Clarson PUBLIC III GN9330e User manual

PUBLIC III
GN9330e Wireless Headset System
Service and
Installation Instructions
Clarson Apparatebau GmbH
Zeppelinstr. 4 78083 Dauchingen
Postfach 11 63 78080 Dauchingen
Tel.: [phone]
Fax: [phone]
Email: [e-mail]
Internet: http://www.clarson.de
Technical modifications reserved 10/2014
Components of the GN9330e Headset System
Wireless headset system cpl.
comprising:
Base station, headband and
earhook
incl. patch cable 40.054.376
Replacement headset
- WITHOUT base station
- WITHOUT wearing accessories -
Earhook
Headband

Central Unit
Ref. 40.054.311
RJ 45
8-olig
RJ 45
8 pin
Microphone Loudspeaker Unit
Ref. 40.054.301 - bottom side
Standard Connection of the GN9330e Headset System
to the microphone loudspeaker unit PUBLIC III
- SERVICE SIDE -
RJ 10
4 pin
RJ 45
8 pin
RJ 10
8 pin
Ref. 40.054.327 patch cable, 3 m
with RJ45 connector (8/8-pin),
central unit <—> microphone loudspeaker unit
Ref. 40.054.376 patch cable, 3 m
with RJ10 connector (4/4-pin),
microphone loudspeaker unit <—> GN9330e base station
2
RJ 45
8 pin
RJ 10
4 pin

13
RJ 10
4 pin
22
11
17
9
Pos. A
16
RJ 45
8 pin
9
7
Base Station Headset
Microphone
Volume control with mute
Switchover button to headset mode
Configuration switch to pos. A
Connection to PUBLIC III central unit
40.054.311 (to microphone loudspeaker
unit 40.054.301 respectively), pages 2/3/4
A/C power adapter port
Microphone volume
Power supply adapter
1
5
6
9
11
13
17
22

13
22
11
9
17
Pos. A
16
Pairing button XW
16
10
Headset charge facility
10
Base station
18
1
5
6
XW
18
Wireless headset
Ref. 40.030.022

6 3
Central Unit
Ref. 40.054.311
Optional Connection of the GN9330e Headset System
to the Central Unit PUBLIC III
- SERVICE SIDE -
RJ 45
8 pin
Microphone Loudspeaker Unit
Ref. 40.054.301 - bottom side
RJ 45
8 pin
Ref. 40.054.378 patch cable, 3 m
with RJ45/RJ10 connector
(8/4-pin),
central unit <—> GN330e base
station
Attention: Cable must be ordered
separately!!!
RJ 45
8 pin

13
RJ 10
4 pin
22
11
9
17
Pos. A
16
RJ 10
4 pin
RJ 45
8 pin
1
5
6
10

13
22
11
9
17
Pos. A
16
Wireless headset
Ref. 40.030.022
Pairing of one/several Headset(s) to the GN9330e Base Station
If one of more additional headsets shall be operated from one GN9330e base
station, they need to be paired as follows:
Important:
Make sure that the connection between primary headset and base station is
established.
Push the headset´s speech button .
The base´s Telefone and USB mode indicators should not flash.
A secondary headset is paired as follows:
1. Place secondary headset in primary headset´s base
2. Push pairing button XW at the base station.
Primary base´s telephone and USB mode indicators and secondary
headset´s link indicator will light for 2 seconds.
This means that the secondary headset has been paired successfully
(see also page 16 of the GN9330e user manual)
6
10
16

4
Standard Connection of the GN9330e Headset System
to the Central Unit PUBLIC III
- PUBLIC SIDE -
Central Unit
Ref. 40.054.311

13
RJ 10
4 pin
22
11
9
17
Pos. A
16
RJ 10
4 pin
5
Operating Instructions

1. Factory Settings at the GN9330e Base Station:
Speech volume on approx. 1 o´clock
Configuration dial on „A“
2. Link socket of the headset´s base station with headset interface

of the PUBLIC III microphone loudspeaker unit (patch cable
40.054.376)
or
directly with the PUBLIC III headset socket of the central unit
(patch cable 40.054.378)
3. Connect power supply to base station socket .
4. Switch on the PUBLIC III microphone loudspeaker unit (button ).
5. Remove headset from base station or push button :
xLED above button of the microphone loudspeaker unit flashes
xheadset is activated
6. Back to standard operating mode:
xInsert headset into base station or push button .
xSwitch the PUBLIC III microphone loudspeaker unit off and on again
(button ).
7. For all other functions please refer to the PUBLIC III service and installation
instructions as well as to the GN9330e user manual.
1322
11
17
6
10 6
9