Clare Controls CM-BT10-TXRX100 User manual

Doc ID 2015-04-620 • Rev 03
HDBaseT Extender Set 100m
User Guide
Model CM-BT10-TXRX100

Copyright
© 24APR15 Clare Controls, Inc. All rights reserved.
This document may not be copied in whole or in part or otherwise
reproduced without prior written consent from Clare Controls, Inc.,
except where specifically permitted under US and international
copyright law.
Trademarks and
patents
HDBaseT Extender Set 100m, Model CM-BT10-TXRX100 name is
a trademark of Clare Controls, Inc.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer
Clare Controls, Inc.
7519 Pennsylvania Ave., Suite 104, Sarasota, FL 34243, USA
Version
This document applies to HDBaseT Extender Set 70m User Guide,
Model CM-BT10-TXRX100.
Contact information
For contact information, see www.clarecontrols.com.

HDBaseT Extender Set 100m User Guide i
Content
Limitation of liability...ii!
Introduction...1!
Features...1!
Packagecontents...1!
Product appearance...2!
Twisted pair cable connection...4!
System connection...5!
Usage precautions...5!
Application examples...5!
Connection procedure...6!
Application...7!
Specifications...8!
Dimensions...9!
Troubleshooting and maintenance...11!
Safety operation...12!
After-sales service...13!

ii HDBaseT Extender Set 100m User Guide
Limitation of liability
To the maximum extent permitted by applicable law, in no event will Clare
Controls, Inc. be liable for any lost profits or business opportunities, loss of
use, business interruption, loss of data, or any other indirect, special,
incidental, or consequential damages under any theory of liability, whether
based in contract, tort, negligence, product liability, or otherwise. Because
some jurisdictions do not allow the exclusion or limitation of liability for
consequential or incidental damages the preceding limitation may not apply to
you. In any event the total liability of Clare Controls, Inc. shall not exceed the
purchase price of the product. The foregoing limitation will apply to the
maximum extent permitted by applicable law, regardless of whether Clare
Controls, Inc. has been advised of the possibility of such damages and
regardless of whether any remedy fails of its essential purpose.
Installation in accordance with this manual, applicable codes, and the
instructions of the authority having jurisdiction is mandatory.
While every precaution has been taken during the preparation of this manual
to ensure the accuracy of its contents, Clare Controls, Inc. assumes no
responsibility for errors or omissions.

HDBaseT Extender Set 100m User Guide 1
Introduction
HDBaseT Extender Set 100M is an HDMI/IR/RS-232 twisted pair extender that
includes one HDMI transmitter and one HDMI receiver. It is a professional 1×1
extender, with a single CAT5e cable. The input HDMI signal can be transmitted long-
distances, and the control signal (IR & RS-232) is capable of working bi-directionally.
The HDBaseT Extender can also support PoC, and with its Ethernet ports, it also
supports Internet access for use in a LAN.
Features
•HDBaseT technology
•High bandwidth: 10.2 Gbps
•Supports CEC
•Supports 3D
•Supports PoC
•HDMI/IR/RS-232 signal transmitted over single CAT5e/CAT6 twist pair
•Maximum transmission distance is up to 100 meters for all supported signals
•Supports Ethernet expanding
•HDTV-compatible, uses HDMI 1.4a and is HDCP-2.2 compliant
•Support 4K ×2K at 30 Hz, 1080P, 1080i, 720P, 576P, 576i, 480P, and 480i
•High-quality output video signal with 24bit/36bit deep color
•Bi-directional RS-232 control
•Bi-directional IR control
•LED indicators show work status
•Wall- or table-mount aluminum enclosure, PT case design
Package contents
•1x Tx100 transmitter
•1x Rx100 receiver
•4x mounting ears (separated from the transmitter and the receiver)
•1x power adapter (24 VDC, 3 A)
•1x power supply plug adapter kit
•2x RS-232 cable
•8x screws (3 ×6mm)
•1x user manual
Notes:Ensure all the accessories are included. If not, contact your dealer.

2 HDBaseT Extender Set 100m User Guide
Product appearance
Figure 1: The Tx100 transmitter
(1) ON
Working status indicator of this device. When the transmitter is on and
working properly, the green LED blinks.
(2) LINK
HDBaseT link status indicator, green LED. It remains illuminated when
the device has a connection.
(3) IN
The LED remains illuminated when connected to a device that supports
HDCP and is working normally. The LED blinks when the device does
not support HDCP.
(4) POWER LED
The red LED illuminates and stays on when power is connected.
(5) ETHERNET
Built-in Ethernet connectivity. Connect any of the Ethernet ports found
on the transmitter or receiver for Internet access and to feed your
IP-enabled devices. You can also connect to an existing LAN to
integrate all IP-enabled devices connected to the Extender Set. When
properly connected, the yellow LED indicators blink and the green
indicators remain illuminated.
(6) HDBT OUT
Connects to the HDBaseT port on the receiver via a single Cat5e/Cat6
cable.
(7) HDMI IN
Connects to the HDMI source device.
(8) IR IN
Infrared signal input. Collects infrared signals to be sent via HDBaseT to
the receiver (Rx) IR OUT.
(9) IR OUT
Infrared signal input. Outputs infrared signals received from the receiver
(Rx) via HDBaseT.
(10) RS-232
RS-232 connector. Supports bi-directional RS-232 communication.
(11) 24 VDC
Connects to the power supply. (Not necessary if the receiver connects
with a power adapter.)
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10)(11)

HDBaseT Extender Set 100m User Guide 3
Figure 2: The Rx100 receiver
(1) ON
Working status indicator of this device. When the receiver is on and
working properly, the green LED blinks.
(2) LINK
HDBaseT link status indicator, green LED. It remains illuminated when
the device has a connection.
(3) OUT
The LED remains illuminated when connected to a device that supports
HDCP and is working normally. The LED blinks when the device does
not support HDCP.
(4) POWER LED
The red LED illuminates and stays on when power is connected.
(5) ETHERNET
Built-in Ethernet connectivity. Connect any of the Ethernet ports found
on the transmitter or receiver for Internet access and to feed your
IP-enabled devices. You can also connect to an existing LAN to
integrate all IP-enabled devices connected to the Extender Set. When
properly connected, the yellow LED indicators blink and the green
indicators remain illuminated.
(6) HDBT IN
Connects to the HDBaseT port on the receiver via a single Cat5e/Cat6
cable.
(7) HDMI OUT
Connect to the HDMI display device.
(8) IR IN
Infrared signal input. Collects infrared signals to be sent via HDBaseT to
the transmitter (Tx) IR OUT.
(9) IR OUT
Infrared signal input. Outputs infrared signals received from the
transmitter (Tx) via HDBaseT.
(10) RS-232
RS-232 connector. Supports bi-directional RS-232 communication.
(11) 24 VDC
Connects to the power supply.
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10)(11)

4 HDBaseT Extender Set 100m User Guide
Twisted pair cable connection
The Cat5e/Cat6 terminations for HDBaseT devices should be a straight thru TIA/EIA
T568B standard. TIA/EIA T568A standard is not recommended.
Table 1: T568A and T568B cable standards
TIA/EIAT568A
TIA/EIAT568B
Pin
Cable color
Pin
Cable color
1
green white
1
orange white
2
green
2
orange
3
orange white
3
green white
4
blue
4
blue
5
blue white
5
blue white
6
orange
6
green
7
brown white
7
brown white
8
brown
8
brown
1st Ground
4-5
1st Ground
4-5
2nd Ground
3-6
2nd Ground
1-2
3rd Group
1-2
3rd Group
3-6
4th Group
7-8
4th Group
7-8
Note: RJ45 EZ connectors should not be used at any time.