Cisco 2811 Series Instruction Manual

Corporate Headquarters:
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Installing and Upgrading Fans in Cisco 2811
Series Routers
This document describes how to install or upgrade fans that are located internally within a Cisco 2811
series integrated services router. You need to remove the cover from the router to install or remove any
of these items. The document contains the following sections:
•Safety Warnings, page 1
•Removing the Chassis Cover, page 2
•Locating the Fan, page 5
•Installing and Removing the Fans, page 5
•Installing the Chassis Cover, page 13
Before you begin the fan replacement procedure, disconnect the power and remove the cover, as
described in the “Removing the Chassis Cover” section on page 2. After you complete the fan
replacement procedure, install the chassis cover as described in the “Installing the Chassis Cover”
section on page 13.
Safety Warnings
Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.
Statement 1

2
Installing and Upgrading Fans in Cisco 2811 Series Routers
78-17850-01
Removing the Chassis Cover
Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.
Statement 1001
Warning Read the installation instructions before connecting the system to the power source. Statement 1004
Warning Before working on equipment that is connected to power lines, remove jewelry (including rings,
necklaces, and watches). Metal objects will heat up when connected to power and ground and can
cause serious burns or weld the metal object to the terminals. Statement 43
Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF
or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables,
detach the end away from the unit first. Statement 1026
Removing the Chassis Cover
Cisco 2811 series routers have a cover that lifts off after you slide it free from front panel.
Caution Do not, under any circumstances, tamper with or attempt to remove the safety shields protecting the
WIC/HWIC slots and connectors on the Cisco 2811 routers.
Removing the Cover from Cisco 2811 Routers
To remove the chassis cover for a Cisco 2811 series router, follow these steps. You will need a number
2 Phillips screwdriver and a flat-blade screwdriver with a blade width of 1/4 ± 1/32 inch (5 to 7 mm).
Rack-mounted routers must be removed from the rack and positioned on a flat surface before you start
removing the cover.
Caution To prevent damage to the chassis, follow this procedure to remove the cover. Do not pry on the plastic
bezel or on the ears at either side of the chassis on the back.
The following warning applies only if the router is provided with a DC power input:
Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit.
Statement 1003

3
Installing and Upgrading Fans in Cisco 2811 Series Routers
78-17850-01
Removing the Chassis Cover
Step 1 Make sure that the router is turned off and disconnected from its power source.
Warning Before opening the unit, disconnect the telephone-network cables to avoid contact with
telephone-network voltages. Statement 1041
Step 2 If rack-mounting brackets are attached to the chassis, remove them, using a Phillips screwdriver.
Step 3 Remove the four screws at the back of the top cover, using a Phillips screwdriver.
Step 4 Perform the following steps to loosen the cover from the chassis:
a. Insert the blade of the 1/4-inch screwdriver straight into the square hole on either side of the chassis
near the back, so that it fits against the chassis and does not go past the chassis and into the narrow
slot. See Figure 1.
Caution Make sure that the tip of the screwdriver does not slide into the narrow vertical slot that is visible inside
the square hole. The tip of the screwdriver should rest on the metal tab just inside the chassis cover and
to the right of the vertical slot.
Figure 1 Inserting the Screwdriver into the Side of the Chassis
b. With the screwdriver positioned as required in Step a. above, rotate the screwdriver a quarter turn
toward the back of the chassis to loosen one side of the cover. See Figure 2.
Caution The friction fit may be fairly tight; however, if the cover does not move with moderate effort, make sure
that the screwdriver is not inserted into the narrow vertical slot.
Figure 2 Rotating the Screwdriver to Loosen the Chassis Cover
c. Repeat Step a. and Step b. for the opposite side of the chassis.
103860
Screwdriver must not
enter the vertical slot
103861

4
Installing and Upgrading Fans in Cisco 2811 Series Routers
78-17850-01
Removing the Chassis Cover
The cover should now be positioned back from the bezel about 1/4 inch (6 to 7 mm). If it is not, repeat
Step a. and Step b. for one or both sides of the chassis.
Step 5 Slide the cover toward the back of the chassis until it contacts a stop (about 1 inch [25 mm]). The front
edge of the cover should be free. See Figure 3.
Note After the cover is loosened as in Step 4, there may still be some friction to overcome as you
complete the removal. However, do not use the screwdriver again as in Step 4.
Step 6 Lift the cover free of the router chassis.
Figure 3 Cisco 2811 Router—Cover in Position for Removal
103477
Plastic bezel
Approx. 1 inch
(25 mm)

5
Installing and Upgrading Fans in Cisco 2811 Series Routers
78-17850-01
Locating the Fan
Locating the Fan
Figure 4 shows the locations of the fans in a Cisco 2811 series router.
Figure 4 Fan Locations in Cisco 2811 Routers
Note The fan numbers in Figure 4 correllate to IOS show environment command numbers. The arrows
show proper air flow.
Installing and Removing the Fans
The router fans rest on the chassis base and have a wire that connects to the system board.
Before you remove or install a fan, remove the chassis cover as described in the “Removing the Chassis
Cover” section on page 2.
Caution When you remove or install a fan, always wear an ESD-preventive wrist strap, and ensure that it makes
good contact with your skin. Connect the equipment end of the wrist strap to the metal part of the chassis.
1System fan 2System fan
3Power supply fan
271118
2
1
3

6
Installing and Upgrading Fans in Cisco 2811 Series Routers
78-17850-01
Installing and Removing the Fans
Removing the System Fans
To remove a system fan, perform the following procedure. To complete this procedure, you may need a
flat-blade screwdriver.
Step 1 Locate the fans to be removed. See Figure 4 for the location of the fans.
Step 2 Disconnect the fan connector from the system board as shown in Figure 5.
Figure 5 Disconnecting the System Fan Connector from the System Board
Step 3 Remove the fan wire from the wire management clip, which is located on the chassis base as shown in
Figure 6.
Figure 6 Removing the Fan Wire from the Wire Management Clip
Step 4 Remove the fan by sliding it upward, and then tilting it toward the chassis wall as shown in Figure 8.
Note If the fan is difficult to grasp when sliding upward, use a flat-blade driver for leverage as shown
in Figure 7.
170494
170495

7
Installing and Upgrading Fans in Cisco 2811 Series Routers
78-17850-01
Installing and Removing the Fans
Figure 7 Using a Flat-Blade Screwdriver for Added Leverage When Removing the Fan
Figure 8 shows the fan being tilted away from the chassis to remove it.
Figure 8 Lifting and Tilting the Fan to Remove
Step 5 Place the fan in an antistatic bag to protect it from ESD damage.
170531
1Lift the fan upward 2Tilt the fan toward chassis
170498
21 2

8
Installing and Upgrading Fans in Cisco 2811 Series Routers
78-17850-01
Installing and Removing the Fans
Removing the Power Supply Fan
To remove the power supply fan, perform the following procedure. To complete this procedure, you may
need a flat-blade screwdriver.
Step 1 Locate the fan to be removed. See Figure 4 for the location of the fans.
Step 2 Disconnect the fan connector from the system board as shown in Figure 9.
Figure 9 Disconnecting the Power Supply Fan Connector
Step 3 Lift the ribbon cable to allow slack to remove the air baffle as shown in Figure 10.
Note It is not necessary to disconnect the ribbon cable from the CompactFlash printed circuit board
(PCB) or system board.
170510

9
Installing and Upgrading Fans in Cisco 2811 Series Routers
78-17850-01
Installing and Removing the Fans
Figure 10 Lifting the Ribbon Cable
Step 4 Remove the plastic air baffle by gently squeezing the air baffle sides, disengaging the baffle from the
chassis base as shown in Figure 11.
Figure 11 Removing the Air Baffle
Step 5 Remove the fan wire from the wire management clip, which is located on the chassis base as shown in
Figure 6.
Step 6 Remove the fan by placing a flat-blade screwdriver at the base of the plastic fan housing and lifting the
fan in a vertical position, as shown in Figure 12.
170511170512

10
Installing and Upgrading Fans in Cisco 2811 Series Routers
78-17850-01
Installing and Removing the Fans
Figure 12 Using a Flat-Blade Screwdriver to Lift the Fan
Step 7 Disengage the fan from the side attachment slots and push the fan toward the center of the chassis, and
remove the fan as shown in Figure 13.
Figure 13 Disengaging the Fan from the Side Attachment Slots
Step 8 Place the fan in an antistatic bag to protect it from ESD damage.
170513
170530