Cisco APP1000 - One Application Server Appliance Instruction Manual

Installation and Administration Guide
Model: APP1000
Linksys One Application Server
Appliance

Linksys One Application Server Appliance
i
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . 1
Front Panel . . . . . . . . . . . . . . . . . . . . . . . 2
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . 3
Wall Mounting . . . . . . . . . . . . . . . . . . . . . 4
Cable Installation . . . . . . . . . . . . . . . . . . . . 5
Administration . . . . . . . . . . . . . . . . . . . . . 6
Specifications . . . . . . . . . . . . . . . . . . . . . . 7
Safety Information . . . . . . . . . . . . . . . . . . . 9
License Agreement . . . . . . . . . . . . . . . . . . 11
Limited Warranty . . . . . . . . . . . . . . . . . . . 12

Linksys One Application Server Appliance
ii

Linksys One Application Server Appliance
1
1
Introduction
Congratulations on your purchase of an APP1000 Application Server
Appliance. You will improve productivity and enable centrally
managed, robust features such as Interactive Video Surveillance. New
applications will leverage the APP1000 to introduce new features and
functionality.
The APP1000 application server appliance enables the deployment
of Linksys One applications for Linksys One networks. It features a
500 MHz ARM-based processor with 256 MB of RAM, 512 MB of FLASH,
a single 10/100 Ethernet port, and a USB 2.0 host port. The Ethernet
port is IEEE 802.3af PoE capable allowing the application server
appliance to be powered by a PoE switch.
We hope you enjoy your new productivity.

Linksys One Application Server Appliance
2
Front Panel
LED Off Solid Blinking or Flashing
POWER No power Power
present
n/a
DIAG n/a n/a Downloading software image
ETHERNET No link Link
established
Incoming/outgoing traffic
USB* n/a n/a n/a
FLASH No activity n/a Read/write activity
2
* Reserved for future use.

Linksys One Application Server Appliance
3
Rear Panel
Name Description
Power 48-VDC power port (only use Power Cube AC to 48-VDC
power adapter, part number CP-PWR-CUBE-3).
ETHERNET Ethernet port, supports Power over Ethernet (IEEE 802.3af
PoE).
USB Reserved for future use.
RESET Reset button.
Press for 1 to 5 seconds to reset the APP1000.
Press for 6 to 14 seconds to restore the application data
(software) to default values.
Press for 15 seconds or more to reset the APP1000 to its
factory default settings.
•
•
•
3

Linksys One Application Server Appliance
4
4Wall Mounting
The APP1000 is designed to rest on a flat surface. Optionally, it can be
wall mounted in either a front-side-up or left-side-up configuration.
Mounting screws are not supplied; recommended screw head diameter
is 6mm to 8mm (0.2362 in to 0.3149 in). In the image, the front-side-
up mounting holes are indicated by circles; the left-side-up mounting
holes are indicated by triangles. Screw spacing for front-side-mounting
is 150 mm (5.9055 in); for left-side-up mounting, the spacing is 108 mm
(4.2519 in).
Install mounting screws according to the mounting configuration
that you selected. Use appropriate wall anchors to secure the
screws.
Align the mounting holes on the bottom of the APP1000 to the
wall-mounted screws and slide down.
Verify that the APP1000 is securely attached to the wall.
A.
B.
C.

Linksys One Application Server Appliance
5
Cable Installation
The APP1000 can be connected directly to either a Linksys One
Services Router (SVR) or to a Linksys One Ready Ethernet Switch that is
connected to an SVR.
Connect an ethernet cable
from the ETHERNET port to
an SVR or to a Linksys One
Ready Switch.
Verify that the POWER and
ETHERNET indicators light
on the front panel.
(Optional) If the Ethernet
Switch that you connected
to the Application Server
does not supply power via
the ethernet cable (802.3af
PoE), connect power to the
Power port with a Cisco
Power Cube 3 (AC to 48-
VDC power adapter, part
number CP-PWR-CUBE-3).
For further details on installing Linksys One products, refer to the
Linksys One Communications Solution Quick Installation Guide.
A.
B.
C.


5

Linksys One Application Server Appliance
6
The APP1000 is configured through the Linksys One Administrator
portal (refer to the Linksys One Customer Premises Equipment
Administration Guide for details on using the Linksys One Administrator
portal). You can check the status of the APP1000 via the Install >
Applications screen or you can restart the application, reboot the
APP1000, or power cycle it via the Support View > Devices screen.
To view the status of the
APP1000, click the Install tab
and the Applications tab. A
status screen opens showing
this information:
Location—Text label indicating the physical location of the APP1000.
IP—Internet Protocol (IP) and Media Access Control (MAC) address of
the APP1000.
Initialization—The status of the initialization process.
Last started—The time since the APP1000 was last started.
Use—Name of the application running on the APP1000.
To restart the application
running on the APP1000, click
the Support View tab and
click Devices. A screen opens
showing the attached devices.
From this screen you can:
Restart App—Restarts the current application running on the
APP1000.
Reboot—Reboots the APP1000, same as pressing the reset button 1 to
5 seconds.
Power Cycle—Cycles the power to the APP1000, same as momentarily
removing power from the APP1000.
Administration
6