ADTRAN QSFP28 100G SR4 User manual

Q
uic
k
Start
DESCRIPTION
QSFP28 SR4 transceivers are designed for use in 100 Gbps
(4 x 25 Gbps) optical links over multimode fiber. The QSFP28
SR4 integrates a four channel VCSEL array on the transmit and a
four channel PIN photodiode array on the receive. Each channel
can operate at 25.78 Gbps up to 100 m over OM4 Multi-mode
fiber. They are compliant with the QSFP28 MSA, IEEE P802.3bm
100GBASE- SR4.
INSTALLATION
To install the QSFP28 SR4 into an appropriate module, complete
the following steps:
1. Inspect the QSFP28 SR4. If damaged, file a claim with the
carrier and then contact ADTRAN Customer Support.
2. Do not remove the protective end cap from the QSFP until
you are ready to connect the fiber optic cable.
3. Insert the QSFP28 SR4 into the QSFP cage on the module.
Ensure the manufacturer’s label on the QSFP is facing
upward for correct installation.
4. Slide the QSFP28 SR4 all the way into the receptacle until
there is an audible “click.”
f
CAUTION!
Due to compliance certification requirements, use only QSFPs
supplied by ADTRAN. ADTRAN cannot certify system integrity
with other QSFPs.
wNOTICE
The latch on the QSFP is used to remove the QSFP from the
cage on the circuit card.
OPERATIONAL SPECIFICATIONS
General
■Module type: QSFP28
■Fiber/Copper: Fiber
♦Multi Mode
♦Single-fiber
♦Direction: BIDI
■Lanes/Channels: 4 Transmit and 4 Receive
■Signal Data Rate: 25.78 Gbps
■Optical Connector: MPO Connector
■Applications: 100 GBASE-SR4 Ethernet
■Distance: 0.1 km over OM4 Fiber
■Digital Diagnostic Monitoring: SFF8636 Compliant
Optical
Transmitter
■LaserDiodeType:VCSEL Array(4channels)
■Tx Central Wavelength: 850 nm
■Tx Power: –8.4 dBm to +2.4 dBm
■TxOutputOpticalPower:–5.0dBmto+2.4dBm ateachlane
■TxSpectralWidth:0.65 nm Max(RMS)
■Extinction Ratio: 2 dB min
■OpticalRisetime(tr):40ps (20%- 80%)
■Optical Fall time (tf) :40 ps (20% - 80%)
Receiver
■Rx Type: PIN Array
■Rx Central Wavelength: 850 nm
■Rx Power: +2.4 dBm to –7.2 dBm
■Receive Over load: +2.4 dBm at each lane
■ReceiveSensitivity:–7.2dBm ateachlane
Environmental
■Controlled Protected Environment (Inside)
♦Operational temperature range: –5°C to +50°C
♦Storage temperature range: –40°C to +85 °C
♦Relative humidity 5 to 85%
ADTRAN Pluggable Optics
QSFP
QSFP28 100G SR4
October 2018
61445510F1C-13B
P/N:1445510F1C

2 61445510F1C-13B
gNOTE
■This product is designed to be deployed in GR-3108-CORE
environmental class 1.
■This product is NRTL Listed to the applicable UL Standards.
The product is designed to meet the applicable requirements
of Telcordia GR-63-CORE and GR-1089-CORE.
■This product has also been evaluated to international safety
standards EN 60950-1, AS/NZS 60950.1, and IEC 60950-1.
This product meets the requirements for CE marking under the
EMC Directive and Low Voltage Directive. Standards used to
demonstrate Compliance are EN 300 386 and EN 60950.
■This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
■Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.
■This product is designed to meet the following environmental
classes:
♦ETSI EN 300 019-2-1 “Classification of environmental condi-
tions; Storage Class” 1.2
♦ETSI EN 300 019-2-2 “Classification of environmental condi-
tions, Transportation”, Class 2.3
♦ETSI EN 300 019-2-3 “Classification of environmental condi-
tions, Stationary use at weather protected locations”, Class
3.1E
■This product is designed to function without degradation during
exposure to all test severities per Class 3.3 of ETSI EN 300
019-2-3.
■This product meets EU RoHS Directive. Refer to
www.adtran.com for further information on RoHS/WEEE.
SAFETY AND REGULATORY
ENGLISH
fWARNING!
Read all warnings and cautions before installing or servicing this
equipment.
CCAUTION!
■This product contains or uses a Class 1 Laser module that
complies with FDA 21 CFR 1040.10, 1040.11 and IEC 60825-
1. For continued compliance with the above standards, only
approved Class 1 laser modules from an ADTRAN approved
vendor list (located on the ADTRAN website) should be
installed in this product. ADTRAN cannot certify system
integrity with other laser modules.
f
CAUTION!
■Electrostatic Discharge (ESD) can damage electronic
modules. When handling modules, wear an antistatic
discharge wrist strap to prevent damage to electronic
components. Place modules in antistatic packing material
when transporting or storing. When working on modules,
always place them on an approved antistatic mat that is
electrically grounded.
■This product meets or exceeds all the applicable requirements
of NEBS, Telcordia GR-63-CORE, and GR-1089-CORE. This
product is intended for deployment in Central Office type
facilities, EEEs, EECs, and locations where the NEC applies
(for example, Customer Premises.
■This system is designed and intended for installation as part of
a Common Bonding Network (CBN). This system is not
designed nor intended for installation as part of an Isolated
Bonding Network (IBN).
■This product does not have an internal DC connection
between battery return and frame ground. This product can be
installed in a DC-I (isolated) or DC-C (common) configuration.
■The chassis frame ground terminal must be connected to an
earth ground to ensure that the exposed metal (i.e., front
panels, SFP/XFP modules) on the product is properly
grounded by way of the backplane connector.

61445510F1C-13B 3
FRANÇAIS
fAVERTISSMENT!
Lisez tous les avertissements et mises en garde avant l’instal-
lation de cet équipement ou la réalisation de toute opération de
maintenance.
C
ATTENTION!
■Ce produit contient ou utilise un module Laser de classe 1 qui
est conforme avec la FDA 21 CFR 1040.10, 1040.11 et IEC
60825-1. Pour le maintien de la conformité avec les normes ci-
dessus, seulement approuvé classe 1 modules laser d'un
ADTRAN approuvés liste des fournisseurs (situé sur le site
ADTRAN) doit être installé dans ce produit. ADTRAN ne peut
certifier l'intégrité du système avec d'autres modules laser.
fATTENTION!
■L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des modules,
portez un bracelet de décharge antistatique pour éviter
d'endommager les composants électroniques. Placez les
modules dans un emballage antistatique lors du transport ou
du stockage. Lorsque vous travaillez sur les modules, placez-
les toujours sur un tapis antistatique certifié muni d'un
branchement de mise à la terre.
■La borne de terre de châssis doit être connecté à une prise de
terre pour assurer que le métal exposé (tels que les panneaux
avant, des modules SFP / XFP) sur le produit est correctement
mis à la terre via le connecteur de fond de panier.
■Ce système est conçu et prévu pour une installation intégrée
à un réseau de masse maillé. Ce système n’est pas conçu ni
prévu pour une installation intégrée à un réseau de masse
isolé (IBN).
■Ce produit ne dispose pas d’une connexion c.c. interne entre
le courant de retour de la batterie et la masse du châssis. Ce
produit peut être installé en configuration c.c.-I (isolé) ou c.c.-
C (commun).
■Ce produit est conforme à la directive. Reportez-vous à
www.adtran.com pour de plus amples renseignements sur
RoHS/WEEE.
DEUTSCH
f
WARNUNG!
Lesen Sie sich alle Warn- und Sicherheitshinweise durch, bevor
Sie dieses Gerät installieren oder warten.
C
VORSICHT!
■DasProdukt enthält oder verwendet Klasse 1 Laser-Module,
die 60825-1 mit FDA 21 CFR 1040.10, 1040.11 und IEC
erfüllen. Damit die obigen Richtlinien auch in Zukunft
eingehalten werden können, dürfen ausschließlich Klasse 1
Lasermodule von einem von ADTRAN zugelassenen Anbieter
in dem Produkt installiert werden (siehe Website von
ADTRAN). ADTRAN garantiert nicht für die Systemintegrität
bei anderen Lasermodulen
f
VORSICHT!
■Elektrostatische Entladung (ESD) können elektronische
Baugruppen beschädigt werden. Beim Umgang mit Modulen ,
tragen Sie eine Antistatikarmband, um Schäden an
elektronischen Bauteilen zu verhindern. Ort -Module in
antistatische Verpackung, beim Transport oder Lagerung. Bei
Arbeiten an Modulen immer legen Sie sie auf einer
zugelassenen antistatische Unterlage, die elektrisch geerdet
ist.
■Der Fahrgestellrahmen Erdanschluß muß zu einer Erde
verbunden werden, um sicherzustellen, dass das freiliegende
Metall (dh Frontplatten, SFP / XFP-Module) auf dem Produkt
richtig über den Backplane-Anschluss geerdet ist.
■Das System ist entwickelt und vorgesehen für die Installation
als Teil einer gemeinsamen Potentialausgleichsanlage. Das
System ist nicht zur Installation als Teil einer isolierten
Potentialausgleichsanlage vorgesehen
■Dieses Produkt hat keinen internen Gleichstromanschluss
zwischen Batterierücknahme und Gehäusemasse.
Dieses Produkt kann in einer DC-I (isoliert) oder DC-C
(emeinsam) Konfiguration installiert werden.
■Dieses Produkt erfüllt die EU RoHS Richtlinie. Bitte besuchen
Sie www.adtran.com für ausführlichere Informationen zu
RoHS/WEEE.

CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
©2018 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61445510F1C-13B*
Documentation for ADTRAN Network Solutions products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following online documents and resources provide additional information for this product:
ADTRAN Pluggable Optics Compatibility Matrix (online tool, go to: http://www.adtran.com/
pluggableoptics)