Clean Logix BLX-100D User manual

USER
MANUAL
English (Original Instrucons)
Updated: 02/11/21
MODEL:
BLX-100D
Single Manual BootScrubber (Dry)

BLX-100D Manual Page 2 of 7 Updated: 02/11/21
USER MANUAL: BLX-100D
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
The BLX-100D is an all manual, single footwear
scrubbing unit. Designed and built as a solid member,
open stainless steel frame with a solid hand rail for
support. The BLX-100D features one removable sole
brush and four removable vercal side brushes, each
of which require no tools. Being a manual based,
dry unit the BLX-100D requires no electrical or water
connecons.
Overview
▪Frame - 304 Stainless Steel
▪Length - 28 in.
▪Width - 15 in.
▪Height - 44 in.
Specicaons
!
CAUTION:
1. Always follow plant and OSHA guidelines about
the use of hygiene equipment.
2. All personnel using this unit must be familiar with
the informaon contained in this manual. Follow
all installaon and maintenance instrucons.
3. Always wear appropriate footwear. Secure or
remove loose items on footwear.
4. Ensure solid foong and use both hands when
operang the unit.

BLX-100D Manual Page 3 of 7 Updated: 02/11/21
USER MANUAL: BLX-100D
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
GeneralInstallaonOperaonAppendix
Fig. 3.1: Rear mounng brackets
Installing and Mounng the Unit
1. Set unit in desired locaon.
2. Aspects to consider when deciding on placement:
• Clearance for entering and exing.
• Trac ow for unit operaon.
• Emergency exit paths or egress in case of
emergency.
• Head room for personnel while using the
unit.
3. Once the unit is in the desired locaon, use a
level to make sure the unit is stable and level in
all direcons. Make sure the locaon is a at
surface.
4. Using the 4 mounng brackets near each
corner, securely fasten the unit to the oor with
appropriate hardware for the given material (i.e.
concrete anchors and bolts) as shown in [Figures
3.1 and 3.2]
Installaon
Fig. 3.2: Front mounng brackets
!
WARNING
If not properly secured to oor the unit may p
over and has the potenal to cause personal injury.

BLX-100D Manual Page 4 of 7 Updated: 02/11/21
USER MANUAL: BLX-100D
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Installing Debris Tray
1. Plate the Debris Tray at the opening of the unit
and insert it underneath the frame. [Figure 4.1]
2. Make sure the tabs on the plate line up with the
holes on the unit, as shown in [Figure 4.2]
Installaon (connued)
Fig. 4.1: Inserng Debris Tray
Fig. 4.3: Brush clip rotaon for brush removal
Fig. 4.2: Aachment points for Debris Tray
Removing Brushes
1. The brushes are held in place by the brush clip at
the front of the unit.
2. To remove the brushes, pull up on the clip and
twist them outward, as shown in [Figure 4.3].
3. Once unlocked, the brushes can be removed for
cleaning, by slipping them out from their holders.

BLX-100D Manual Page 5 of 7 Updated: 02/11/21
USER MANUAL: BLX-100D
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
GeneralInstallaonOperaonAppendix
General Use
Prior to use - ensure brushes and debris tray are
secured and the system itself properly installed.
Before operang the unit, ensure solid foong and
use both hands on the handrail for support.
1. To begin operaon, step up to the unit and grip
the support handrail.
2. Place one boot in the unit.
3. Push the boot back and forth mulple mes so
every part makes contact with the brushes.
4. Once the rst boot is clean, remove it and repeat
the process with the second boot.
5. If boots are extremely dirty, it may be necessary to
scrub them mulple mes.
Cleaning and Wash-Down
1. Remove the Debris Tray and brushes from the
unit.
2. Brushes and Debris Tray can be washed,
individually, in a COP tank or wash machine
3. The frame can be washed down by convenonal
means.
Operaon
The following maintenance procedures are
recommended for normal use. Units which see a
high amount of daily use should be inspected more
frequently as necessary.
Weekly:
• Inspect brushes for damage or wear.
• Check for missing or deformed bristles.
• Ensure solid mounng to oor.
Monthly:
• Check all fasteners to ensure they are ght.
• Ensure warning labels and decals are present
and in good condion.
Quarterly:
• Inspect structure for cracked welds or bent
components.
Maintenance

BLX-100D Manual Page 6 of 7 Updated: 02/11/21
USER MANUAL: BLX-100D
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Appendix A - Parts Callout
Part No. Descripon
F1036 BOLT HHC 5/16-18 X 3/4 SS
M1262 BRUSH FIXED 10-1/2 X 3
M1388 BRUSH BOX WLDMNT
M1391 HANDLE WLDMNT BLX-100
M1392 BRUSH CLIP
Part No. Descripon
M1393 FIXED SIDE BRUSH
M1396 FRONT PLATE BLX MANUAL
M1739 DEBRIS TRAY BLX-100D
M1740 DEBRIS SHIELD BLX-100D
P1248 LABEL SLIP HAZARD

BLX-100D Manual Page 7 of 7 Updated: 02/11/21
USER MANUAL: BLX-100D
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
GeneralInstallaonOperaonAppendix
Appendix B - Dimensions