Clam Corp Fish Trap Voyager Special 8208 User manual

Model No.
-8208-
Specifications
▪Height - 72 inches
▪Length - 93 inches
▪W i d t h - 72 inches
▪Weight - 120 lbs.
p/n 108208
Instruction No. 101930
- Clam Customer Service Information -
NOTICE!! - ONCE USED, THIS SHELTER CANNOT BE RETURNED TO THE STORE. IF YOU HAVE
A WARRANTY CLAIM, PLEASE CONTACT CLAM CORP. CUSTOMER SERVICE BY EMAIL
INQUIREY OR DIRECT BY CALLING:
■Customer Service Hrs: - 9am to 4pm, Mon. - Fri. Central Standard Time
■Clam Corporation, Inc.
600 Clydesdale Trail
Medina, MN 55340
■Phone - 763-231-4120
■Fax - 763-231-4121
■Email – [email protected]
■Website – www.clamcorp.com

2
- Bill of Materials -

3
- Assembly Diagram -

4
- Step One -

5
- Step Two -

6
- Step Three -

7
- Step Four -

8
- Step Five -
Note: Actual Canopy Bracket configuration may vary
If your Canopy Brackets have four holes near the upper angled edge rather than three
hole configuration shown, use the A,B, & D locations stamped on the four hole bracket.
Seating has be omitted for clarity

9
- Step Six -
Slide the Canopy Hoop Poles onto the Canopy Poles until the spring buttons engage the holes near the
ends of each Canopy Hoop Pole.
Support the first Canopy Hoop Pole as pictured with the Rear Adjustable Spreader Poles (the shorter of
the two provided lengths).
Lean the two remaining Canopy Hoop Poles against the first.
Note: Seating has be omitted for clarity

10
- Step Seven -
Drape the Tent over the supported hoops then go inside and spread out the Canopy Hoop Poles,
attaching the Roof Velcro as you go.
Orient the Porch Hoop Pole so that the holes face upward and then feed the length of the pole through
the three Porch Hoop Sleeves sewn on the Tent. Slide the Porch Hoop Pole onto the Porch Poles,
engaging the third hole position.
Attach the Porch Hoop Velcro on each side of the Tent. Remove the Rear Adjustable Spreader Poles
now supporting the hoops to allow the tent to be “set” in the next step.
Note: Seating has be omitted for clarity

11
- Step Eight -
To “set” the tent, grasp the tent material at the rear of the shelter and pull it downward. Observe the
porch area of the tent lifting accordingly as you pull. When the U-Channel Molding is correctly
installed, the Porch Hoop Pole will lightly touch the floor.
To achieve this condition, start by finding the center of the Molding. From behind the unit, pull the
midpoint of the Tent downward and fold the Tent material under the lip of the Base. Then press the
midpoint of the molding over the Tent material and Base lip. Continue pressing outward in both
directions until you have secured about twelve inches of material to the base
Having temporarily secured the tent to the base, take a walk around the unit. Readjust the Molding
until you have verified the proper Porch Hoop Pole position and also that the Tent sides and corners
are properly proportioned.
When satisfied, continue applying the Molding around the shelter, one direction from center and then
the other, pulling the material as you go so that surface is relatively wrinkle-free and snug. You may
need to trim the Molding ends if they are not equal.
Install the Front, Rear, and Roof Spreader Poles as indicated. Adjust the Front and Rear Spreader
Poles to tighten the fit of the tent.
If everything still looks good, secure the Molding with the included #6 Phillips Screws. Evenly space
them about every ten to twelve inches, and also put a screw in the center of both corners. Since there
aren’t any predrilled holes, it's advisable to use a powered driver for this operation.

12
- License Holder -
If Licensing is required in your area, locate a
position on the outside of your tent that you wish
to affix the License Holder.
Next hold the License Holder in the determined
position and use a sharp object to pierce two
holes in the tent; going through the grommets of
the License Holder.
Place the included Snap Buttons through the
pierced holes and through the License Holder
grommets. Push the Buttons together firmly to
secure the holder in place.
- Safety Instructions -
Please fully understand and follow all safety instructions as outlined. Failure to do so could result in
severe injury or death.
▪
Do not use open flame heaters in your ice shelter. Injury or death may result from fire if tent fabric is
exposed to open flame. The tent is not fireproof, but the fabric is treated with a fire retardant that
meets CPAI-84 specifications. Application of any foreign substance may render the flame retardant
properties ineffective. Ice Armor fabric will melt when contact is made with hot surfaces (i.e.,
heaters).
▪
Death from asphyxiation may result from use of oxygen depleting heaters. Open all vents for fresh air
ventilation.
▪
Never leave shelter unattended when set up.
▪
Due to the increase in traffic (snowmobiles, autos, etc.) on area lakes, ice fishing can be hazardous at
night. If you choose to fish at night or in poor visibility conditions, be sure to take precautions with
lights or reflectors to show drivers your whereabouts. Night time: exterior reflectors must be visible
to reduce risk of collisions.
- Warranty -
Clam Corporation, Inc. warrants to the original retail purchaser that all Clams are free from
manufacturer’s defects for one (1) year from the date of the original purchase. Warranty does not
cover cracked windows, tent tears, broken or bent hoops due to high wind weather conditions or
unattended use. Clam Corporation will replace or repair any part found defective within the one (1)
year time limit. All parts must be returned to Clam Corporation, Inc. Before returning any parts, you
must first call or write and acquire a return authorization. All returns must be returned postage-
prepaid and include the original cash register receipt (date and purchase price).
- Limitation of Liability -
It is expressly understood that Clam Corporation liability for its products, whether due to breach of
warranty, negligence, strict liability, or otherwise, is limited to the repair of the product as stated
above. Clam Corporation is not liable for any injury, loss, damage, or expense, whether direct or
consequential, including but not limited to loss of use, income, profit, or damage to material arising in
connection with the sale, installation, use of, inability to use, or the repair or replacement of Clam
Corporation products. Clam Corporation reserves the right to make alterations or modifications in its
products at any time, which in its opinion, may improve the performance and efficiency of the product.
It shall not be obligated to make such alterations or modifications to products already in service.