Clear One collaborate pro 900 User manual

COLLABORATE®Pro 900
Quick-Start Guide

COLLABORATE PRO 900
2
COMPONENTS INCLUDED
COLLABORATE Pro 900
COLLABORATE Pro
codec with power supply,
COLLABORATE Remote
control with dongle, and
HDMI cable.
910-2100-001
UNITE 100 PTZ camera,
power supply, DVI-I to
HDMI cable and RS232
Serial Control cable.
CONVERGE Pro 840T
Mixer, Beamforming
Microphone Array,
CONVERGE USB, cables
and power supplies.
Note: The Beamforming
Microphone Array
mounting kit must be
ordered separately.

QUICK-START GUIDE
3
MAKING THE CONNECTIONS
Connect the Beamforming Microphone Array to the CONVERGE Pro
840T, then connect the CONVERGE Pro 840T to the CONVERGE USB.
Connect the CONVERGE USB, UNITE 100 camera, Ethernet, and
monitor(s) to the COLLABORATE Pro codec as shown.
NOTE: Audio output and power connections not shown.
Ethernet Connection
CONVERGE Pro 840T
1080p HDMI Camera Video
USB Audio Transmit and Receive
CONVERGE USB
E-bus
HDMI
Output
Display Port
Output
UNITE
Camera
Camera Serial Control
E-bus From LINK Out
Beamforming Microphone
Array
CONVERGEP RO 840T
1 2 3 4

COLLABORATE PRO 900
4
CONNECTING THE REMOTE CONTROL DONGLE
The Remote Control includes a dongle that plugs into the FRONT USB
port on the codec.

QUICK-START GUIDE
5
CONFIGURING AUDIO INPUT AND OUTPUT
Loud Speakers
Amplifier
USB
Audio
Transmit and Receive
E-bus
LINK
Out
E-bus
LINK
In
CONVERGE USB
CONVERGE Pro Unit
E-bus
LINK
In
E-bus LINK Out
PoE (Power over Ethernet)
Beamforming Microphone
Array
COLLABORATE Pro Codec
NOTE: Power connections not shown.
CONVERGE PRO 840T
1 2 3 4

COLLABORATE PRO 900
6
CONFIGURING DISPLAY SETTINGS
After all peripherals are connected to the unit, turn the unit on.
Once COLLABORATE Pro is loaded – you will see your local camera
video on your screen.
Using the remote control, navigate to the display settings:
Settings > System > Display
According to your monitor capabilities, set to the maximum supported
resolution. If 2 monitors are connected to the unit, the display mode is
automatically changed to dual mode and you can set both monitors’
resolutions.

QUICK-START GUIDE
7
CONFIGURING AUDIO SETTINGS
The COLLABORATE Pro audio input and output is Converge Pro.
Verify this in COLLABORATE Settings > System > Audio

COLLABORATE PRO 900
8
CONFIGURING NETWORK SETTINGS
Using your remote control, navigate into the network settings:
Settings > Advanced > IP
Clearone.com
The COLLABORATE Pro obtains its IP automatically by default from the
DHCP server.
Uncheck the DHCP checkbox in order to manually configure network
settings.

QUICK-START GUIDE
9
CLEARONE CONTACTS
Europe & Oceana
Tel: [phone]
e-mail: [email protected]
Asia Pacific
Tel: [phone]
e-mail: [email protected]
HEADQUARTERS:
Salt Lake City, UT USA
5225 Wiley Post Way
Suite 500
Salt Lake City, UT 84116
Sales: 800-707-6694
Toll Free: 800.945.7730
Fax: [phone]
e-mail: [email protected]
TechSales
Tel: [phone]
e-mail: [email protected]
Technical Support
Tel: [phone]
e-mail: [email protected]
Latin America
Tel: [phone]
e-mail: [email protected]
Middle East
Tel: [phone]
e-mail: [email protected]
© 2015 ClearOne, Inc. All rights reserved.
Information in this document is subject to change without notice. QSG-0025-001 Revision 1.1, September, 2015