Classic Exhibits VISIONARY DESIGNS VK-1128 Manual

© 2024
Order #XXXXX
Locked layer contains
placeholder marks.
Plan View
Elevation View
10’
10’
VK-1128 10’x10’ Booth
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2024
Order #XXXXX
Locked layer contains
placeholder marks.
= 1 sq foot
Plan View

© 2024
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
LADDERS OR LIFTS
MAY BE REQUIRED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
Controlling the RGB LED lights
Function of Keys
Receiver:
1. Working voltage: DC12V/24V
2. Output: Max. 6A/Channel
Total output Max. 10A
3. Max standby power: 0.5W
Remote Control:
1. Working voltage: 3V
2. Standby power: <20uA
3. Transmitting power: 6dBm
Specifications:
Static Mode:
1. Use the Color Ring key to select a color.
2. Saturation is controlled with W/R/G/B keys.
3. White mode is available by long-pressing ‘ON’ key.
4. Colors (not white) are dimmable with the
Brightness key.
Dynamic Mode:
Press "M" key to cycle through the following options:
1. White light fades in and out.
2. Several colors fade in and out.
3. R,G,B three colors fade in and out.
4. R,G,B three colors flash.
5. Six colors flash.
6. Random color flashes.
7. Red color fades in and flashes.
8. Green color fades in and flashes.
9. Blue color fades in and flashes.
To Pair a Remote with Multiple Units:
1. Power on the lights.
2. Press ‘ON’ key within 3 seconds.
3. Lights will blink when link is made.
To unpair: Long press ‘ON’ key within 3 seconds
after switching on lights.
Remotes can be paired with one or more receivers.
Different receivers can work synchronously even
when started at different times (within 30 min).
Master ON
Mode (M)
White +/-
Red +/- Green +/-
Blue +/-
Brightness - Brightness +
Color Ring
W R G B
ON
S- M S+
OFF
Indicator
Master OFF
Speed - Speed +
General Information

© 2024
Order #XXXXX
+
-Female
++
--
Lights Male
Light to Light Attachment
Maximum of 5 lights
per Transformer
RGB Controller Attachment
Connect transformer
to RGB Controller,
then connect transformer
to power source.
RGB Controller
Power Transformer
48W / 2 Amp / 24V
+
-
Power
Female
Light to Tranformer Attachment
Transformer
48W / 2 Amp / 24V
+
-Female
++
--
Lights Male
Light to Light Attachment
Maximum of 9 lights
per Transformer
RGB Controller Attachment
Connect transformer
to RGB Controller,
then connect transformer
to power source.
RGB Controller
Power Transformer
96W / 4 Amp / 24V
+
-
Power
Female
Light to Tranformer Attachment
Transformer
96W / 4 Amp / 24V
+
-Female
++
--
Lights Male
Light to Light Attachment
Maximum of 14 lights
per Transformer
RGB Controller Attachment
Connect transformer
to RGB Controller,
then connect transformer
to power source.
RGB Controller
Power Transformer
144W / 6 Amp / 24V
+
-
Power
Female
Light to Tranformer Attachment
Transformer
144W / 6 Amp / 24V
Supernova Lighting

© 2024
Crate 1 of 1
Order #XXXXX
Locked layer contains
placeholder marks.
CRATE PACKING
Crate Packing

© 2024
Step 1 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
Item
A
B
F1
F2
Qty.
1
1
1
1
Description
48”w x 48”h x 12”d Cabinet
48”w x 48”h x 12”d Cabinet
70”w x 45”h x 4”d Wall Panel
70”w x 45”h x 4”d Wall Panel
Steps:
1) Connect Cabinets [A] & [B] together using roto cam locks.
See Roto Cam Lock Connection detail.
2) Assemble Wall Panels [F1-F2] together using roto cam locks.
See Roto Cam Lock Connection detail.
3) Use bolts to connect Wall Panel [F1] to nut serts on side of
Cabinet [B]. See Bolt to Nut Sert Connection detail.
*Bolt to Nut Sert
Connection
nut
sert
bolt
Roto Cam Lock Connection
*
Place hex tool in hole on side of panel. Rotate
to activate lock & secure panels together.
Hole
Lock
Hex Key Tool
Step 1
Hex Key Tool
Lock
Step 2
*
*
*
A
B
F1
F2
**
*
*
Assembly

© 2024
Step 2 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Standoffs &
Screw Caps
Plex Panel
Plex Panel
BACK VIEW
Item
C
D
Qty.
1
1
Description
48”w x 48”h x 12”d Cabinet
48”w x 48”h x 12”d Cabinet
Steps:
1) Attach plex panels inside of Cabinets [C] and [D], using standoffs
and screw caps. .
2) Connect Cabinets [C] & [D] together using roto cam locks.
See Roto Cam Lock Connection detail.
3) Use bolts and screw caps to connect Wall Panel [F2/F1]back of
Cabinets [C] & [D]. See Bolt to Nut Sert Connection detail.
C
D
D
F2
C
*
*
*
*
When assembled
Roto Cam Lock Connection
*
Place hex tool in hole on side of panel. Rotate
to activate lock & secure panels together.
Hole
Lock
Hex Key Tool
Step 1
Hex Key Tool
Lock
Step 2
**
*Bolt to Nut Sert
Connection
nut
sert
bolt
Screw Cap
Screw Cap
Screw Cap
Assembly (cont’d)

© 2024
Step 3 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
Steps:
1) Install Monitor Mount to backwall panels [F2].
See Monitor Mount Attachment detail.
2) Attach keyboard Shelf to backwall panels [F1],
See Roto Cam Lock Connection.
Keyboard Shelf
*
F2
F1
Hole for wire
management Attach Monitor Mount
to wall panel using bolts provided
*Monitor Mount Attachment
Bolt
Wall
Panel
Monitor
Mount
Roto Cam Lock Connection
*
Place hex tool in hole on side of panel. Rotate
to activate lock & secure panels together.
Hole
Lock
Hex Key Tool
Step 1
Hex Key Tool
Lock
Step 2
Attachments

© 2024
Step 4 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Steps:
1) Place Greeting Counter in front of backwall assembly, as shown on layout.
2) Connect power cords to Supernova lights inside Greeting Counter, as shown.
3) Attach power cords to Supernova lights inside Cabinets [A & B].
Transformers are permanently attached to the back side of panel [F1].
4) Connect power cords to Supernova lights inside Cabinets [C & D].
Transformers are permanently attached to the back side of panel [F1].
Note: Refer to the Supernova Lighting page for instructions.
Completed assembly
Greeting Counter
F1
BA
C
D
BACK VIEW
SIDE VIEW
Lights
Lights
Lights
Lights
Hole for wire
management Hole for wire
management
Hole for wire
management
To lights in
Cabinets
A & B
Lights
Lights
Lights
Lights
Cord Connection
Transformers
on back of panel
Transformers
(permanently attached
to Panel F1)
Transformers
(permanently attached
to Panel F1)
Transformer
F1
Hole for wire
management
Lights
Lights
Hole for wire
management
Wiring