/C15Input connector
The following table lists the specifications for the 1050-W AC power supply (Cisco part number 341-0638-03)
used in the SMA M695 and 695F.
Table 3: 1050-W Power Supply Specifications
SpecificationDescription
Nominal range: 100 to 120 V AC, 200 to 240 V AC
Range: 90–132 V AC, 180–264 V AC
AC input voltage range
Nominal range: 50–60 Hz
Range: 47–63 Hz
AC input frequency
12.5 A peak at 100 V AC
6.0 A peak at 208 V AC
Maximum AC input current
1250 VA at 100 V ACMaximum input volt amperes
1050 WMaximum output power for each power supply
15 A (subcycle duration)Maximum inrush current
12 ms at 1050 WMaximum hold-up time
12 V DCPower supply output voltage
12 V DCPower supply standby voltage
Climate Savers Platinum Efficiency (80 Plus Platinum
certified)
Efficiency rating
RSP2Form factor
IEC320 C14Input connector
Hardware Specifications
The following table lists the hardware specifications for the SMA M195, M395, M695, and M695F.
Cisco Content Security Management Appliance M195, M395, M695, and M695F Hardware Installation Guide
16
Overview
Hardware Specifications