Clarion UNGO MS3200 User manual

MS3001_owner's.qxd 9/10/99 5:27 PM Page 1

Congratulations on your purchase of the Ungo Security System.
This Ungo Security System was designed in the heart of
California’s high-tech “Silicon Valley” by Ungo Security
Corporation, a subsidiary of Clarion Corporation. Since its founding in
1975, Ungo has been recognized as a pioneer and long time industry
leader in vehicle security.
Please read this manual thoroughly to familiarize yourself with your
system’s components and operation. Discuss any questions you might
have with your installing dealer.
Record the serial number of your Ungo system and keep all dealer
records and receipts. Be sure to discuss the installation with the dealer
so that you understand the specifics of the installation in your vehicle.
Also, do not forget to complete and mail the Product Warranty
Registration Card within 60 days of purchase and insure that the
installing dealer has stamped and signed the appropriate section in
order to properly register your warranty.
MS3001_owner's.qxd 9/10/99 5:27 PM Page 2

Table of Contents
1. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1
2. Remote Transmitters
Remote Transmitter Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2
Two Car Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
Adding a New Transmitter into the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 4
Deleting Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 4
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 5
3. Basic Operation
Remote Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
Remote Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Tamper Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Silent Arming / Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
Arming Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8
Passive Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8
Panic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8
Emergency Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
Automatic System Rearming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
Full Time System Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
4. Other Features
Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 10
Ignition Controlled Door Locking / Unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 10
Dome Light Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 10
Auxiliary Function Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 11
Remote Car Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12
Garage Door Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12
Additional Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12
5. Reference Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13
6. Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14
7. Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 15
Note: Certain features described in this manual may require additional parts and/or labor. Also, many features of
the Ungo MS3001 / MS3200 security systems have selectable options that must be activated or programmed
during the system’s installation. These items will be identified in the following sections. Your Authorized
Ungo Dealer will be happy to discuss these features with you and help you design your system to meet your
needs.
MS3001_owner's.qxd 9/10/99 5:27 PM Page 3

Ungo Security Systems are state-of-the-art vehicle protection systems equipped with features
designed to:
❐
Deter potential intrusions to the vehicle by continually flashing the system LED status
indicator while the system is Armed, giving a visual indication to any passer-by that the
system is equipped with a security system.
❐
Detect intrusions to the vehicle, including impacts to the vehicle’s body and glass, and
opening of the doors, trunk and hood.
❐
Alert those in the vicinity of the vehicle by sounding the system’s siren and flashing,
parking lights, and honking the horn.
❐
Inform the owner when the system has been triggered and specifically which zone was
violated. The system will also inform the user of any bad switches or sensors that may
be causing the system to function improperly.
❐
Protect both you and the contents of your vehicle with features such as panic mode,
dome light illumination, and ignition controlled door locking.
Each Ungo MS3001 / MS3200 System comes with:
• Main Unit - the “brain” of the system.
• 2 - Three Button Remote Transmitters
• Siren (MS3001) - Water resistant, high output siren that sounds when system is
triggered.
•Battery Back-up Siren (MS3200) - Water resistant, self contained, battery back-up siren
that sounds for up to 1 full hour when system is triggered or if the siren becomes
disconnected from it’s source of power.
•Status LED - red illuminated indicator that provides system status information.
• Emergency Override / Valet Switch - used to override the system in case the Remote
Transmitters become lost or stolen. Also used to temporarily disable the system when the
vehicle is being serviced or turned over to a parking attendant.
Options and Convenience Features*
The advanced design of the Ungo system incorporates a number of optional inputs and outputs
allowing you to create a customized security / convenience system by easily accommodating
many optional convenience and security features such as:
*May require additional parts and/or labor, see store for details.
About Your Ungo Security System
MS3001/MS3200Owner’sManual - Page 1
❐Remote Door Locking
❐Starter Disable
❐Horn Honk
❐ Illuminated Entry / Exit
❐ Remote Window Control
❐Remote Car Start
❐ Extended Range Antenna
❐Power Trunk / Hatch Release
❐ Glass Breakage Sensor
❐Radar Sensor
❐Garage Door Receiver
❐Auxiliary Lighting Control
❐Stereo System Valet
❐Remote Head Lamp Control
❐ Back-up Battery Siren
MS3001_owner's.qxd 9/10/99 5:27 PM Page 1

Remote Transmitter Layout
Each MS3001 / MS3200 system comes with 2 multifunction Remote Transmitters used to control
nearly all of the system’s features.
Each time a transmitter button is pressed, the LED will flash to indicate that a transmission is
taking place.
Button 1 Arms and Disarms the system. This Button also locks and unlocks the doors when the
system is in Valet Mode.
Button 2 controls the system’s Auxiliary Function 1, which is normally used for activating a car’s
electric trunk release.
When Button 1 and 2 are pressed together, the system will Arm or Disarm
silently (without chirp
confirmation).
As an option, your installer can set system to always arm without chirp confirmation. If this is done, then
pressing Buttons 1 and 2 together will Arm or Disarm the system with chirp confirmation.
The Mode Button will change the function of Buttons 1 and 2 when it is pressed, allowing
Buttons 1 and 2 to control the system’s Auxiliary Function Outputs.
Note also that the LED on the transmitter turns green when the Mode Button is pressed to
indicate the current function of Buttons 1 and 2. The LED will stay on for 5 seconds, then turn
off, returning Buttons 1 and 2 to their default settings.
It is also possible to set individual Remote Transmitters to arm and disarm the system using any
of the Transmitters function Buttons, which is extremely useful when a Transmitter is used to
control multiple systems. See
Adding a Remote Transmitter into the System.
Remote Transmitters
Button 1
Button 2
Mode Button
LED
Page2 - MS3001/MS3200Owner’sManual
MS3001_owner's.qxd 9/10/99 5:27 PM Page 2

The following diagram illustrates how the Remote Transmitter controls the functions of the
system:
Two Car Operation
If you want to control two or more Ungo Security systems by a single Remote Transmitter, the
unused functions of the Remote Transmitter can be set up by your dealer to operate another
Ungo Security system, giving you the convenience of operating multiple vehicles from a single
Remote Transmitter.
When set for two car operation, the Remote Transmitters will function as in the example below:
For more information about Two Car operation, see your Authorized Ungo Dealer.
MS3001/MS3200Owner’sManual - Page 3
ARM/DISARM
AUX 1
AUX 2
MODE
green
MODE
none
BUTTON 1
BUTTON 2
MODE BUTTON Mode Sequence
not used
(A) = Car 1
(B) = Car 2
ARM (A) ARM (B)
AUX 1(A)
MODE
green
MODE
none
BUTTON 1
BUTTON 2
MODE BUTTON Mode Sequence
MS3001_owner's.qxd 9/10/99 5:27 PM Page 3

Page4 - MS3001/MS3200Owner’sManual
Adding a New Transmitter into the System
The MS3001 / MS3200 has the ability to recognize up to 21 individual Remote Transmitters. If
the vehicle is used by multiple drivers, each can have their own Remote Transmitter.
To add Remote Transmitters:
1. Turn on the ignition.
2. Press and hold the Override switch.
•The status LED will turn on red.
3. Within 5 seconds:
Continue holding the Override switch and Press Transmitter Button 1*
For remote arming with chirp confirmation.
--- or ---
Release the Override switch and Press Transmitter Button 1*
For remote arming without chirp confirmation.
•The status LED will flash once quickly to confirm that the new Remote Transmitter
has been added.
4. Turn off the ignition.
* The Button that is pressed will be the Arm/Disarm Button on that Remote Transmitter. You may program any of the
Transmitter’s function buttons to arm and disarm the system at this point.
Deleting Transmitters (Adding a Remote Transmitter and Erasing All
Other Remote Transmitters From the System)
1. Turn on the ignition.
2. Press and hold the Override switch.
•The status LED will turn on red.
Continue to hold the Override switch.
•After 5 seconds, the status LED will flash 4 times, then turn on red again.
3. Within 5 seconds:
Continue holding the Override switch and Press Transmitter Button 1*
For remote arming with chirp confirmation.
--- or ---
Release the Override switch and Press Transmitter Button 1*
For remote arming without chirp confirmation.
•The status LED will flash once quickly to confirm that the new Remote Transmitter
has been added.
4. Turn off the ignition.
* The Button that is pressed will be the Arm/Disarm Button on that Remote Transmitter. You may program any of the
Transmitter’s function buttons to arm and disarm the system at this point.
MS3001_owner's.qxd 9/10/99 5:27 PM Page 4

MS3001/MS3200Owner’sManual - Page 5
Battery Type: 23A
Battery Replacement
Your Ungo Remote Transmitter uses a 12 volt alkaline battery, which will need to be replaced
from time to time. Under normal conditions, the battery should last for up to a year before it
needs replacement.
When your Remote Transmitter’s battery is in need of replacement, you will notice a decrease in
your system’s operating range or a decrease in the brightness of the Transmitter’s LED indicator.
To change the battery, remove the 2 screws at the back of the Transmitter and carefully separate
the top and bottom halves of the Transmitter case.
Insert the new battery, making sure that the positive and negative terminals are positioned
correctly and replace the cover.
MS3001_owner's.qxd 9/10/99 5:27 PM Page 5

Page6 - MS3001/MS3200Owner’sManual
Remote Arming
When Armed, the system monitors and protects 5 independent areas, or zones , including the
ignition switch, doors, hood/trunk, Shock Sensor, and an optional sensor.
To Arm the System:
1. Turn off the ignition.
2. Press Button 1.
•The siren will chirp once.*
•The doors will lock.
•The parking lights will flash once.
•The LED will turn on red, indicating the ignition, doors, hood and trunk inputs are
activated.
* The siren chirp(s) during Arming will alert you the condition of the system and vehicle when the system is
armed.
1 chirp = normal arming
1 + 3 chirps = Shock Sensor sensitivity is off
1 + 4 chirps = door, hood, or trunk open
During Arming, if the system detects a bad sensor or an open zone, the system will ignore that input, but keep
all other areas protected.
3. After 20 seconds:
•The LED will begin blinking, indicating that the sensor inputs are activated.
While the system is Armed, the system will trigger if:
• The ignition key is turned on.
• The doors are opened.
• The Shock Sensor detects an impact to the vehicle or the motion of the car being raised.
• The hood or trunk is opened.
• A connected optional sensor is disturbed.
When triggered, the siren will sound, the horn will honk, and the parking lights will flash.
If the same input triggers the system 3 times during a single arming cycle, the system will
bypass that input, keeping the other zones protected, until the next time the system is
armed.
If the Shock Sensor detects a light impact to the car or a connected optional sensor triggers
the system’s Warn Away input, the siren will sound a chirp to warn away the potential
intruder.
Basic Features
MS3001_owner's.qxd 9/10/99 5:27 PM Page 6

MS3001/MS3200Owner’sManual - Page 7
Remote Disarming
To Disarm the System:
Press Button 1.
•The siren will chirp twice.*
•The doors will unlock.
•The parking lights will flash twice.
•The dome light will turn on.
•The LED will turn off.
* The siren chirps during disarming will alert you if the system had been triggered while armed.
2 chirps = normal disarming
1 long chirp + 1 short chirp = Tamper Alert - system was triggered
Tamper Alert
On Disarming, if the system responds with one long chirp and one short chirp, indicating the
system was triggered, the LED will flash for 60 seconds to indicate the zone that triggered the
system.
LED Flashes (60 seconds):
1 flash = door
2 flashes = Shock Sensor
3 flashes = optional sensor
4 flashes = hood / trunk
example: flash-flash-pause-flash-flash-pause = Shock Sensor
Silent Arming / Disarming
Each Remote Transmitters can be individually set to Arm and Disarm the system with or without
chirp confirmation at the time they are programmed into the system (see Adding a New
Transmitter into the System).
To temporarily cancel the Arming and Disarming confirmation chirps, you can Arm or Disarm the
system by pressing Buttons 1 and 2
together .
Note: The confirmation chirps will only be cancelled if the system status is normal. The chirp indications for the open
zone warning will not be cancelled when the system is Armed or Disarmed silently .
MS3001_owner's.qxd 9/10/99 5:27 PM Page 7