Classic Exhibits visionary DESIGNS MOD-1331 Manual

© 2023
Order #XXXXX MOD-1331 Workstation
Completed Assembly
Item
1
2
3
4
5
--
Qty.
1
1
2
1
2
3
Description
Base Plate
48” Q914 Vertical Extrusion
38” Z45 Vertical Extrusion
25” Q914 Vertical Extrusion w/ Cap,
Clamps, and Connector
Flange Plate
Shelf
Counter Attachment
*
Wing Nut
Fixed
Screws
Flange
Plate [5]
3
3
Counter
Attach flange plates to extrusions [4], using
screws. Insert fixed screws, on counter, into
holes of flange plate then secure with wing
nuts. Secure back of counter, using thumb
screws.
Keep connector with set
screws attached to [2]
when packing.
Large
Graphic
Thumb
Screw
Shelf
Shelf
Shelf
Connector
2
1
33
4
3
32
5
5
Small
Graphic
Counter
*
Tighten set screw to
secure A10 to [4].
Tighten knob to secure
graphic to A10 Clamp.
A10 Clamp
*
Bolts
Monitor Mount Attachment
*
*
*
*
Attach Monitor Mount back piece to
vertical extrusion using bolts & nuts.
Monitor Mount
Back piece Slide monitor mount
into back piece.
V4
Connectors
Slide connectors into groove of extrusion. Tighten
set screws to secure connectors in place. Attach
monitor mount back plate to extrusion, using bolts.
A10
Clamp
Keep A10 clamps attached
to [4] when packing.
Curved
Graphic
Steps:
1) Attach lower verticals [2] and [3] to base plate [1], using bolts.
2) Attach upper vertical [4] to lower vertical [2], using connector.
3) Attach shelves to vertical [2].
4) Attach large graphic to verticals [3], using screw caps.
See Large Graphic Attachment detail.
5) Attach flange plates [5] to tops of verticals [3], using bolt.
6) Attach counter to flange plates [5] vertical [2], using wing nuts
and thumb screws. See Counter Attachment detail.
7) Attach small and curved graphics to [4], using A10 clamps.
See A10 Clamp detail.
8) Attach monitor mount to [4]. See Monitor Mount detail.
Screw
Cap
Graphic
Screw
Cap
Slide V4 into Z45 then tighten set screw.
Secure graphic to V4, using screw cap.
Large Graphic
Attachment
Z45
V4
*
*
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2023
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2023
Order #XXXXX
Level 1 Level 2 Level 3 Level 4
Top View of Each Level
Level 5
1
Small
Graphic
Large
Graphic
4
5
5
3,3
2
Shelf
Shelf
Shelf
Counter Top
Monitor
Mount
Setup
Hardware
Curved
Graphic
Case Packing