Cisco MSE 3365 User manual

CHAPTER
1-1
Cisco MSE 3365 Installation Guide
1
Overview
This guide provides step-by-step instructions on how to physically install and power up the Cisco 3365
Mobility Services Engine (MSE). Details on running the automatic installation script is also provided.
This chapter contains the following sections:
•External Features Overview, page 1-1
•Status LEDs and Buttons, page 1-3
•General Warnings, Regulatory and Safety, page 1-8
External Features Overview
The Cisco MSE 3365 comes with four Small form factor (SFF) drives. See Figure 1-1.

1-2
Cisco MSE 3365 Installation Guide
Chapter 1 Overview
External Features Overview
Figure 1-1 shows the front panel of the Cisco MSE 3365.
Figure 1-1 Cisco MSE 3365 Front Panel
1Drive bays 1–8 support SAS/SATA
drives) 7System status LED
2Drive bays 1 and 2 support
SAS/SATA and NVMe PCIe solid
state drives (SSDs)
8Fan status LED
3Pull-out asset tag 9Temperature status LED
4Operations panel buttons and LEDs 10 Power supply status LED
5Power button/power status LED 11 Network link activity LED
6Unit identification button/LED 12 KVM connector (used with KVM cable that provides
two USB 2.0, one VGA, and one serial connector)
1197
5 6 8 10
352973
HDD 02
HDD 01 HDD 03
HDD 04 HDD 05 HDD 06 HDD 08 HDD 07
3
4
2
1
12

1-3
Cisco MSE 3365 Installation Guide
Chapter 1 Overview Status LEDs and Buttons
Figure 1-2 shows the rear panel of the Cisco MSE 3365.
Figure 1-2 Cisco MSE 3365 Rear Panel
Status LEDs and Buttons
This section describes the location and meaning of LEDs and buttons and includes the following topics
•Front Panel LEDs, page 1-3
•Rear Panel LEDs and Buttons, page 1-6
Front Panel LEDs
Figure 1-3 shows the front panel LEDs. Table 1-1 defines the LED states.
1PCIe riser 1/slot 1 (not used) 7Serial port (RJ-45 connector)
2PCIe riser 2/slot 2 (not used) 8Dual 1-Gb Ethernet ports (LAN1 and LAN2).
Port 1 is normally used by the Cisco MSE
(eth0) for communication with the Cisco
Wireless LAN Controllers and Cisco Prime
Infrastructure.
3Modular LAN-on-motherboard (mLOM) card
slot (not used) 9VGA video port (DB-15)
4Grounding-lug hole (for DC power supplies) 10 Rear unit identification button/LED
5USB 3.0 ports (two) 11 Power supplies (two, redundant as 1+1)
61-Gb Ethernet dedicated management port
352977
mLOM
PCIe 01 PCIe 02
PSU 01 PSU 02
1 2
3 6 7 9 108 11
5
4
21

1-4
Cisco MSE 3365 Installation Guide
Chapter 1 Overview
Status LEDs and Buttons
Figure 1-3 Front Panel LEDs
1Hard drive fault LED 6Fan status LED
2Hard drive activity LED 7Temperature status LED
3Power button/power status LED 8Power supply status LED
4Identification button/LED 9Network link activity LED
5System status LED
Table 1-1 Front Panel LEDs, Definitions of States
LED Name State
1Hard drive fault •Off—The hard drive is operating properly.
•Amber—Drive fault detected.
•Amber, blinking—The device is rebuilding.
•Amber, blinking with one-second interval—Drive locate function activated.
2Hard drive activity •Off—There is no hard drive in the hard drive tray (no access, no fault).
•Green—The hard drive is ready.
•Green, blinking—The hard drive is reading or writing data.
3Power button/LED •Off—There is no AC power to the Cisco MSE 3365.
•Amber—Cisco MSE 3365 is in standby power mode. Power is supplied only to the
Cisco IMC and some motherboard functions.
•Green—Cisco MSE 3365 is in main power mode. Power is supplied to all the MSE
3365 components.
4Unit identification •Off—The unit identification function is not in use.
•Blue—The unit identification function is activated.
353088
975
3 4 6 8
BAY 02
BAY 01 BAY 03
BAY 04 BAY 05 BAY 06 BAY 08 BAY 07
21

1-5
Cisco MSE 3365 Installation Guide
Chapter 1 Overview Status LEDs and Buttons
5System status •Green—Cisco MSE 3365 is running in normal operating condition.
•Green, blinking—Cisco MSE 3365 is performing system initialization and memory
check.
•Amber, steady—Cisco MSE 3365 is in a degraded operational state. For example:
– Power supply redundancy is lost.
– CPUs are mismatched.
– At least one CPU is faulty.
– At least one DIMM is faulty.
– At least one drive in a RAID configuration failed.
•Amber, blinking—Cisco MSE 3365 is in a critical fault state. For example:
– Boot failed.
– Fatal CPU and/or bus error is detected.
– Cisco MSE 3365 is in an over-temperature condition.
6Fan status •Green—All fan modules are operating properly.
•Amber, steady—One or more fan modules breached the critical threshold.
•Amber, blinking—One or more fan modules breached the non-recoverable
threshold.
7Temperature status •Green—Cisco MSE 3365 is operating at normal temperature.
•Amber, steady—One or more temperature sensors breached the critical threshold.
•Amber, blinking—One or more temperature sensors breached the non-recoverable
threshold.
8Power supply status •Green—All power supplies are operating normally.
•Amber, steady—One or more power supplies are in a degraded operational state.
•Amber, blinking—One or more power supplies are in a critical fault state.
9Network link activity •Off—The Ethernet link is idle.
•Green—One or more Ethernet LOM ports are link-active, but there is no activity.
•Green, blinking—One or more Ethernet LOM ports are link-active, with activity.
Table 1-1 Front Panel LEDs, Definitions of States (continued)
LED Name State

1-6
Cisco MSE 3365 Installation Guide
Chapter 1 Overview
Status LEDs and Buttons
Rear Panel LEDs and Buttons
Figure 1-4 shows the rear panel LEDs and buttons. Table 1-2 defines the LED states.
Figure 1-4 Rear Panel LEDs and Buttons
1Optional mLOM card LEDs.
Note This LED is not applicable for Cisco
MSE 3365.
51-Gb Ethernet link status LED
21-Gb Ethernet dedicated management link
status LED 6Rear unit identification button/LED
31-Gb Ethernet dedicated management link
speed LED 7Power supply status LED
41-Gb Ethernet link speed LED
Table 1-2 Rear Panel LEDs, Definitions of States
LED Name State
21-Gb Ethernet dedicated
management link speed •Off—Link speed is 10 Mbps.
•Amber—Link speed is 100 Mbps.
•Green—Link speed is 1 Gbps.
31-Gb Ethernet dedicated
management link status •Off—No link is present.
•Green—Link is active.
•Green, blinking—Traffic is present on the active link.
41-Gb Ethernet link speed •Off—Link speed is 10 Mbps.
•Amber—Link speed is 100 Mbps.
•Green—Link speed is 1 Gbps.
51-Gb Ethernet link status •Off—No link is present.
•Green—Link is active.
•Green, blinking—Traffic is present on the active link.
353089
mLOM
PCIe 01 PCIe 02
PSU 01 PSU 02
1 32 5 6 74
12

1-7
Cisco MSE 3365 Installation Guide
Chapter 1 Overview Status LEDs and Buttons
6Rear unit identification •Off—The unit identification LED is not in use.
•Blue—The unit identification LED is activated.
7Power supply status AC power supplies:
•Off—No AC input (12 V main power off, 12 V standby power off).
•Green, blinking—12 V main power off; 12 V standby power on.
•Green, solid—12 V main power on; 12 V standby power on.
•Amber, blinking—Warning detected but 12 V main power on.
•Amber, solid—Critical error detected; 12 V main power off.
Table 1-2 Rear Panel LEDs, Definitions of States (continued)
LED Name State

1-8
Cisco MSE 3365 Installation Guide
Chapter 1 Overview
General Warnings, Regulatory and Safety
General Warnings, Regulatory and Safety
Conventions
Safety warnings appear throughout this guide in procedures that may harm you if performed incorrectly.
A warning symbol precedes each warning statement. Specific warnings are included in the sections to
which they apply.
Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
eachwarningtolocateitstranslationinthetranslatedsafetywarningsthataccompaniedthisdevice.
Statement 1071 SAVE THESE INSTRUCTIONS
Caution Means reader be careful. In this situation, you might do something that could result in equipment damage
or loss of data.
Warnings
The warnings below are general warnings that are applicable to the entire guide. Specific warnings are
included in the sections to which they apply.
Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with
the same or equivalent type recommended by the manufacturer. Dispose of used batteries according
to the manufacturer’s instructions. Statement 1015
Warning This equipment must be grounded. Neverdefeat the ground conductor oroperate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024
Warning Read the installation instructions before connecting the system to the power source. Statement 1004
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040

1-9
Cisco MSE 3365 Installation Guide
Chapter 1 Overview General Warnings, Regulatory and Safety
Regulatory and Safety
Note Refer to Appendix A for translated safety information for the Cisco 3365 Mobility Services Engine.
Note Refer to Appendix B for regulatory information for the Cisco 3365 Mobility Services Engine.

1-10
Cisco MSE 3365 Installation Guide
Chapter 1 Overview
General Warnings, Regulatory and Safety