Classic Exhibits visionary DESIGNS MOD-1272 Workstation Manual

© 2019
Order #XXXXX
Top View
Perspective View Side View
MOD-1272 Workstation
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2019
Order #XXXXX General Information
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED

© 2019
Step 1 of 2
Order #XXXXX Workstation Assembly
8
8
7
1
9
6
5
2
3
4
Infill
Infill
Infill
Item
1
2
3
4
5
6
7
8
9
10
--
--
--
Qty.
1
1
1
1
1
1
1
2
1
1
1
2
3
Description
Base Plate
48” S40 Vertical Extrusion w/ Stopper
48” S40 Vertical Extrusion
2.5” Angle-Cut Extrusion
48” S40 Vertical Extrusion
44” S40 Vertical Extrusion
8.747” Z45 Horizontal Extrusion
8.747” Z45 Horizontal Extrusion
37.75” RS500 Vertical Extrusion
Flange Plate
Sign
Wing
Infill
Steps:
1) Attach [4] to [3]. See Extrusion Attachment detail.
2) Attach [2] [5] and [9] to base plate [1], using bolts.
3) Attach [3] to [2] and [6] to [5].
See Extrusion Connector detail.
4) Slide lower infill between assemblies to rest on
stopper in vertical [2].
5) Secure infill with horizontal [7].
6) Slide center infill between assemblies to rest on
attached horizontal [7].
7) Secure infill with horizontal [8].
8) Slide top infill between assemblies to rest on
attached horizontal [8].
9) Secure infill with horizontal [8]
10) Attach sign to vertical [6], using screw caps.
See Sign Attachment detail.
11) Place wings into clamps. Tighten knobs to secure.
Sign
Screw Cap
Slide V4 into S40 then tighten set screw.
Secure sign to V4, using screw cap.
Sign Attachment
S40
V4
*
Set Screw
Set Screw
V26
Connector
Extrusion Connector
Slide upper extrusion
over V26 connector and
rest on lower extrusion.
Secure with set screws.
*
To prevent product loss,
keep all screws attached
to connector after
disassembling.
Keep clamps attached to [2] [3] [5] and [6].
Keep V26 connectors attached to extrusions [2] and [5].
*
*
*
Sign
Standoff
Clamp
Wing
Wing
*
Set Screw
Connector
Back View of Backwall
Insert connector into groove
of vertical extrusion, then
tighten set screw to secure.
Velcro
Extrusion Attachment
*

© 2019
Step 2 of 2
Order #XXXXX Workstation Assembly (Cont’d)
Completed Assembly
Steps:
1) Attach counter to [9] and [7].
See Counter Attachment detail.
2) Attach monitor mount to [3] and [6].
See Monitor Mount Attachment detail.
3) Route monitor cord through conduit. See
PR63 Attachment detail.
Thumb
Screws
Counter
10
9
7
Wing
Nut
Wing
Nut
Bolt
Attach [10] to [9], using bolt. Place fixed screws of counter into holes of [10]
then secure with wing nuts. Secure back of counter to horizontal [7], using
thumb screws.
Counter Attachment
*
6
3
Fixed
Bolts
Bolt
Mount
Plate
Monitor
Mount
Slide connectors into groove of extrusions
[3] and [6]. Tighten set screws to secure
connectors in place. Attach mount plate to
connectors, using bolts. Hang monitor mount
on fixed bolts of mount plate.
Monitor Mount
Attachment
*V4 Connectors
Counter
Monitor
Mount
*
*
pinch
PR63 Attachment
PR63 Conduit
PR63
Top View
Route cord through
conduit. Attach conduit
to back side of verticals
by pinching the opening
then inserting into the
groove of extrusion.
S44
Attach [10] to fixed screws on counter, using wing nuts, when packing.