Cisco MDS 9100 Series Manual

CHAPTER
Send documentation comments to [email protected]
2-1
Cisco MDS 9100 Series Hardware Installation Guide
OL-21514-01
2
Installing the Cisco MDS 9100 Series
This chapter describes how to install the Cisco MDS 9100 Series and its components, and it includes the
following information:
•Preinstallation, page 2-2
•Installing the Switch in a Cabinet or Rack, page 2-5
•Installing the Switch in a Cabinet with Insufficient Front Clearance, page 2-11
•Installing Cisco MDS 9134 48-Port and 64-Port Bundles, page 2-21
•Grounding the Switch, page 2-23
•Starting Up the Switch, page 2-24
•Removing and Installing Components, page 2-25
Note Before you install, operate, or service the system, read the Regulatory Compliance and Safety
Information for the Cisco MDS 9000 Family for important safety information.

Send documentation comments to [email protected]
2-2
Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01
Chapter 2 Installing the Cisco MDS 9100 Series
Preinstallation
Warning IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before
you work on any equipment, be aware of the hazards involved with electrical circuitry and be
familiar with standard practices for preventingaccidents. Use the statement number provided at
the end of each warning to locate its translation in the translated safety warnings that
accompanied this device.
Statement 1071
SAVE THESE INSTRUCTIONS
Warning This unit is intended for installation in restricted access areas. A restricted access area can be
accessed only through the use of a special tool, lock and key, or other means of security.
Statement 1017
Warning Only trained and qualified personnel should be allowed to install, replace, or service
this equipment. Statement 1030
Note Each new switch requires a license; see the Cisco MDS 9000 Family NX-OS Licensing Guide for
instructions on installing a license.
Preinstallation
This section includes the following information:
•Installation Options, page 2-2
•Installation Guidelines, page 2-3
•Required Equipment, page 2-4
•Unpacking and Inspecting the Switch, page 2-4
Installation Options
The Cisco MDS 9100 Series can be installed using the following methods:
•In an open EIA rack, using:
– The rack-mount kit shipped with the switch
– The telco and EIA Shelf Bracket Kit (an optional kit, purchased separately) in addition to the
rack-mount kit shipped with the switch
•In a perforated or solid-walled EIA cabinet, using:
– The rack-mount kit shipped with the switch
– The telco and EIA Shelf Bracket Kit (an optional kit, purchased separately) in addition to the
rack-mount kit shipped with the switch

Send documentation comments to [email protected]
2-3
Cisco MDS 9100 Series Hardware Installation Guide
OL-21514-01
Chapter 2 Installing the Cisco MDS 9100 Series Preinstallation
•In a two-post telco rack, using:
– The telco and EIA Shelf Bracket Kit (an optional kit, purchased separately) in addition to the
front brackets shipped with the switch
For instructions on installing the switch using the rack-mount kit shipped with the switch, see
the“Installing the Switch in a Cabinet or Rack” section on page 2-5.
For instructions on installing the switch using the optional, separately purchased telco and EIA Shelf
Bracket Kit, see the “Cisco MDS 9000 Family Telco and EIA Shelf Bracket” section on page A-3.
Note The telco and EIA Shelf Bracket Kit is optional and is not provided with the switch. To order the kit,
contact your switch provider.
Installation Guidelines
Follow these guidelines when installing the Cisco MDS 9100 Series:
•Plan your site configuration and prepare the site before installing the switch. The recommended site
planning tasks are listed in Appendix D, “Site Planning and Maintenance Records.”
•Ensure there is adequate space around the switch to allow for servicing the switch and for adequate
airflow (airflow requirements are listed in Appendix B, “Technical Specifications”).
•Ensure the air-conditioning meets the heat dissipation requirements listed in Appendix B,
“Technical Specifications.”
•Ensure the cabinet or rack meets the requirements listed in Appendix A, “Cabinet and Rack
Installation.”
Note If the front cabinet mounting rails are not offset from the front door or bezel panel by a minimum
of 3 in. (7.6 cm), and a minimum of 5 in. (12.7 cm) if cable management brackets are installed
on the front of the chassis, the chassis should be mounted rear-facing to ensure the minimum
bend radius for fiber-optic cables. See the“Installing the Switch in a Cabinet with Insufficient
Front Clearance” section on page 2-11.
Note Jumper power cords are available for use in a cabinet. For more information, see the “Jumper
Power Cord” section on page C-6.
•Ensure the chassis is adequately grounded. If the switch is not mounted in a grounded rack, we
recommend connecting both the system ground on the chassis and the power supply ground to an
earth ground.
•Ensure the site power meets the power requirements listed in Appendix B, “Technical
Specifications.” If available, you can use an uninterruptible power supply (UPS) to protect against
power failures.
Caution Avoid UPS types that use ferroresonant technology. These UPS types can become unstable
with systems such as the Cisco MDS 9000 Family, which can have substantial current draw
fluctuations because of fluctuating data traffic patterns.

Send documentation comments to [email protected]
2-4
Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01
Chapter 2 Installing the Cisco MDS 9100 Series
Preinstallation
•Ensure that circuits are sized according to local and national codes.
For North America, the 300-W power supplies require a 20-A circuit. If you are using a 200- or
240-VAC power source in North America, the circuit must be protected by a two-pole circuit
breaker.
Caution To prevent loss of input power, ensure the total maximum loads on the circuits supplying
power to the switch are within current ratings for wiring and breakers.
•As you install and configure the switch, record the information listed in the “Site Planning and
Maintenance Records” section on page D-1.
•Use the following screw torques when installing the switch:
– Captive screws: 4 in-lb
– M3 screws: 4 in-lb
– M4 screws: 12 in-lb
– 10-32 screws: 20 in-lb
– 12-24 screws: 30 in-lb
Required Equipment
Gather the following tools before beginning the installation:
•Number 1 Phillips screwdriver with torque capability
•3/16-in. flat-blade screwdriver
•Tape measure and level
•ESD wrist strap or other grounding device
•Antistatic mat or antistatic foam
The following additional items (not found in the accessory kit) are required to ground the chassis:
•Grounding cable (6 AWG recommended), sized according to local and national installation
requirements; the required length depends on the proximity of the switch to proper grounding
facilities
•Crimping tool large enough to accommodate girth of lug
•Wire-stripping tool
Unpacking and Inspecting the Switch
Caution When handling switch components, wear an ESD strap and handle modules by the carrier edges only.
An ESD socket is provided on the chassis. For the ESD socket to be effective, the chassis must be
grounded through the power cable, the chassis ground, or the metal-to-metal contact with a grounded
rack.

Send documentation comments to [email protected]
2-5
Cisco MDS 9100 Series Hardware Installation Guide
OL-21514-01
Chapter 2 Installing the Cisco MDS 9100 Series Installing the Switch in a Cabinet or Rack
Tip Keep the shipping container in case the chassis requires shipping in the future.
Note If you purchased Cisco support through a Cisco reseller, contact the reseller directly. If you purchased
support directly from Cisco, contact Cisco Technical Support at this URL:
http://www.cisco.com/en/US/support/tsd_cisco_worldwide_contacts.html
Note The switch is thoroughly inspected before shipment. If any damage occurred during transportation or
any items are missing, contact your customer representative immediately.
To inspect the shipment, follow these steps:
Step 1 Compare the shipment to the equipment list provided by your customer service representative and verify
that you have received all items, including the following:
•Print documentation and CD-ROMs
•Grounding lug kit
•Rack-mount kit
•ESD wrist strap
•Cables and connectors
•Any optional items ordered
Step 2 Check for damage and report any discrepancies or damage to your customer service representative. Have
the following information ready:
•Invoice number of shipper (see packing slip)
•Model and serial number of the damaged unit
•Description of damage
•Effect of damage on the installation
Installing the Switch in a Cabinet or Rack
This section describes how to use the rack-mount kit provided with the switch to install the Cisco MDS
9100 Series into a cabinet or rack that meets the requirements described in Appendix A, “Cabinet and
Rack Installation.”
Caution If the rack is on wheels, ensure that the brakes are engaged or that the rack is otherwise stabilized.

Send documentation comments to [email protected]
2-6
Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01
Chapter 2 Installing the Cisco MDS 9100 Series
Installing the Switch in a Cabinet or Rack
The rack-mount kit provided with the switch contains the items listed in Table 2-1.
Front-Facing Installation
To install the switch in a cabinet or rack using the rack-mount kit provided with the switch, follow these
steps:
Step 1 Install the front rack-mount bracket as follows:
a. Position one of the front rack-mount brackets against the side of the switch and align the screw holes
as shown in Figure 2-1. Then attach the bracket to the switch with the three M4 screws originally
provided with the bracket.
b. Repeat with the other front rack-mount bracket on the other side of the switch.
Step 2 Install the C brackets as follows:
Note Two C brackets are shipped preinstalled on the switch, using three M3 screws per bracket. This
installation step is only necessary if the C brackets were removed.
a. Position one of the C brackets against the side of the switch and align the screw holes as shown in
Figure 2-1. Then attach the bracket to the switch with the three M3 screws originally provided with
the bracket.
b. Repeat with the other C bracket on the other side of the switch.
Table 2-1 Cisco MDS 9148, MDS 9134, and Cisco MDS 9124 Fabric Switch Rack-Mount Kit
Description Quantity
30- to 36-inch slider rails 2 per kit
24- to 30-inch slider rails 2 per kit
18- to 24-inch slider rails 2 per kit
Front rack-mount brackets 2 per kit
12-24 x 3/4-inch Phillips binder-head screws 10 per kit
10-32 x 3/4-inch Phillips binder-head screws 10 per kit
M4 x 6-mm Phillips flat-head screws 6 per kit
12-24 Cage nuts 10 per kit

Send documentation comments to [email protected]
2-7
Cisco MDS 9100 Series Hardware Installation Guide
OL-21514-01
Chapter 2 Installing the Cisco MDS 9100 Series Installing the Switch in a Cabinet or Rack
Figure 2-1 Front Rack-Mount Brackets and C Brackets Installed on the Cisco MDS 9100 Series
Step 3 Install the slider rails in the rack. Position one of the slider rails against the rack mounting rails and align
the screw holes as shown in Figure 2-2. If you are using the notched slider rails for the Cisco MDS 9134
or the Cisco MDS 9124 Switch, see Figure 2-3.
Note Depending on when you purchased your Cisco MDS 9124 Switch, you may have straight slider
rails like those shown in Figure 2-2, or you may have the notched slider rails like those shown
in Figure 2-3. Refer to the illustrations that show the type of rails that came with your switch.
Step 4 Attach the slider rail using two 12-24 screws or two 10-32 screws, depending on the rack rail thread type.
For racks with square holes, insert the 12-24 cage nuts in position behind the mounting holes in the slider
rails.
a. Repeat with the other slider rail on the other side of the rack.
1Front rack-mount bracket 2C bracket
96616
1
2

Send documentation comments to [email protected]
2-8
Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01
Chapter 2 Installing the Cisco MDS 9100 Series
Installing the Switch in a Cabinet or Rack
b. Use the tape measure and level to verify that the rails are horizontal and at the same height.
Figure 2-2 Installing the Slider Rails
Figure 2-3 Installing the Notched Slider Rails
91631
182459

Send documentation comments to [email protected]
2-9
Cisco MDS 9100 Series Hardware Installation Guide
OL-21514-01
Chapter 2 Installing the Cisco MDS 9100 Series Installing the Switch in a Cabinet or Rack
Step 5 Insert the switch into the rack:
a. By using both hands, position the switch with the back of the switch between the front
rack-mounting rails as shown in Figure 2-4. If you are using the notched rails, for the
Cisco MDS 9148 Switch, Cisco MDS 9134 Switch, or the Cisco MDS 9124 Switch, see Figure 2-5.
b. Align the two C brackets on either side of the switch with the slider rails installed in the rack. Slide
the C brackets onto the slider rails, and then gently slide the switch all the way into the rack. If the
switch does not slide easily, try realigning the C brackets on the slider rails.
Figure 2-4 Sliding the Cisco MDS 9100 Series onto the Slider Rails
91632

Send documentation comments to [email protected]
2-10
Cisco MDS 9100 Series Hardware Installation Guide OL-21514-01
Chapter 2 Installing the Cisco MDS 9100 Series
Installing the Switch in a Cabinet or Rack
Figure 2-5 Sliding the Cisco MDS 9148, Cisco MDS 9134 Switch, or the Cisco MDS 9124 Switch onto the
Notched Slider Rails
Step 6 Stabilize the switch in the rack by attaching the front rack-mount brackets to the front rack-mounting
rails:
a. Insert two screws (12-24 or 10-32, depending on rack type) and through the cage nuts and the holes
in one of the front rack-mount brackets and into the threaded holes in the rack-mounting rail (see
Figure 2-6 or Figure 2-7).
b. Repeat for the front rack-mount bracket on the other side of the switch.
If you are installing the optional cable guides, place the cable guides in front of the front rack-mount
brackets, and then pass the screws through the cable guides, front rack-mount brackets, and mounting
rail. You can install one or both cable guides; if installing a single cable guide, it can be installed on
either side.
182460