Clam Corp Fish Trap Scout 8244 User manual

Model No.
- 8244 -
p/n 108321
Specifications
▪
Height: 58”(20”packed)
▪
Width: 36”
▪
Depth: 80”(48”packed)
▪
Weight: 47 lbs.
▪
Instruction p/n 102475
- Clam Customer Service Information -
NOTICE!! Once used, this shelter cannot be returned to the store. If you have a
warranty claim, have your sales receipt ready and contact Clam Corporation
Customer Service by email inquiry or direct by calling:
▪
Customer Service Hrs: - 9am to 4pm, Mon. - Fri. Central Standard Time
▪
Clam Corporation
600 Clydesdale Trail
Medina, MN 55340
▪
Phone - 763-231-4120
▪
Fax - 763-231-4121
▪
Website – www.clamcorp.com
▪
Email – [e-mail]
Clam Corporation cannot honor warranty without an original, dated receipt.

2
- Parts List -
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 101080 SCREW, 1/4-20 X 1.25 8
2 101081 WASHER, 1/4 FLAT 16
3 101082 NUT, 1/4-20 THIN NYLOCK 26
4 101083 TUBE SPACER CAP 8
5 101088 SCREW, 1/4-20 X 0.75 14
6 101140 SCOUT PORCH HOOP 1
7 101043 LH CANOPY BRACKET 1
8 101609 SEAT RAIL SUPPORT BRACKET 2
9 101042 RH CANOPY BRACKET 1
10 101141 SCOUT CANOPY HOOP 3
11 102494 BASE, SCOUT 08-09 1
12 101095 TOW ROPE, 3/8 DIA X 9 FT 1
13 101096 U-CHANNEL MOLDING, SCOUT 1
14 101148 SCREW, #6 X 0.38 16
15 101055 STADIUM SEAT 1
16 101486 SCREW, 1/4-20 X 1.75 4
17 101144 ACCESSORY HAMMOCK, SCOUT 1
18 101429 PLUG, 1.16 DIA TUBE 4
19 101097 SCREW, #14 X 1.00 4
20 101607 SCOUT SEAT RAIL TUBE 2
21 101147 SCREW, #10 x 1.00 4
22 101048 SLIDE BLOCK 4
23 101146 ALUMINUM CHANNEL 2
24 102432 TENT, 08/09 SCOUT 1
25 102475 MANUAL, 08/09 SCOUT 1

3
- Parts Diagram -

4
- Step One -

5
- Step Two -

6
- Step Three -
Scout Base
(p/n 102494)

7
- Step Four -

8
- Step Five -

9
- Step Six -

10
- Step Seven -

11
- Step Eight -
Scout Tent
(p/n 102432)

12
- Step Nine -

13
- Step Ten -
If everything still looks good, secure the Molding wit
h the #6 Phillips Screws. Evenly space
them about every ten to twelve inches, and also put a screw in the center of both corners.
Since there aren’t any predrilled holes, it's advisable to use a powered driver for this operation.

14
- Set-up & Take Down -
Set-Up - Rotate the hoop poles forward, then position and expand the adjustable spreader pole in the
rear of the unit to take the slack out of the tent. Tighten the tension knob on the rear adjustable
spreader pole to hold its position.
Take-Down - Go around the shelter and tuck the tent material in between the rested hoops to keep the
tent from spilling out of the base and contacting the ground. Also make sure that the tent is clear of the
canopy brackets edges and other items in the base which might cause rubbing and premature wear to
the tent. If you purchased the optional travel cover, cover your shelter to protect your gear from the
elements during transport.
- Safety Instructions -
PLEASE FULLY UNDERSTAND AND FOLLOW ALL SAFETY INSTRUCTIONS AS OUTLINED.
FAILURE TO DO SO COULD RESULT IN SEVERE INJURY OR DEATH.
▪
Do not use open flame heaters in your ice shelter. Injury or death may result fromfire if tent fabric is
exposed to open flame. The tent is not fireproof, but the fabric is treated with a fire retardant that
meets CPAI-84 specifications. Application of any foreign substance may render the flame retardant
properties ineffective. Ice Armor fabric will melt when contact is made with hot surfaces (i.e.,
heaters).
▪
Death from asphyxiation may result from use of oxygen depleting heaters. Open all vents for fresh
air ventilation.
▪
Never leave shelter unattended when set up.
▪
Due to the increase in traffic (snowmobiles, autos, etc.) on area lakes, ice fishing can be hazardous
at night. If you choose to fish at night or in poor visibility conditions, besure to take precautions with
lights or reflectors to show drivers your whereabouts. Exterior reflectors must be visible at all times
to reduce risk of collisions.
- Warranty -
Clam Corporation warrants to the original retail purchaser that all Clams are free from manufacturer’s
defects for one (1) year from the date of original purchase. Warranty does not cover cracked windows,
tent tears, broken or bent hoops due to high wind weather conditions or unattended use. Clam
Corporation will replace or repair any part found defective within the one (1) year time limit. All parts
must be returned to Clam Corporation. Before returning any parts, you must first call or write and
acquire a return authorization. All returns must be returned postage-prepaid and include the original
cash register receipt (date and purchase price).
Note: Please write the return authorization number on the outside of the package to help
ensure the transaction gets processed swiftly and accurately.
- Limitation of Liability -
It is expressly understood that Clam Corporation’s liability for its products, whether due to breach of
warranty, negligence, strict liability, or otherwise, is limited to the repair of the product as stated above.
Clam Corporation is not liable for any injury, loss, damage, or expense, whether direct or consequential,
including but not limited to loss of use, income, profit, or damage to material arising in connection with
the sale, installation, use of, inability to use, or the repair or replacement of Clam Corporation products.
Clam Corporation reserves the right to make alterations or modifications in its products at any time,
which in its opinion, may improve the performance and efficiency of the product. It shall not be obligated
to make such alterations or modifications to products already in service.