Clear One Versa UCS2100 User manual

User Manual
Versa™ UCS2100 Collaboration Switcher Kit
UCS2100T
UCS2100R

Versa™ UCS2100 Collaboration Switcher Kit User Manual
1DOC-0570-001v1.0 April 2023
ClearOne®Contacts
Headquarters Headquarters
5225 Wiley Post Way Suite 500 Tel: [phone]
Salt Lake City, UT 84116
Sales Technical Support
Tel: [phone] Tel: [phone]
sales @ clearone.com audiotechsupport @ clearone.com
Notices
© 2023 ClearOne, Inc. All rights reserved.
Information in this document is subject to change without notice.
Document: DOC-0570-001v1.0, April 2023
Preface
Read this user manual carefully before using the product. Pictures shown in this manual are for reference only. Different
models and specifications are subject to real product.
This manual is only for operation instruction, please contact the local distributor for maintenance assistance. The
functions described in this version were updated by November 2022. In the constant effort to improve the product, we
reserve the right to make functions or parameters changes without notice or obligation. Please refer to the dealers for the
latest details.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. It has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a commercial installation.
Operation of this equipment in a residential area is likely to cause interference, in which case the user at their own
expense will be required to take whatever measures may be necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void the user’s authority to operate the
equipment.

Versa™ UCS2100 Collaboration Switcher Kit User Manual
2DOC-0570-001v1.0 April 2023
SAFETY PRECAUTIONS
To ensure the best from the product, please read all instructions carefully before using the device. Save this manual for
further reference.
• Unpack the equipment carefully and save the original box and packing material for possible future shipment.
• Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• Do not dismantle the housing or modify the module. It may result in electrical shock or burn.
• Using supplies or parts not meeting the products’ specifications may cause damage, deterioration or malfunction.
• Refer all servicing to qualified service personnel.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Do not put any heavy items on the extension cable in case of extrusion.
• Do not remove the housing of the device as opening or removing housing may expose you to dangerous voltage or
other hazards.
• Install the device in a place with fine ventilation to avoid damage caused by overheat.
• Keep the module away from liquids.
• Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills
on to the housing, unplug the module immediately.
• Do not twist or pull by force ends of the cable. It can cause malfunction.
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
• Unplug the power cord when left unused for a long period of time
• Information on disposal for scrapped devices: do not burn or mix with general household waste, please treat them as
normal electrical wastes.

Versa™ UCS2100 Collaboration Switcher Kit User Manual
3DOC-0570-001v1.0 April 2023
anchor
Contents
1. Product Introduction .........................................................................5
1.1 Features........................................................................................5
1.2 Packing List ..................................................................................5
1.3 Warranty information....................................................................5
2. Specification......................................................................................6
3. Panel Description..............................................................................8
3.1 Transmitter....................................................................................8
Front Panel .......................................................................................8
Rear Panel ........................................................................................9
3.2 Receiver......................................................................................10
Front Panel .....................................................................................10
Rear Panel ......................................................................................10
4. EDID Management..........................................................................11
5. GUI Control .....................................................................................12
5.1 Video Tab....................................................................................13
5.2 Configuration Tab.......................................................................13
5.2.1 EDID......................................................................................13
5.2.2 Auto Downscale....................................................................14
5.2.3 HDCP ....................................................................................14
5.2.4 Tags.......................................................................................15
5.2.5 Device Control ......................................................................15
5.3 CEC Tab .....................................................................................16
5.3.1 Input ......................................................................................16

Versa™ UCS2100 Collaboration Switcher Kit User Manual
4DOC-0570-001v1.0 April 2023
5.3.2 Output ...................................................................................16
5.3.3 User-defined..........................................................................17
5.4 RS-232 Tab...............................................................................18
5.5 Network Tab .............................................................................18
5.6 Access Tab...............................................................................19
6. RS-232 Control ...............................................................................22
6.1 RS-232 Command......................................................................22
6.1.1 System Control .....................................................................22
6.1.2 Source Control......................................................................26
7. System Connection ........................................................................29
8. Panel Drawing.................................................................................31

Versa™ UCS2100 Collaboration Switcher Kit
5DOC-0570-001v1.0
User Manual
Back to Table of Contents April 2023
1. Product Introduction
Versa UCS2100 Collaboration Switcher Kit is an 18 GBPS switcher kit. It supports up to 4K/60/4:4:4, HDR 10 and Dolby
Vision, HDCP 2.2. It also supports uncompressed transmission of 18 GBPS signals with a distance of up to 100 m. At
the same time, it can be connected to KVM equipment, which is very suitable for equipment connection and signal
transmission in conference rooms. The switcher kit also supports RS-232 and CEC control and bidirectional 48 V Power-
Over-Cable
1.1 Features
• Automatically detects HDMI and USB-C sources, such as dedicated in-room PC and BYOM laptop, and offers the
flexibility for users to access the same set of in-room AV peripherals, such as cameras and audio devices.
• Supports up to 4K 60 Hz 4:4:4 resolution, HDCP 2.2, HDR 10 and Dolby Vision.
• Bi-Directional HDBaseT 3.0, allows the remote peripherals to be placed at a distance of up to 100 meters and
provides 48 V PoE.
• USB-C input supports up to 60 W charging.
• Ethernet ports provide network passthrough between the transmitter and receiver unit.
• The transmitter unit provides simultaneous 1 x HDMI output and 1 x HDBaseT output.
• Supports automatic source detection & switching.
• Controllable via RS-232, TCP/IP, or front panel buttons.
• Multiple USB ports on both the transmitter and receiver for connecting a camera, audio device, mouse, and
keyboard.
1.3 Warranty information
We provide 2 year limited warranty starting from date of purchase.
Note: Please contact your distributor immediately if any damage or defect in the components is found.
1.2 Packing List
1 x Versa UCS2100T
1 x Versa UCS2100R
1 x 24 VDC 5 A power adapter
1 x QR-code card for the Quick Start Guide (QSG)
5 x 3-pin terminal block
2 x 5-pin terminal block
1 x 3-pin to DB9 RS-232 cable
4 x hangers
6 x screws
8 x foot pads
1 x 1mtr USB-C to C 10Gbps cable
www.clearone.com

Versa™ UCS2100 Collaboration Switcher Kit
6DOC-0570-001v1.0
User Manual
Back to Table of Contents April 2023
Item No. Function Description
Transmitter Receiver
Video
1Video Input (1) HDMI IN, (1) USB-C IN (1) HDBT IN
2Input Resolution HDMI: Up to 4K @ 60 Hz 4:4:4
HDR 10, Dolby Vision
Up to 4K @ 60 Hz 4:2:0
USB-C: Up to 4K @ 60 Hz 4:4:4
3Video Output (1) HDMI OUT (1) HDBT OUT (1) HDMI
4Video Output
Connector
(2) HDMI Type-A Receptacles (1) HDMI Type-A
Receptacles
5Output Resolution HDMI: Up to 4K @ 60 Hz 4:4:4
HDR 10, Dolby Vision
Up to 4K @ 60 Hz 4:4:4
HDR 10, Dolby Vision
HDBT: Up to 4K @ 60 Hz 4:2:0
6HDMI Standard Up to HDMI 2.0 b Up to HDMI 2.0 b
7HDCP Version Up to HDCP 2.2 Up to HDCP 2.2
Audio
8HDMI Embedded Audio
Format
LPCM 7.1 audio, Dolby Atmos®, Dolby® TrueHD, Dolby
Digital® Plus, DTS:X™, and DTS-HD® Master Audio™ pass-
through.
9Audio Output
Connector
(1) 5-pin terminal block (1) 5-pin terminal block
10 Frequency Response 20 Hz – 20 KHz, ±3 dB
11 Max Output Level 0.88 Vrms ± 0.5 dB. 2 V = 16 dB headroom above -10 dBV
(316 mV) nominal consumer line level signal
SPDIF: ± 0.05 dBFS
12 THD+N < 0.05% (-80 dB), 20 Hz – 20 kHz bandwidth, 1 kHz sine at
0 dBFS level (or max level)
13 SNR > 80 dB, 20 Hz – 20 kHz bandwidth
SPDIF: > 90 dB, 20 Hz – 20 kHz bandwidth
14 Crosstalk Isolation < -80 dB, 10 kHz sine at 0 dBFS level (or max level before
clipping)
15 L-R Level Deviation < 0.3 dB, 1 kHz sine at 0 dBFS level (or max level before
clipping)
16 Output Load Capability 1 k ohm and higher
2. Specification

Versa™ UCS2100 Collaboration Switcher Kit
7DOC-0570-001v1.0
User Manual
Back to Table of Contents April 2023
Item No. Function Description
Transmitter Receiver
Control
General
17 Operation Temperature -5 – +55 °C
18 Storage Temperature -25 – +70 °C
19 Relative Humidity 10% – 90%
20 External Power Supply Input: AC 100 – 240 V, 50/60 Hz; Output: 24 VDC 5 A.
21 Power Consumption 76.5 W (Max)
22 USB-C Power Charging 60 W (Max)
23 Dimension (W*H*D) 265 W x 32 H x 150 D mm 173 W x 24.5 H x 95 D mm
24 Net Weight 1020 g 410 g

Versa™ UCS2100 Collaboration Switcher Kit
8DOC-0570-001v1.0
User Manual
Back to Table of Contents April 2023
3. Panel Description
3.1 Transmitter
Front Panel
1 2 3 4 5 6 7 8
No.Name Description
1 Power LED 1 x green indicator light, the light is on when power is present.
2 SELECT • 1 x white non-backlit button, 3 x blue indicator lights
• Click the button to select the input source (HDMI or USB-C), press and
hold for 3 seconds to enter or exit automatic switching mode.
3 DISPLAY • 1 x white non-backlit button, 2 x blue indicator lights
• Press the button to send the DISPLAY ON/OFF CEC and RS-232
commands to the displays connected to the transmitter (TX) unit and the
receiver (RX) unit.
• When the CEC command control includes TX, the front panel button
indicator will flash three times
• When CEC only controls RX, the CEC button indicator light switches
synchronously
• When the CEC command controls TX/RX at the same time, the buttons on
the front panel switch synchronously and the indicator light flashes three
times.
4 BLACK
SCREEN
• 1 x white non-luminous button, 2 x blue indicator lights
• Press the button to enter or exit the output black screen
5 EDID 1 x 4-pin DIP switch for EDID management
6 DEVICES 2 x USB-A 3.0, connect keyboard, mouse, audio conferencing system, network
adapter, printer, and other equipment
7 ETHERNET 1 x RJ45, used for network passthrough transmission to the receiver unit
8 FW 1 x Micro-USB, 1 x Micro USB, for future use

Versa™ UCS2100 Collaboration Switcher Kit
9DOC-0570-001v1.0
User Manual
Back to Table of Contents April 2023
Rear Panel
1 2 3 4 5 6 7 8 9 10 11
No.Name Description
1 USB-C • 1 x USB-C 3.0 input, supports external 60 W charging, connect to the host
laptop.
• Video is supported when connected to the host computer’s USB-C port. If
connected to the host computer’s USB Type-A port, video is not supported.
2 HOST • 1 x USB-B 3.0, connect to HOST devices such as laptops, connect to the
host computer.
• Video is not supported through this USB port. You must connect the
computer to the HDMI Input for video when using this USB port.
• The HDMI Input is used in combination with the USB HOST port.
3 HDMI IN • 1 x HDMI input, connect to HOST devices such as laptops, connect to the
host computer
• The HDMI Input is used in combination with the USB HOST port.
4 HDMI OUT 1 x HDMI Output, contains video from either the HDMI Input or USB-C Input,
whichever is selected.
5 HDBT 1 x HDBT output, the green light is always on when the signal is with HDCP,
flashes when the input signal is without HDCP, the yellow light is always on
after the TX and RX are connected.
6 AUDIO 1 x 5-pin balanced audio output, HDMI de-embedding, contains the audio that
is being sent to the HDMI Output.
7 Control GR1: Corresponds to the USB-C Input
GR2: Corresponds to the HOST/HDMI Input
SM: Switch to the corresponding source
BO: Print a black screen to all outputs.
8 RS-232 LOCAL: Connect local devices for bidirectional communication with the
transmitter
PASS: Bidirectional passthrough transmission with the receiver’s RS-232 port

Versa™ UCS2100 Collaboration Switcher Kit
10 DOC-0570-001v1.0
User Manual
Back to Table of Contents April 2023
No.Name Description
9 Button For future use
10 TCP/IP 1 x RJ45, TCP/IP control, connect to the local network for configuration via the
web gui and for control using text commands.
11 DC 24 V Connect the provided 24 VDC 5 A power adapter to either the transmitter’s or
receiver’s power input. If the power adapter is connected to the transmitter,
then the receiver will be powered over the CAT 6 cable.

Versa™ UCS2100 Collaboration Switcher Kit
11 DOC-0570-001v1.0
User Manual
Back to Table of Contents April 2023
3.2 Receiver
Front Panel
1 2
No.Name Description
1 OUTPUT • 1 x HDMI output
• 1 x 5-pin balanced audio output, provides de-embedded audio from the
HDMI output
2 DEVICES 3 x USB-A 2.0, 1 x USB-C, connect keyboard, mouse, audio conferencing
system, network adapter, printer, and other equipmen

Versa™ UCS2100 Collaboration Switcher Kit
12 DOC-0570-001v1.0
User Manual
Back to Table of Contents April 2023
Rear Panel
1 2 3 4
No.Name Description
1 ETHERNET 1 x HDMI output;
2 HDBT IN 1 x RJ45 interface, the green light is always on when the signal is with HDCP,
flashes when the input signal is without HDCP, the yellow light is always on
after the TX and RX are connected.
3 RS-232 1 x 3-pin phoenix head, Bidirectional passthrough with the transmitter’s RS-232
port
4 Power LED 1 x green indicator light, the light is on when power is present.
5 DC 24 V Connect the provided 24 VDC 5 A power adapter to either the transmitter’s or
receiver’s power input. If the power adapter is connected to the receiver, then
the transmitter will be powered over the CAT 6 cable.

Versa™ UCS2100 Collaboration Switcher Kit
13 DOC-0570-001v1.0
User Manual
Back to Table of Contents April 2023
4. EDID Management
To ensure the attached display gets the best picture and audio results, the EDID (Extended Display Identification Data)
DIP switch can be set according to the table below.
DIP Switch Description
0000 Learn the display EDID in the default mode: read the EDID of the TX HDMI output
and RX HDMI output, and output the EDID with the lower resolution of the two, if
you can’t learn it, then use the built-in 1920 x 1080 @ 60 8 bit Stereo
0001 1920 x 1080 @ 60 8 bit High Definition Audio
0010 3840 x 2160 @ 60 Hz Deep Color Stereo Audio
0011 3840 x 2160 @ 30 Hz 8bit Stereo Audio
0100 3840 x 2160 @ 30 Hz Deep Color High Definition Audio
0101 3840 x 2160 @ 60 Hz 4:2:0 Deep Color Stereo Audio
0110 3840 x 2160 @ 60 Hz Deep Color High Definition Audio
0111 3840 x 2160 @ 60 Hz Deep Color HDR LPCM 6 CH
1011 Custom EDID1
1100 Custom EDID2
1101 Custom EDID3
1110 Custom EDID4
1111 EDID management

Versa™ UCS2100 Collaboration Switcher Kit
14 DOC-0570-001v1.0
User Manual
Back to Table of Contents April 2023
5. GUI Control
The Versa UCS2100 collaboration switcher kit can be controlled via TCP/IP. The default IP settings are:
IP Address:192.168.0.178
Subnet Mask:255.255.255.0
Gateway:192.168.0.1
Please type the IP Address on the control PC in the internet browser, and it will enter the below log-in webpage
Username: admin
Password: admin
Please type the username and the password, and then click LOGIN.

Versa™ UCS2100 Collaboration Switcher Kit
15 DOC-0570-001v1.0
User Manual
Back to Table of Contents April 2023
5.1 Video Tab
• Choose the HDMI, USB-C or Auto source according to actual usage.
5.2 Configuration Tab
5.2.1 Video Tab
• Choose the desired EDID format or define the appropriate EDID format.

Versa™ UCS2100 Collaboration Switcher Kit
16 DOC-0570-001v1.0
User Manual
Back to Table of Contents April 2023
5.2.2 Auto Downscale
• Enable or disable the auto Downscale in TX or RX output
5.2.3 HDCP
• Choose whether HDCP follows the source or the display. The HDCP for transmitter unit and the receiver unit can be
configured individually.

Versa™ UCS2100 Collaboration Switcher Kit
17 DOC-0570-001v1.0
User Manual
Back to Table of Contents April 2023
5.2.4 Tags
• The names of the input and output channels can be customized. Type in new labels and click Confirm to save the
changes.
5.2.5 Device Control
• Choose and enter the device control, then click confirm to change the device control.

Versa™ UCS2100 Collaboration Switcher Kit
18 DOC-0570-001v1.0
User Manual
Back to Table of Contents April 2023
5.3 CEC Tab
5.3.1 Input
• Click on any button to send the associated CEC command to the device attached to the HDMI input. CEC is an
acronym for Consumer Electronics Control and provides control of devices through the HDMI cable. Commands
can also be initiated through RS-232 or TCP/IP.
5.3.2 Output
• Click on any button to send the associated CEC command to the display attached to the HDMI Output. CEC is an
acronym for Consumer Electronics Control and provides control of devices through the HDMI cable. Commands
can also be initiated through RS-232 or TCP/IP.

Versa™ UCS2100 Collaboration Switcher Kit
19 DOC-0570-001v1.0
User Manual
Back to Table of Contents April 2023
5.3.3 User-Defined
• Define the Trigger of input and output.