Cleerline SSF-MICROV-250X User manual

SSF-MICROV-250X
Video Microscope
Instruction Manual
www.cleerlinefiber.com

1
SSF-MICROV-250X
WARNING
To avoid the risk of eye damage, never look directly into optical fibers or
light sources when active.
KIT CONTENTS
1 ea handheld probe with cable
1 ea LCD display screen
1 ea DC/AC power adapter
1 ea SSF-1CLCK-LC 1.25 mm One-Click Type Cleaner, LC
1 ea SSF-1CLCK-SC 2.5 mm One-Click Type Cleaner, SC
Adapter Tips
1 ea SC/ST/FC E2000 UPC connector adapter (male)
1 ea LC UPC connector adapter (male)
1 ea SC/ST/FC E2000 UPC bulkhead adapter (female)
1 ea LC UPC bulkhead adapter (female)
View instructions and video online at cleerlinefiber.com/resources.

2
SSF-MICROV-250X
INTRODUCTION
The SSF-MICROV-250X is a portable video microscope kit intended for
the verification of fiber optic terminations. Use the SSF-MICROV-250X
to inspect installed connectors, including those in patch panels or
inside hardware devices. The included handheld probe has adapter tips
for use with LC UPC and SC UPC connectors (male), as well as LC UPC
and SC UPC bulkheads (female). The bulkhead adapters (female) can
be used to access patch cables connected at the rear of bulkheads or
adapter plates.
Applications
• Patch panel inspection, including connectors installed on the front
and the back of patch panels
• Inspection of cable assemblies, including patch cables, pigtails, and
cable assemblies
Specifications
Type Description
Battery 3.7 V, 4500 mA 5V/1A rechargeable Li
Battery
Monitor 0.30 kg / 0.67 lbs
14.5 x 7.5 x 4 cm / 5.7 x 3.0 1.6 in
Operation/Storage
Temperature -20°C - +50°C / -30°C - + 60°C

3
SSF-MICROV-250X
PARTS
Handheld Probe
This probe utilizes an analog CCD, which outputs an NTSC or a PAL
signal. The signal is routed through a 4-pin connector that routes power
into the probe and video signal out of the probe. This unit is suitable for
use with the handheld LCD display.
Barrel Assembly
The barrel assembly houses the optics. LC, SC, ST, FC, E2000, MTRJ and
other customized PC or APC adapters are compatible.
Focus Control
The default magnification is 250x. When the endface image appears on
the display, adjust the focus control to sharpen the image.

4
SSF-MICROV-250X
PARTS
LCD Display
The display can be powered using the 110-240V DC/AC power unit or
with the included rechargeable lithium-ion battery. The DC/AC adapter
can power the display and charge the battery simultaneously.
This unit accepts video input from the kit’s PAL/NTSC formatted probe.

5
SSF-MICROV-250X
PARTS
Adapter Tips
Adapter Type Description
25-U-M SC/FC/ST/E2000 connector, UPC
125-U-M LC/MU connector, UPC
25-U-F SC/FC/ST/E2000 bulkhead, UPC
LC-U-F LC bulkhead, UPC

6
SSF-MICROV-250X
OPERATION
Adapter Tip Installation
Connecting the LCD Display
Select desired adapter tip. Screw adapter tip onto handheld probe
barrel. Do not over-tighten.
Step 1: Connect probe cable to the 4-pin connector at the top of the
display unit.
Note: Do not attempt to turn or unscrew the barrel assembly of the
handheld probe. This can damage the whole unit.
Step 2: Connect the AC power adapter/charger if necessary.
Step 3: Push On/Off button to activate display screen.
View instructions and video online at cleerlinefiber.com/resources.

7
SSF-MICROV-250X
OPERATION
Note: Do not touch cleaner tip.
End Cap Cover
End Cap
Extension Button
Indicator Window
One-Click Type Fiber Optic Cleaner
Connectors in Adapters (Bulkhead)
Remove end cap. Insert cleaner into connector. Push until the cleaner
clicks. Do not angle cleaner.
Connectors Not in Adapters
Open end cap cover. Do not remove entire end cap. Insert connector into
cleaner. Push until cleaner until the cleaner clicks. Do not angle cleaner.
Extending Nozzle
Depress black button on side of cleaner and pull nozzle to extend.
Indicator Window
White: Full
Red: Empty. Note: cleaner tip will appear black. Do not use when empty.

8
SSF-MICROV-250X
WARRANTY
We warrant this equipment against defects in material and workmanship
for a period of one year from the date of original shipment. We also
warrant that this equipment will meet applicable specifications under
normal use. During the warranty period, we will, at our sole discretion,
repair or replace for any defective product free of charge should the
equipment need to be repaired.
The warranty will become null and void if
• the equipment has been tampered with, repaired, or worked upon by
unauthorized individuals.
• the warranty label has been removed.
• product enclosure screws, other than those specified in this manual,
have been removed.
• the product enclosure has been opened, other than as explained in
this manual.
• the equipment serial number has been altered, erased, or removed.
• the equipment has been misused, neglected, or accidentally damaged