Introduction
This product supports IEEE802.3U IEEE802.3z 1000Base-
Tx/Fx protocol and IEEE802.3at/af PoE+ PSE applications.
The internal AC/DC power supply and PSE controller
can output up to 30Watts (DC52V/600mA) or 25Watts
(DC48V/540mA) or 15.4Watts (DC48V/350mA) power into
a CAT5 twisted-pair cable.
The following guide is for the user’s reference.
Package Contents
The following items are included:
PoE+ (PSE) media converter 1 set
Power cable 1 each
User manual 1 each
Please contact the seller immediately if any of the above
are missing or damaged
Installation
1. Interface
RJ-45 Interface
The transmission media uses CAT5 twisted-pair with a
maximum length of up to 100 meters (330 feet).
Fiber Interface
Fiber interface accepts duplex mode type, including two
interfaces, send (TX) and receive (RX). When the two sets
of optical transceiver are interfaced or connected to switch
with fiber interface, the fiber is in cross connection, i.e.
“TX-RX”, “RX-TX” (direct connection for single optical fiber
transceiver module).
Power Supply Interface
The AC power supply is connected to AC-input jack of the
media converter through the attached AC power cable.
2. Connection
Connect a network device (network card, hub or switch,
etc.) with an RJ-45 interface to the RJ-45 jack of media
converter via twisted-pair.
This switch accepts standard SFP modules, which should
be selected to match the ber type in use (single mode or
multimode). Insert SFP module into pictured “Fiber” port
(below). Connect a matching single mode or multimode
optical ber to the ber interface of the optical transceiver
module.
Connect AC power cable. LED indicators will indicate
connection success. (See the table below for LED indicator
light identication.)
LED Indicator Lights
PWR ON when the power supply is turned on
Link/Act
(FX)
Bright when optic ber cable is connected correctly but
data is not transmitting
Blinking when receiving data
Link/Act
(TP)
Bright when twisted pair is connected correctly but data
is not transmitting
Blinking when receiving data
FDX(TP)
ON when TP link is in full duplex mode
OFF when TP link is in half duplex mode
1000M
ON 1000M
OFF 100M or 10M
100M
ON 100M
OFF 1000M (1000M ON) or 10M (1000M OFF)
POE
ON when connected and PD load correct
OFF when no load or load problem
Blinking when load is abnormal
PWR/POE
ON when POE 48V power is stable
OFF when POE 48V power is decreasing or too low
DIP Switch Functions
NO. Function Status Specication
SW1-1 ENROM * OFF FX_reset disable
ON FX_reset enable
SW1-2 FX100M OFF FX 1000M (default)
ON FX 100M
SW1-3 POE
shutdown
OFF POE shutdown disable
ON POE shutdown enable
SW1-4 LFP OFF LFP Disable
ON LFP Enable
SW1-5 MODE1 OFF ALS disable
ON ALS enable
SW1-6 MODE0* OFF AI_POE disable
ON AI_POE enable
Note:
* FX Reset: if enabled, when FX link is down, power will shut
down for a few seconds and restart.
* AI_POE: if enabled, If there is no data input for two
minutes, Poe will restart.
Main Features
1. In conformity to IEEE802.3U IEEE802.3z
1000Base-Tx/Fx standard.
2. IEEE802.3 at/af PoE+ PSE compatible
3. Half duplex: back pressure ow control
Full duplex: IEEE802.3x ow control.
4. Automatic identication of MDI/MDI-X cross line.
5. Supports link fault pass through function.
