Cleerline SSF-SFP-RJ45-1G User manual

SSF-SFP-RJ45-1G / SSF-SFP-SFP-CON
Gigabit Fiber Media Converters
Manual
www.cleerlineber.com

Gigabit Fiber Media Converters
2
GIGABIT FIBER MEDIA CONVERTERS
Ordering Information
SSF-SFP-RJ45-1G Gigabit Media Converter 10/100/1000Base-Tx to
100/1000Base-X SFP slot, DIP sw cong., AC adapter included
SSF-SFP-SFP-CON multi-rate Media Converter SFP slot to SFP slot, DIP sw
cong., AC adapter included
Overview
These Gigabit Ethernet ber media converters provide high performance and
reduced size. Units have DIP switches for custom speed and ow settings for
strong networking exibility. Physical dimensions have been reduced for minimum
footprint and highest density attainable in 19” rack environment: 12 units/RU.
Reliability is highly ranked with an MTBF exceeding 65,000 hours.
Converters support IEEE802.3u IEEE802.3z 1000Base-TX/FX protocols. Package
includes AC adapter 100-240V to DC 5V and one User Manual.
Features
• 10/100/1000Base-T to 100/1000Base-X Conversion (or same rate transparent
for SSF-SFP-SFP-CON model)
• Auto-Negotiation and Auto MDI/MDIX (LFC-1001/1002-SFP)
• Forward 2048 bytes (Max.) packets in switch mode (copper & ber port in
different speed)
• Forward 9k bytes in converter mode (ber & copper port at the same speed)
• DIP switch settings for ber speed (100/1000M), LPF and Flow control
• Support for Q in Q double tagged frame transparent
• Support for IEEE 802.1Q Tag VLAN pass thru
• 100M to 2.5G transparent O-E-O repeater – both optical ports must have
same rate (model SSF-SFP-SFP-CON)
• Installs into high density 12 slot/1RU rack mountable chassis (with options of
redundant and AC or DC48 power supplies)

Gigabit Fiber Media Converters
3
DIP Switch Settings
MODEL SSF-SFP-SFP-CON
DIP Function Settings
SW 1 LFP OFF – Disabled ON – Enabled
SW 2 Forwarding Mode OFF/OFF
OFF/ON
Store & Forward
Cut Through
SW 3 (paired setting 2&3) ON/OFF
ON/ON
Smart Pass Through
Pass Through
SW 4 FX port 100M mode OFF – 1000M ON – 100M
LED Indicators (Markings Will Vary with Models)
FUNCTION
TP/LNK Off – No link; On – RJ45 link OK; Blinking – data trac present
SPD Off – 10M/100M; On – 1000M on RJ45 port
FX/LNK SFP1 SFP2 Off – No link; On – Fiber link OK; Blinking – data trac present
PWR Off – No power available; On – Power is present
Installation
1. Choose a at secure surface with room for proper ventilation.
2. Power up the unit using the included AC adapter. Observe PWR LED status
indicating proper power to the unit.
3. Connect RJ45 UTP port using Cat5e or better cable to another Ethernet
device. Make sure the TP LED indicates proper connectivity.
4. Insert a Gigabit or Fast Ethernet rated SFP transceiver into the SFP slot. Make
sure the ber transceiver used matches the ber type (MM or SM) and also
matches a similar optical transceiver at the other end of the ber. Inspect FX
LED for proper ber link status.
Troubleshooting
1. No TP/LNK light: verify proper UTP cabling/pinout.
2. No FX/LNK light: verify ber connectivity and ber type. Consider cleaning up
ber connectors and SFPs with appropriate tools. Make sure Tx and RX ports are
properly crossed between units. Make sure FX speed is properly set on DIP sw.
3. No PWR light: Use only the AC adapter included. Make sure AC power is available

Gigabit Fiber Media Converters
4
Technical Specications
Standards IEEE 802.3, 802.3u, 802.3z, 802.3ab
Connectors SFP slot, RJ45 UTP port, DC power plug
UTP port RJ45, Auto MDI/MDI-X, full duplex, 10M, 100M or
1000M modes
SFP slot Supports 100M or 1000M speed SFPs (up to 2.5G
for SSF-SFP-SFP-CON)
Power Adapter Adapter with AC 100-240V input, 0.5A
AC frequency: 50-60Hz, Output DC 5V/1A
Power Requirements DC 5-12V, 4W max. power consumption
Dimensions 90mm x 60mm x 20mm (SFP not included)
Mounting Wall or shelf (optional bracket needed)
Environmental Conditions
Operating Ambient Temperature: 0 to 50°C
Operating Humidity: Maximum 85%, Non-
condensing
Storage Temperature: -30 to 70°C
Storage Humidity: Maximum 95%, Non-condensing
Indoor rated operating device
MTBF 65,000 hours
Warning
1. Use only indoors in climate-controlled environment.
2. Avoid looking directly into bers or lasers while unit is powered.
3. Use only the AC adapter included with the unit (or with the LFC series chassis
available separately)
FCC and CE markings
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
This is a CE class B device, intended to be used in residential, commercial or
industrial applications.