Cisco Linksys WET610N User manual

LINKSYS®by Cisco • I II • I II •
CISCO.
QUICK INSTALLATION GUIDE
Wireless-N Ethernet Bridge
with Dual-Band
Model: WET610N

WET610N
Installation .
Installation
•Insert the Setup Wizard CD into
your CD-ROM drive.
OlE: Windows or other
personal firewalls may
ask for permission to run
the software.
To continue,
allow the software
to run.
B. The Welcome screen appears.
Click Next.
c. Read the License Agreement.
To accept the terms in the
License Agreement, select I
accept this agreement.
Click Next.
D. For configuration, you will
temporarily connect the
Bridge
to your router. (After
configuration, you will connect
the Bridge
to the device
that you want to equip with
wireless.)
Click Next.
Wireless-N Ethernet Bridge with Dual-Band
Insert
the CD-ROM
3

Installation
E. Connect one end of the
included network cable
to the
Ethernet port
of the Bridge.
Click ext.
F. Connect the other end of
the cable to one of the local
network ports on your router.
Click Next.
G. Connect the included power
adapter
to the Power port of the
Bridge.
Click Next.
H. Plug the power cord into an
electrical outlet.
Click ext.
4
WET61ON
Wireless-N Ethernet Bridge with Dual-Band

WET61ON
•Wait until the Power and
Ethernet
LEDs a re solidIy Iit.
Click ext.
J. Enter apassword to protect
access to the Bridge.
Click Next.
K. The wireless setup is next.
Click Next.
L. The Setup Wizard displays
the Network Name of the
wireless network with the
strongest signal. To connect to
this network, click Next.Then
proceed
to step P.
To connect to a different
network, select Idon't want to
connect to this network, and
click Next.
Wireless-N Ethernet Bridge with Dual-Band
Installation
5

Installation WET61ON
"
•The available networks are
listed in
the table. Select your
network, and then click ext.
(Ifyour router supportsWi-Fi
Protected Setup, which
is
indicated by the icon next
to the network name, then
proceed
to the section, "Wi-Fi
Protected Setu
p':)
If your network is not listed, select My network is not in this list, and
click Next. Proceed
to step o.
• If your network does not use
wireless security, proceed to
step P.
If your network uses wireless
security, enter the security key
of your wireless network. Click
Next.Then proceed to step P.
O. Configure the following:
ireless et or arne
{SSID} Enter the name of your
wireless network.
Au hentication Type Select
the authentication used byyour
wireless network.
Encryp ion ype Select
the encryption used byyour
wireless network.
Security ey Enter the security key of your wireless network.
Click ext.
6
OTE: If you are connecting to your own wireless network, you
may
want to configure wireless security on your router if you
have
not already done so.
Wireless-N Ethernet Bridge with Dual-Band

WET61ON
Installation
P. Please wait whi e the Setup Wizard connects the Bridge to your wireless
network.Warnings from your firewall or security application may
appear.
If necessary, click Always a ow or Allow this time only to
allow the wireless connection.
Q. You will connect the Bridge
to the device that you want to
equip with wireless.
Click Next.
R. The Bridge is connected to your
router
with a network cable.
Disconnect this
network cable
from your router.
If you need to move the device
that you
want to equip with
wireless, then do so now. Click
ext.
s. Connect the free end of the
networkcable
to the device that
you want to equip with wireless.
If you need to move the Bridge,
then make sure you take the
power adapter and
network
cable with you.
Click Next.
Wireless-N Ethernet Bridge with Dual-Band 7

Installation
T. Wait until the Power and
Ethernet
LEDs are solidly lit, and
the Wireless LED is flash"ng.
Click ext.
u. The wireless settings are
displayed.
To save the settings in a text
file on your desktop, keep the
default, Save these settings in
a text f-Ie on my desktop.
Click Next.
v. The Bridge is installed. You can
move
the Bridge anywhere
within your wireless network's
range,
as long as you plug its
power cord into an electrical
outlet.
Refer
to the User Guide on the
CD-ROM for information about
advanced settings.
WET61ON
Congratulations! Setup is complete.
8Wireless-N Ethernet Bridge
with Dual-Band

WET61ON
Wi-Fi Protected Setup
Wi-Fi Protected Setup
Wi-Fi Protected Setup Button on Router
A. Use Wi-Fi Protected Setup to
create awireless connection
between the Bridge and your
router.
On your router, press the
button that looks like one of the
icons in
the picture. You may
have
to hold down this button
until
an LED flashes.
Within
two minutes, click
Connect on the QuicklyConnect
Using Push Button screen.
(el
~)
B. Please wait while the Setup Wizard connects the Bridge to your wireless
network.Warnings from your firewall
or security application may
appear.
If necessary, click Always allow or Allow this time only to .
allow the wireless connection.
c. You will connect the Bridge
to the device that you want to
equip with wireless.
Click ext.
D. The Bridge is connected to your
router
with anetworkcable.
Disconnect this networkcable
from your router.
Ifyou need
to move the device
that you want to equip with
wireless, then
do so now. Click
Next.
Wireless-N Ethernet Bridge with Dual-Band 9

Wi-Fi Protected Setup
E. Connect the free end of the
network cable to the device that
you want to equip with wireless.
If you need to move the Bridge,
then make sure you take the
power adapter and
network
cable with you.
Click ext.
•Wait until the Power and
Ethernet
LEDs are solidly lit, and
theWireless
LED is flashing.
Click Next.
G. The wireless settings are
displayed.
To save the settings in a text
file on your desktop, keep the
default, Save
these settings in
a text file on my desktop.
Click Next.
WET61ON
H. The Bridge is installed. You can
move the Bridge anywhere
within your wireless network's
range,
as long as you plug its
power cord
into an electrical
outlet.
Refer to the User Guide on the
CD-ROM for information about
advanced settings.
Congratulations! Set p is complete. 8121810NC-JL
10 Wireless-N Ethernet Bridge
with Dual-Band