Clam Corp Fish Trap X 8236 User manual

model No.
-8236-
Specifications
ŀHeight - 68 inches
ŀLength - 79 inches
ŀW i d t h - 62 inches
ŀWeight - 120 lbs.
p/n 108236
Instruction No. 101914
- Clam Customer Service Information -
NOTICE!! - ONCE USED, THIS SHELTER CANNOT BE RETURNED TO THE STORE. IF YOU HAVE
A WARRANTY CLAIM, PLEASE CONTACT CLAM CORP. CUSTOMER SERVICE BY EMAIL
INQUIREY OR DIRECT BY CALLING:
ɵCustomer Service Hrs: - 9am to 4pm, Mon. - Fri. Central Standard Time
ɵClam Corporation, Inc.
600 Clydesdale Trail
Medina, MN 55340
ɵPhone - 763-231-4120
ɵFax - 763-231-4121
ɵEmail – [email protected]
ɵWebsite – www.clamcorp.com

2
- Bill of Materials -
ITEM
Q
TY P
/
N DESCRIPTION ITEM
Q
TY P
/
NDESCRIPTION
1 4 101048 BLOCK
,
SLIDE 17 1 101811 BASE
,
MEDIUM XTR
2 18 101081 WASHER
,
1
/
4" FLAT 18 2 101813 BRKT
,
RAIL HANGER
3 26 101082 LOCKNUT
,
1
/
4" THIN 19 1 101817 BRKT
,
FRONT SEAT
4 8 101088 SCREW
,
1
/
4-20 X 0.75 PHILLIPS 20 6 101829 POLE ASSY
,
STRAIGHT POLE
5 2 101146 ANGLE
,
9" LONG ALUMINUM ANGLE 21 2 101830 POLE ASSY
,
BENT CANOPY
6 4 101147 SCREW
,
#10 X 1" LONG PHILLIPS 22 2 101836 POLE ASSY
,
FRONT SPREADER
7 1 101399 PLATE
,
6" S
Q
UARE SWIVEL 23 1 101840 POLE ASSY
,
REAR SPREADER
8 1 101424 BRKT
,
REAR SEAT 24 1 101842 TENT
,
X
9 4 101429 CAP
,
1-1
/
8" TUBE 25 4 101862 POLE ASSY
,
CANOPY HOOP
10 1 101442 CLIP
,
LATCH 26 2 101864 POLE ASSY
,
ROOF SPREADER
11 1 101466 HAMMOCK
,
CLOTH ACCESSORY 27 1 101905 SEAT ASSY
,
TWO-TONE
12 8 101470 BOLT
,
1
/
4" DIA HEX HEAD BOLT X 1
/
2" 28 8 101906 SCREW
,
1
/
4" DIA X 2-1
/
2" PHILLIPS
13 2 101473 SCREW
,
1
/
4" DIA X 1-1
/
2" PHILLIPS 29 1 101907 TUBE
,
MED XTR SEAT RAIL
14 4 101486 SCREW
,
1
/
4" DIA X 1-3
/
4" PHILLIPS 30 1 101909 MOLDING
,
U-CHANNEL
15 2 101652 TUBE
,
1-1
/
8" DIA 31 20 101938 SCREW
,
#8 PHILLIPS
16 2 101810 BRKT
,
XTR CANOPY
- Seat Parts Diagram (See pg. 4 for Assembly) -

3
- Shelter Parts Diagram (See pg. 4 for Assembly) -

4
- Step 0ne -

5
- Step Two -

6
- Step Three -

7
- Step Four -

8
- Step Five -

9
- Step Six -

10
- Step Seven -

11
- Step Eight -

12
- Step Nine -

13
- Step Ten -

14
- Seating Installation -
Angle the Seat Assembly slightly while placing the bottom lip of the Front Seat Bracket under the
outside edge of the Base Lip.
With the Latch Clip hanging freely, tilt the complete assembly downward until the interior of the Rear
Seat Bracket surrounds the Support Tube.

15
- Seating Installation (cont.) -
Reach under the Rear Seat Bracket and slide the Latch Clip outwards and then up against the underside
of the Support Tube. Squeeze the Latch Clip into the horizontal slot of the Rear Seat Bracket.
Secure the position of the Latch Clip by pushing it into the two holes located above the horizontal slot
of the Rear Seat Bracket.
WARNING: ALWAYS KEEP THE LATCH CLIP IN THE SECURED POSITION DURING USE.
FAILURE TO DO SO COULD RESULT IN INJURY FROM THE SEAT COMING OFF OF ITS
MOUNTING SYSTEM.
Included is a Tow Rope for those not planning to install the optional Tow Hitch Assembly (available for
purchase at www.clamcorp.com.). Two install the Tow Rope, drill two 1/2" holes in the sloped front of
the Base. Knot the ends of the Tow Rope after routing through the drilled holes.

16
- Safety Instructions -
Please fully understand and follow all safety instructions as outlined. Failure to do so could result in
severe injury or death.
ŀDo not use open flame heaters in your ice shelter. Injury or death may result from fire if tent fabric is
exposed to open flame. The tent is not fireproof, but the fabric is treated with a fire retardant that
meets CPAI-84 specifications. Application of any foreign substance may render the flame retardant
properties ineffective. Ice Armor fabric will melt when contact is made with hot surfaces (i.e.,
heaters).
ŀDeath from asphyxiation may result from use of oxygen depleting heaters. Open all vents for fresh air
ventilation.
ŀNever leave shelter unattended when set up.
ŀDue to the increase in traffic (snowmobiles, autos, etc.) on area lakes, ice fishing can be hazardous at
night. If you choose to fish at night or in poor visibility conditions, be sure to take precautions with
lights or reflectors to show drivers your whereabouts. Night time: exterior reflectors must be visible
to reduce risk of collisions.
- Warranty -
Clam Corporation, Inc. warrants to the original retail purchaser that all Clams are free from
manufacturers defects for one (1) year from the date of the original purchase. Warranty does not cover
cracked windows, tent tears, broken or bent hoops due to high wind weather conditions or unattended
use. Clam Corporation will replace or repair any part found defective within the one (1) year time limit.
All parts must be returned to Clam Corporation, Inc. Before returning any parts, you must first call or
write and acquire a return authorization. All returns must be returned postage-prepaid and include the
original cash register receipt (date and purchase price).
- Limitation of Liability -
It is expressly understood that Clam Corporation liability for its products, whether due to breach of
warranty, negligence, strict liability, or otherwise, is limited to the repair of the product as stated
above. Clam Corporation is not liable for any injury, loss, damage, or expense, whether direct or
consequential, including but not limited to loss of use, income, profit, or damage to material arising in
connection with the sale, installation, use of, inability to use, or the repair or replacement of Clam
Corporation products. Clam Corporation reserves the right to make alterations or modifications in its
products at any time, which in its opinion, may improve the performance and efficiency of the product.
It shall not be obligated to make such alterations or modifications to products already in service.