Clarke CMS650 User manual
USER INSTRUCTIONS
ORIGINAL INSTRUCTIONS GC1017 ISSUE 2
MOBILE SWEEPER
MODEL NO: CMS650 /CMS850
PART NO: 6470355/ 6470357
2
INTRODUCTION
Thank you for purchasing this CLARKE Mobile Sweeper.
Before attempting to operate the product, it is essential that you read this
manual thoroughly and carefully follow all instructions given. In doing so you
will ensure the safety of yourself and that of others around you, and you can
also look forward to the product giving you long and satisfactory service.
GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a period of
12 months from the date of purchase. Please keep your receipt as proof of
purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
TECHNICAL SPECIFICATIONS
CMS650 CMS850
Operating Width 65 cm 85 cm
Recommended operating speed 4 km/h 4 km/h
Collection Box Capacity 0.14L 0.30L
Net Weight 8.6 kg 12 kg
Dimensions L x W x H 660 (handle folded)
x 650 x 265 mm
840 (handle folded)
x 850 x 270 mm
3
SAFETY PRECAUTIONS
1. Failure to heed these warnings may result in damage to the equipment or
personal injury.
2. Never tamper with the product or modify it in any way, as this could prove
to be dangerous and will invalidate the guarantee. Only use the product
for the purpose for which it is intended.
3. Ensure that the sweeper is in good working order. Have any damaged
parts repaired or replaced immediately. Use genuine Clarke parts only. The
use of unauthorised parts may be dangerous and will invalidate the
guarantee.
4. Only use the sweeper in a suitable, well lit work area.
5. Keep the work area clean and tidy and free from unrelated items.
6. Only use the sweeper on level and solid ground.
7. Keep bystanders away whilst the sweeper is in use.
8. Never climb on, or attempt to ride on the sweeper.
9. Take care not to trap fingers in the moving parts of the sweeper.
10. Do not over-reach. Keep your proper footing and balance at all times.
11. Safety equipment such as non-skid shoes and dust mask may reduce
personal injuries.
4
UNPACKING & ASSEMBLY
Unpack the components from inside the collection box onto a clean flat area
and ensure that all parts are present according to the packing list below:
Visually inspect all components to ensure that no damage was suffered in
transit. Any deficiencies should be reported to your CLARKE dealer
immediately.
1. With the sweeper upside down,
take the small screws and use
three to attach each of the
rotating brushes to the underside
of the sweeper.
1 1 x Lower Handle 5 2 x Handle Support Brackets
2 1 x Upper Handle 6 2 x Coachbolts
3 2 x Rotating Brushes 7 2 x Plastic Spacers
4 4 x Handle Fixing Knobs 8 1 x Packet of Screws
5
2. Turn the sweeper over and fit the
handle support brackets into the
slots, using the two large screws.
3. Attach the lower handle to the
support brackets using the fixing
knobs. Push the handle down so
the fixing pegs hold the handle
upright & tighten the knobs.
• The handle assembly can be
folded flat to the sweeper body
for storage. Raise the handle off
the fixing pegs shown and tilt
forward.
4. Add the upper handle to the
lower handle using the two
coachbolts, plastic spacers, and
remaining handle fixing knobs.
• The upper handle height can be
adjusted by unfastening the fixing
knobs and repositioning the
handle using different fixing holes.
USE AND CARE
1. The ride height can be adjusted
by twisting the height adjustment
control. Twist clockwise to raise
the height and anti-clockwise to
lower.
2. If using in dusty areas, try to sweep
upwind of the dusty material
being swept up. Wear a dust mast
if dust is being created in the
atmosphere.
3. Only use mild soap and a damp cloth to clean the outside of the sweeper.
Keep metal parts dry to minimise corrosion. Store in a dry place out of
reach of children.
6
COMPONENT PARTS DIAGRAM
7
COMPONENT PARTS LIST
PART NO DESCRIPTION PART NO DESCRIPTION
1 M6 Locknut 27 Inner wheel
2 6 dia washer 28 Steel Sleeve
3 Screw 29 Washer
4 Round Brush 30 Rubber Drive Belt
5 Pulley Wheel 31 Screw M6x8
6 Screw 32 Handle Support Bracket RH
7 Brush Support 33 M10 Nut
8 Bearing 608 34 Swivelling Castor Wheel
9 Bearing Cover 35 Castor Wheel Carrier
10 Spindle 36 Height Adjustment Screw
11 Bearing 37 Main Body
12 Screw 38 Bolt
13 Screw 39 Height Adjuster Knob
14 Roller Connector 40 Collection Box
15 Screw 41 Collection Box Cover
16 Roller Support-RH 42 Collection Box Handle
17 Bearing 43 Upper Handle
18 Belt Pulley 44 Coachbolt M8x30
19 Roller Spindle 45 Handle Fixing Knob
20 Rubber Drive Belt 46 Lower Handle
21 Wheel Cover 47 Rear Guard
22 Tyre 48 Handle Support Bracket LH
23 Bolt M10x65 49 Rubber Drive Belt
24 Spring Washer 10 dia 50 Roller Spindle
25 Washer 51 Roller Support LH
26 Wheel Boss 52 Roller Brush
This manual suits for next models
3
Table of contents
Other Clarke Blower manuals
