Cisco SFS 3504 Quick guide

Americas Headquarters:
© 2007 Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Cisco SFS 3504 Multifabric Server Switch
Installation and Configuration Note
This document describes how to install and configure the Cisco SFS 3504 Multifabric Server Switch.
For details about the Cisco SFS 3504 Multifabric Server Switch and switch components, see the
Cisco SFS 3504 Multifabric Server Switch Hardware Installation Guide.
Contents
This document contains the following sections:
•Safety Overview, page 2
•Parts List, page 3
•Required Tools, page 4
•Installation Guidelines, page 4
•Preparing to Install, page 5
•Installing the Cisco SFS 3504 Server Switch Components, page 5
•Installing the Cisco SFS 3504 Server Switch, page 6
•Verifying the Installation, page 11
•Configuring the Cisco SFS 3504 Server Switch, page 12
•Managing the Cisco SFS 3504 Server Switch, page 23
•Safety Warning Translation, page 23
•Related Documentation, page 29
•Obtaining Documentation, Obtaining Support, and Security Guidelines, page 29

2
Cisco SFS 3504 Multifabric Server Switch Installation and Configuration Note
78-18335-01
Safety Overview
Safety Overview
The warnings in this section, along with warnings that appear within the text of this document, apply to
the installation and configuration of the Cisco SFS 3504 Server Switch. For warning translations and
safety information, see the Regulatory Compliance and Safety Information for the Cisco Server Fabric
Switches: 7000D, 7000P, 7008P, 7012, 7024, 3012R, and 3504.
Warning Two people are required to lift the chassis. Grasp the chassis underneath the lower edge and lift with
both hands. To prevent injury, keep your back straight and lift with your legs, not your back. To prevent
damage to the chassis and components, never attempt to lift the chassis with the handles on the
power supplies or on the interface processors, or by the plastic panels on the front of the chassis.
These handles were not designed to support the weight of the chassis. Statement 5
Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly
touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94
Warning Voltage is present on the backplane when the system is operating. To reduce risk of an electric shock,
keep hands and fingers out of the power supply bays and backplane areas. Statement 166
Warning Read the installation instructions before connecting the system to the power source. Statement 1004
Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special
precautions to ensure that the system remains stable. The following guidelines are provided to ensure
your safety:
• This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
• When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest
component at the bottom of the rack.
•If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in
the rack. Statement 1006
Warning IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device.
Statement 1071
SAVE THESE INSTRUCTIONS

3
Cisco SFS 3504 Multifabric Server Switch Installation and Configuration Note
78-18335-01
Parts List
Warning This unit is intended for installation in restricted access areas. A restricted access area can be
accessed only through the use of a special tool, lock and key, or other means of security.
Statement 1017
Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Warning This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260.
Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The
telecommunications lines must be disconnected 1) before unplugging the main power connector or 2)
while the housing is open, or both. Statement 1043
Warning This product requires short-circuit (overcurrent) protection, to be provided as part of the building
installation. Install only in accordance with national and local wiring regulations. Statement 1045
Warning Use of controls, adjustments, or performing procedures other than those specified may result in
hazardous radiation exposure. Statement 1057
Parts List
The Cisco SFS 3504 Server Switch kit contains the following parts:
•One 5-slot multifabric server switch chassis
•One InfiniBand switch card
•One to four gateway modules, depending upon your configuration:
– Ethernet gateway Product ID: SFS-3500-ENGW-1G
– Fibre Channel gateway Product ID: SFS-3500-FCGW-4G
•Zero to three gateway blanking panels for I/O slots, depending upon your configuration
•One or two power supplies, depending upon your configuration
•Zero or one power supply blanking panel, depending upon your configuration

4
Cisco SFS 3504 Multifabric Server Switch Installation and Configuration Note
78-18335-01
Required Tools
•An accessory kit containing the following:
– One or two power cords, depending upon your configuration
– One console cable connector kit
– Two fixed rack ear brackets
– Two adjustable rack ear brackets
– One disposable ESD grounding wrist strap
– One rack-mount hardware kit with six M4x 8 mm flat-head Phillips screws
– One copy of this Cisco SFS 3504 Multifabric Server Switch Installation and Configuration Note
document
– One copy of the Regulatory Compliance and Safety Information for the Cisco Server Fabric
Switches: 7000D, 7000P, 7008P, 7012, 7024, 3012R, and 3504 document
– One standard warranty package
Required Tools
The following tools are required to install the Cisco SFS 3504 Server Switch:
•Number 1 Phillips screwdriver
•Number 2 Phillips screwdriver
•Eight screws, standard for your rack
•Eight rack nuts, standard for your rack
•Antistatic mat or foam pad to support the switch module and the gateways
•Your own ESD-prevention equipment or the included disposable ESD grounding wrist strap
Installation Guidelines
Use the following guidelines when installing a Cisco SFS 3504 Server Switch:
•Make two people available for lifting the chassis onto the rack.
•Verify that the rack environment provides sufficient ventilation:
– Maintain ambient airflow throughout the site to ensure normal operation.
– If installing in an enclosed cabinet, ensure that the cabinet has adequate ventilation, and allow
at least 2.5 inches (6.4 cm) of clearance between the chassis vents and cabinet doors.
– If placing the switch adjacent to a device that exhausts air toward the switch, the horizontal
distance between the devices should be a minimum of 6 inches (15.2 cm).
– Ensure that cables do not obstruct the airflow through the chassis.
•Ground yourselves using approved ESD grounding wrist straps.
•Read the “Safety Overview” section on page 2, and observe the following cautions:
Caution Do not lift the Cisco SFS 3504 Server Switch chassis by the front (power-fan module end) and back
(cable end). Lift the unit by the sides to prevent damage.

5
Cisco SFS 3504 Multifabric Server Switch Installation and Configuration Note
78-18335-01
Preparing to Install
Preparing to Install
To prepare for your installation, unpack the product, ensure that all necessary components are available,
and perform the following steps:
Step 1 Remove all components from the Cisco SFS 3504 Server Switch shipping container, and identify them
according to the “Parts List” section on page 3.
Warning Two people are required to lift the chassis. Grasp the chassis underneath the lower edge and lift with
both hands. To prevent injury, keep your back straight and lift with your legs, not your back. To prevent
damage to the chassis and components, never attempt to lift the chassis with the handles on the
power supplies or on the interface processors, or by the plastic panels on the front of the chassis.
These handles were not designed to support the weight of the chassis. Statement 5
Step 2 Place the chassis on a secure, clean surface.
Step 3 Verify that you have the parts for the rail kit to mount the switch on the rack (parts shipped with the
Cisco SFS 3504 Server Switch in the accessory kit), or verify that you have the parts for the optional
Cisco Server Fabric Switches Rack Shelf Kit (ordered and shipped separately, product number
SFS-7008P-RKIT=).
Step 4 Verify that you have available all Ethernet gateways, Fibre Channel gateways, and blanking panels to
install in your system, as appropriate for your configuration.
Caution Prepare a management workstation (not included), such as a PC running terminal-emulation software
(not included), a straight-through M/F DB-9 serial cable (included), and a DB-9 to RJ45 adaptor
(included).
Installing the Cisco SFS 3504 Server Switch Components
According to your specific order, Cisco SFS 3504 Server Switch components are pre-installed in your
Cisco SFS 3504 Server Switch chassis before shipping, including the InfiniBand switch card, Ethernet
and Fibre Channel gateway modules, and power-fan modules. You can, if required for your
configuration, add or replace these components before mounting the Cisco SFS 3504 Server Switch
chassis or add additional components at a later date.
Note Whenever possible, we recommend that you install any additional components before you mount the
Cisco SFS 3504 Server Switch in the rack or on the optional shelf.

6
Cisco SFS 3504 Multifabric Server Switch Installation and Configuration Note
78-18335-01
Installing the Cisco SFS 3504 Server Switch
Installing the Cisco SFS 3504 Server Switch
You can install the switch in the rack with the power-fan modules flush to the front of the rack or with
the data connection cables mounted flush to the front.
This section contains the following topics:
•Installing with the Power-fan Modules Flush-front, page 6
•Installing with the Data Connection Cables Flush-front, page 8
Note Install the Cisco SFS 3504 Server Switch on a rack using the rail kit that is included with the chassis or
on the optional shelf that is ordered and shipped separately (product number SFS-7008P-RKIT=).
Installing with the Power-fan Modules Flush-front
To install the Cisco SFS 3504 Server Switch on a rack so that the power-fan module end is flush mounted
to the front rack posts, perform the following steps:
Step 1 Open the bag that contains the mounting hardware.
Note To mount a Cisco SFS 3504 Server Switch on a rack, use eight screws and eight rack nuts. These
screws and nuts must be supplied by the customer, based upon compatibility with the rack.
Step 2 Attach the two rack ear brackets to the power-fan module end of the chassis using a Phillips screwdriver and
the six M4 x 8 mm flat-head screws provided (three on each side), as shown in Figure 1. Firmly tighten the
screws on the rack ear brackets to secure them to the chassis.
Figure 1 Attaching the Rack Ear Brackets at the Power-Fan Module End
1Rack ear brackets 2Guide rails (pre-attached)
250376
INPUT
OK
FAN
OK
OUTPUT
FAIL
SFS3500
Series
CAUTION: DISCONNECTPOWERBEFORESERVICING
!
ALLFASTENERSMUSTBE
FULL
YENGAGEDPRIOR
TO
OPERATIONOFPOWERSUPPL
Y
100-240V
8-4A
50/60Hz
INPUT
OK
FAN
OK
OUTPUT
FAIL
SFS3500
Series
CAUTION: DISCONNECTPOWERBEFORE SERVICING
!
ALLFASTENERSMUSTBE
FULL
YENGAGEDPRIORTO
OPERATIONOFPOWERSUPPL
Y
100-240V
8-4A
50/60Hz
1
1
2

7
Cisco SFS 3504 Multifabric Server Switch Installation and Configuration Note
78-18335-01
Installing the Cisco SFS 3504 Server Switch
Step 3 Slide the Cisco SFS 3504 Server Switch between the rack posts (see Figure 2), until the rack ear brackets
on the front of the chassis make contact with the front rack posts.
Use four customer-supplied fasteners (two for each side) and the appropriate screwdriver (not included
in the accessory kit) to firmly secure the rack ear brackets to the front rack posts.
Note The handle on the AC power-fan module and/or the blanking panel can be used as an aid to
support the power-fan module side of the chassis during rack-mounting installation.
Figure 2 Sliding the Cisco SFS 3504 Server Switch Between Rack Posts and Inserting Brackets
Step 4 Slide the two adjustable brackets, from the back, between each of the guide rails that are attached on
either side of the Cisco SFS 3504 Server Switch at the data connection end. (See Figure 2.)
Step 5 Adjust the adjustable brackets so that the holes in the brackets align with the holes in the rack posts, and
secure the brackets to the rack posts. (See Figure 2.)
Use four standard rack screws (two for each bracket; rack screws not included in the accessory kit) to
secure the adjustable brackets to the rear rack posts.
241649
INPUT
OK
FAN
OK
OUTPUT
FAIL
SFS3500
Series
CAUTION: DISCONNECT POWER BEFORE SERVICING
!
ALL FASTENERS MUST BE
FULLYENGAGED PRIOR
TO
OPERATION OF POWERSUPPLY
100-240V
8-4A
50/60Hz
INPUT
OK
FAN
OK
OUTPUT
FAIL
SFS3500
Series
CAUTION: DISCONNECT POWER BEFORE SERVICING
!
ALL FASTENERS MUST BE
FULL
Y ENGAGED PRIOR TO
OPERATION OF POWERSUPPLY
100-240V
8-4A
50/60Hz

8
Cisco SFS 3504 Multifabric Server Switch Installation and Configuration Note
78-18335-01
Installing the Cisco SFS 3504 Server Switch
Note The least amount of protrusion for the adjustable brackets must be 1/2 inch beyond the inside end of the
guide rail. The adjustable bracket should always be fully supported by the guide rails.
Installing with the Data Connection Cables Flush-front
To install the Cisco SFS 3504 Server Switch on a rack so that the data connection cables are flush-front
on the rack posts, perform the following steps:
Step 1 Open the bag that contains the mounting hardware.
Note To mount a Cisco SFS 3504 Server Switch on a rack, use eight screws and eight rack nuts. These
must be supplied by the customer, based upon the compatibility of the screws and nuts with the
specific racks.
Step 2 Remove the two guide rails that are attached to either side of the Cisco SFS 3504 Server Switch at the
data-connection end, and attach the guide rails similarly at the power-fan modules end. (See Figure 3.)
Use a Phillips screwdriver to unscrew the guide rails, and secure them at the new locations with the
screws that you just removed.
Figure 3 Attaching Guide Rails at the Power-Fan Module End
1Guide rails
250430
Cisco SFS3504 Multifabric Switch
!
OK
123456789101112
TX/RX
Link
D
SFS3500 Series FC Gateway
!
OK
1234
Fault
Link
SFS3500SeriesEthernet Gateway
!
OK
123456
TX/RXLink
100/1000Base
T
1
1
1

9
Cisco SFS 3504 Multifabric Server Switch Installation and Configuration Note
78-18335-01
Installing the Cisco SFS 3504 Server Switch
Step 3 Attach the two rack ear brackets to the data-connection end of the chassis using a Phillips screwdriver
and the six M4 x 8 mm screws provided (three for each bracket), as shown in Figure 4. Use the three
holes of the rack ear brackets. Firmly tighten the screws on the rack ear brackets to secure them to the
chassis.
Figure 4 Attaching the Rack Ear Brackets to the Data Connection End
Step 4 Slide the Cisco SFS 3504 Server Switch between the rack posts (see Figure 5) until the rack ear brackets
on the chassis make contact with the front rack posts. Use four customer-supplied fasteners (two for each
side) and the appropriate screwdriver (not included in the accessory kit) to firmly secure the rack ear
brackets to the front rack posts.
1Rack ear brackets
1
250431
Cisco SFS3504 Multifabric Switch
!
OK
123456789101112
TX/RX
Link
D
SFS3500 Series FC Gateway
!
OK
1234
Fault
Link
SFS3500SeriesEthernet Gateway
!
OK
123456
TX/RXLink
100/1000Base
T
1

10
Cisco SFS 3504 Multifabric Server Switch Installation and Configuration Note
78-18335-01
Installing the Cisco SFS 3504 Server Switch
Figure 5 Sliding the Cisco SFS 3504 Server Switch Between Rack Posts and Inserting Brackets
Step 5 Slide the two adjustable brackets, from the back, between each of the guide rails that are attached on
either side of the Cisco SFS 3504 Server Switch at the power-fan modules end. (See Figure 5.)
Step 6 Adjust the adjustable brackets so that the holes in the brackets align with the holes in the rack posts, and
secure the adjustable brackets to the rack posts. (See Figure 5.)
Use four standard rack screws (two for each bracket; rack screws not included in the accessory kit) to
secure the adjustable brackets to the rear rack posts.
241650
Cisco SFS3504 Multifabric Switch
!
OK
123456789101112
TX/RX
Link
D
SFS3500 Series FC Gateway
!
OK
1234
Fault
Link
SFS3500SeriesEthernetGateway
!
OK
123456
TX/RXLink
100/1000BaseT