Clam Corp Fish Trap X4 8235 User manual

Model No.
- 8 2 3 5 -
(p/n 108327)
Specifications
▪
Height – 75”(24”packed)
▪
Width - 75 inches
▪
Length – 144”(45”packed)
▪
Weight - 175 lbs
▪
Instruction p/n 102484
- Clam Customer Service Information -
NOTICE!! Once used, this shelter cannot be returned to the store. If you have a
warranty claim, have your sales receipt ready and contact Clam Corporation
Customer Service by email inquiry or direct by calling:
▪
Customer Service Hrs: - 9am to 4pm, Mon. - Fri. Central Standard Time
▪
Clam Corporation
600 Clydesdale Trail
Medina, MN 55340
▪
Phone - 763-231-4120
▪
Fax - 763-231-4121
▪
Website – www.clamcorp.com
▪
Email – [e-mail]
Clam Corporation cannot honor warranty without an original, dated receipt.

2
- Parts List –
Item Qty p/n Description
1 16 101048 Slide Block
2 36 101081 1/4" Flat Washer
3 46 101082 1/4" Thin Locknut
4 10 101088 1/4" Dia. X 3/4" Long Phillips Screw
5 8 101146 1-1/2" X 1-3/4" Aluminum Angle X 9" Long
6 16 101147 #10 X 1" Long Phillips Screw
7 1 101249 Tow Rope
8 4 101399 Seat Swivel Assembly
9 8 101429 1-1/8" Dia. Tube Cap
10 32 101470 1/4" Dia. X 1/2" Long Hex Head Screw
11 8 101486 1/4" Dia. X 1-3/4" Long Phillips Screw
12 2 101618 Base Attachment Strap
13 4 101803 1-1/8”Dia. Tube
14 2 101809 Front Seat Bracket
15 2 101817 Rear Seat Bracket
16 8 101829 Straight Canopy Pole
17 4 101830 Bent Canopy Pole
18 4 101836 Front Adjustable Spreader Pole
19 3 101839 Roof Spreader Pole
20 6 101863 Canopy Hoop Pole
21 2 101900 RH Canopy Bracket
22 2 101901 LH Canopy Bracket
23 4 101905 Folding Seat Assembly
24 12 101906 1/4" Dia. X 2-1/2" Long Phillips Screw
25 1 102185 X4 Base
26 1 102438 X4 Tent
27 1 102484 Manual, 08/09 X4

3
- Parts Diagram (Seating) -

4
- Parts Diagram (Shelter) -

5
- Step 0ne -

6
- Step Two -

7
- Step Three -

8
- Step Four -

9
- Step Five -

10
- Step Six -

11
- Step Seven -

12
- Step Eight -
X4 Tent
(p/n 102438)

13
- Step Nine -

14
- Seating Installation -
Angle the seat assembly slightly while placing the bottom lip of the front seat bracket under the outside
edge of the base lip.
Carefully rotate the complete seat assembly down onto the opposite base ledge, capturing the ledge with
the rear seat bracket.

15
- Rope Installation -
Included is a tow rope for those not planning to install the optional tow hitch assembly (available for
purchase at www.clamcorp.com.). Two install the tow rope, drill two 1/2" holes about midway in the
sloped front of the base. Knot the ends of the tow rope after routing through the drilled holes.
- Safety Instructions -
Please fully understand and follow all safety instructions as outlined. Failure to do so could result in
severe injury or death.
▪
Do not use open flame heaters in your ice shelter. Injury or death may result from fire if tent fabric is
exposed to open flame. The tent is not fireproof, but the fabric is treated with a fire retardant that meets
CPAI-84 specifications. Application of any foreign substance may render the flame retardant properties
ineffective. Ice Armor fabric will melt when contact is made with hot surfaces (i.e., heaters).
▪
Death from asphyxiation may result from use of oxygen depleting heaters. Open all vents for fresh air
ventilation.
▪
Never leave shelter unattended when set up.
▪
Due to the increase in traffic (snowmobiles, autos, etc.) on area lakes, ice fishing can be hazardous at
night. If you choose to fish at night or in poor visibility conditions, be sure to take precautions with
lights or reflectors to show drivers your whereabouts. Night time: exterior reflectors must be visible to
reduce risk of collisions.
- Warranty -
Clam Corporation warrants to the original retail purchaser that all Clams are free from manufacturer’s
defects for one (1) year from the date of the original purchase. Warranty does not cover cracked
windows, tent tears, broken or bent hoops due to high wind weather conditions or unattended use. Clam
Corporation will replace or repair any part found defective within the one (1) year time limit. All parts
must be returned to Clam Corporation. Before returning any parts, you must first call or write and acquire
a return authorization number. All returns must be returned postage-prepaid and include the original cash
register receipt (date and purchase price).
Note: Please write the return authorization number on the outside of the package to help
ensure the transaction gets processed swiftly and accurately.
- Limitation of Liability -
It is expressly understood that Clam Corporation’s liability for its products, whether due to breach of
warranty, negligence, strict liability, or otherwise, is limited to the repair of the product as stated above.
Clam Corporation is not liable for any injury, loss, damage, or expense, whether direct or consequential,
including but not limited to loss of use, income, profit, or damage to material arising in connection with
the sale, installation, use of, inability to use, or the repair or replacement of Clam Corporation products.
Clam Corporation reserves the right to make alterations or modifications in its products at any time, which
in its opinion, may improve the performance and efficiency of the product. It shall not be obligated to
make such alterations or modifications to products already in service.