Clean Logix BLX-200W User manual

USER
MANUAL
English (Original Instrucons)
Updated: 02/11/21
MODEL:
BLX-200W
Dual Manual BootScrubber (Wet)

BLX-200W Manual Page 2 of 9 Updated: 02/11/21
USER MANUAL: BLX-200W
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
The BLX-200W is an all manual, single footwear
scrubbing unit. Designed and built as a solid member,
open stainless steel frame with a solid hand rail for
support. The BLX-200W features one removable sole
brush and four removable vercal side brushes, each
of which require no tools. Being a manual based, wet
unit the BLX-200W requires no electrical and is pre-
congured for easy plumbing of water and sanizer.
Overview
▪Frame - 304 Stainless Steel
▪Length - 29 1/2in.
▪Width - 28 in.
▪Height - 42 in.
Specicaons
!
CAUTION:
1. Avoid contact of cleaning agent with skin
and eyes. If contact occurs, see MSDS sheet
for further rst aid measures.
2. Follow safety instrucons of chemical
manufacturer (MSDS).
3. Always follow plant and OSHA guidelines
about the use of hygiene equipment.
4. All personnel using this unit must be
familiar with the informaon contained
in this manual. Follow all installaon and
maintenance instrucons.
5. Always wear appropriate footwear. Secure
or remove loose items on footwear.
6. Ensure solid foong and use both hands
when operang the unit.
▪Cold Portable Water
▪ 35 PSI Minimum Pressure
▪100°F Max Temperature
Water Requirements
NOTE: A back ow preventer must be installed
in the water line for this unit. Check local
codes to ensure proper installaon
!
WARNING:
DO NOT use ammable liquids (i.e. alcohol
based soluons or similar) without diluon.

BLX-200W Manual Page 3 of 9 Updated: 02/11/21
USER MANUAL: BLX-200W
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
GeneralInstallaonOperaonAppendix
Fig. 3.1: Verify level of bootscrubber at each end
Installing and Mounng the Unit
1. Set unit in desired locaon.
2. Aspects to consider when deciding on placement:
• Clearance for entering and exing.
• Trac ow for unit operaon.
• Emergency exit paths or egress in case of
emergency.
• Head room for personnel while using the
unit.
3. Once the unit is in the desired locaon, use a
level to make sure the unit is stable and level in all
direcons [Figure 3.1]. Make sure the locaon is a
at surface.
4. Using the 4 mounng brackets located at each
corner, securely fasten the unit to the oor with
appropriate hardware for the given material (i.e.
concrete anchors and bolts) as shown in [Figure
3.2]
5. Dosing of sanizing chemicals into water supply
can be accomplished via the included venturi
injector.
Installaon
Fig. 3.2: Mounng bracket locaons
WARNING
If not properly secured to oor the unit may p
over and has the potenal to cause personal injury.
NOTE: The unit is compable with most
common sanizers. For further plumbing
recommendaons please contact Clean Logix.

BLX-200W Manual Page 4 of 9 Updated: 02/11/21
USER MANUAL: BLX-200W
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Installing Handrail
Due to the shipment size, the BLX-200 will arrive with
the handrail disconnected.
1. Place handrail through the mounng brackets on
each side of the unit [Figure 4.1].
2. Using two 1/2” wrenches ghten the bolt through
the locknut unl the bolt booms out against the
handrail to secure in place [Figure 4.2].
3. Repeat for remaining bolts to secure the handrail
(8 bolts total).
Installaon (connued)
Fig. 4.1: Installing Handrail
Fig. 4.2: Handrail stablizaon bolts

BLX-200W Manual Page 5 of 9 Updated: 02/11/21
USER MANUAL: BLX-200W
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
GeneralInstallaonOperaonAppendix
Installing Foot Plate
1. Place the Foot Plates at the opening of each end
of the unit.
2. Make sure the notches on the plate line up with
the holes on the unit, as shown in [Figure 5.1].
Installaon (connued)
Fig. 5.1: Inserng Foot Plate
Plumbing
1. Connect the water regulator on the Venturi to the
water supply line (regulator thread = 1/2")
2. Using 3/8" OD polyethylene tubing (or similar)
connect the sanizer soluon to be used to the
Venturi's hose barb, as shown below:
NOTE: A back ow preventer must be installed
in the water line for this unit. Check local
codes to ensure proper installaon.

BLX-200W Manual Page 6 of 9 Updated: 02/11/21
USER MANUAL: BLX-200W
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Installaon (connued)
Fig. 6.1: Water line of BLX-200W
Fig. 6.2: Brush clip rotaon for brush removal
Removing Brushes
1. The brushes are held in place by the brush clip at
the front of the unit.
2. To remove the brushes, pull up on the clip and
twist them outward, as shown in [Figure 5.2].
3. Once unlocked, the brushes can be removed for
cleaning, by slipping them out from their holders.
Plumbing (connued)
3. Using the push to connect ng, connect the
Venturi system to the BLX's water line located
under the unit, near one of the foot plates
[Figure 6.1].
4. Test the system by stepping on the footplate to
engage the unit and begin spraying.
5. Adjust the soluon output as necessary using the
included metering ps (instrucons included).
NOTE: Injector must be mounted within 10 .
of boot scrubber.
!
WARNING:
DO NOT use ammable liquids (i.e. alcohol
based soluons or similar) without diluon.

BLX-200W Manual Page 7 of 9 Updated: 02/11/21
USER MANUAL: BLX-200W
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
GeneralInstallaonOperaonAppendix
General Use
Prior to use - ensure brushes, handrail, and foot plates
are secured and the system itself properly installed.
To verify water/sanizer supply; step on the Foot
Plate to iniate water/sanizer ow. Before operang
the unit, ensure solid foong and use both hands on
the handrail for support.
1. To begin operaon, step up to the unit and grip
the support handrails.
2. Enter the unit from either end, placing one boot in
the brush secon and the other on the opposing
foot plate to acvate the spray system.
3. Push the boot back and forth mulple mes so
every part makes contact with the brushes.
4. Once the rst boot is clean, remove it and walk
through to the second scrubber and repeat the
process with the other boot.
5. If boots are extremely dirty, it may be necessary to
scrub them mulple mes.
Cleaning and Wash-Down
1. Shut o water supply to unit and depressurize
water lines.
2. Remove the Foot Plates and brushes from the
unit.
3. Brushes and Foot Plates can be washed,
individually, in a COP tank, or wash machine.
4. The frame can be washed down by convenonal
means.
Operaon
The following maintenance procedures are
recommended for normal use. Units which see a
high amount of daily use should be inspected more
frequently as necessary.
Weekly:
• Inspect brushes for damage or wear.
• Check for missing or deformed bristles.
• Inspect plumbing/water lines for damage
• Ensure solid mounng to oor.
Monthly:
• Check all fasteners to ensure they are ght.
• Ensure warning labels and decals are present
and in good condion.
• Inspect valve for damage
Quarterly:
• Inspect structure for cracked welds or bent
components.
Maintenance

BLX-200W Manual Page 8 of 9 Updated: 02/11/21
USER MANUAL: BLX-200W
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Appendix A - Parts Callout
Part No. Descripon
F1036 BOLT HHC 5/16-18 X 3/4 SS
F1052 NUT NYLOCK 5/16-18 SS
F1151 WASHER 37/64 X 1-1/16 X 1/16 SS
F1152 BOLT HHC 5/16-18 X 2 SS
M1262 BRUSH FIXED 10-1/2 X 3
M1388 BRUSH BOX WLDMNT
M1392 BRUSH CLIP
M1393 FIXED SIDE BRUSH
M1395 FOOT PLATE BLX-200
M1396 FRONT PLATE BLX MANUAL
M1397 HANDRAIL BLX-200
M1398 REAR PLATE BLX-200
M1399 SPRAY BAR BLX MANUAL
M1407 SPACER BLX-200
P1047 VENTURI INJECTOR 3/8 SS
P1100 PIPE HEX NIPPLE 3/8 SS
P1102 PIPE NIPPLE 1/4 CLOSE SS
Part No. Descripon
P1108 PIPE CAP 1/4" SS
P1196 PIPE COUPLER 1/4"
P1211 QUICK FIT 1/4 NPT X 3/8 TUBE
P1214 QUICK FIT 3/8" T JOINT POLYPRO
P1219 QUICK FIT 3/8 NPT X 3/8 TUBE
P1221 QUICK FIT ELBOW 1/4" NPT x 3/8" TUBE
P1248 LABEL SLIP HAZARD
P1291 QUICK FIT Y 3/8"
P1302 PIPE NIPPLE 1/4 X 3 SS
P1338 METERING TIP, LOW FLOW 100- 15KU
P1355 VALVE PUSHBUTTON SS
P1358 PIPE BUSHING 1/2 X 3/8 SS
P1398 PRESSURE REGULATOR WATER 1/2" SS
P1599 METERING TIP, CAPILLARY TUBE
Venturi Kit:

BLX-200W Manual Page 9 of 9 Updated: 02/11/21
USER MANUAL: BLX-200W
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
GeneralInstallaonOperaonAppendix
Appendix B - Dimensions