CLEVERSPA 10001 User manual

INSTRUCTION
MANUAL
Cord-connected inflatable hot tub
with built in blower, heater and
control device
ETL MODEL No. 10001 / 10002 / 10003 / 10004
CLEVERSPA ETL US IM_FINAL.indd 1CLEVERSPA ETL US IM_FINAL.indd 1 07/01/2020 16:1707/01/2020 16:17

IMPORTANT SAFETY INSTRUCTIONS - READ, FOLLOW AND SAVE ALL INSTRUCTIONS
FOR FUTURE REFERENCE - SEE PAGE 15 FOR A REPLACEMENT SAFETY SIGN
When installing and using this electrical equipment, there are basic safety precautions that
should always be followed, including the following:
• WARNING: Do not permit children to use this product unless they are closely supervised at all times.
• A wire connector is provided on this unit to connect a minimum, 6 AWG (13.3mm2) solid copper conductor
between this unit and any metal equipment, metal enclosures of electrical equipment, metal water pipe, or
conduit within 5 feet (1.5m) of the unit.
• DANGER: Risk of injury.
a) Replace damaged cord immediately.
b) Do not bury cord.
c) Connect to a grounded, grounding type receptacle only.
• WARNING: This product is provided with a ground-fault circuit-interrupter within the plug. The GFCI must be
tested before each use. With the product operating, When the product stops operating, this indicates that the
door is equipped with an electrical interlock. Next, push the test button on the GFCI and close the service door.
The product should not operate. Now open the service door, push the reset button on the GFCI and close the
service door. The product should now operate normally. When the product fails to operate in this manner, there
is a ground current flowing indicating the possibility of an electric shock. Disconnect the power until the fault
has been identified and corrected.
• DANGER: Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access by
children. To avoid accidents, ensure that children cannot use this hot tub unless they are supervised at all times.
• DANGER: Risk of Injury. The suction fittings in this hot tub are sized to match the specific water flow created
by the pump. Should the specific water flow created by the pump? Should the suction fittings or the pump?
Be sure that the flow rates are compatible. Never operate hot tub if the suction fittings are broken or missing.
Never replace a suction fitting with one rated less than the flow rate marked on the original suction fitting.
• DANGER: Risk of Electric Shock. Install at least 5 feet (1.5m) from all metal surfaces. As an alternative, a hot tub may
be installed within 5 feet of metal surfaces if each metal surface is permanently connected by a minimum, 6 AWG
(13.3mm2) solid copper conductor to the wire connector on the terminal box that is provided for this purpose.
• DANGER: Risk of Electric Shock. Do not permit any electric appliance, such as a light, telephone, radio, or
television, within 5 feet (1.5m) of a hot tub.
• WARNING: To reduce the risk of injury:
a) The water in a hot tub should never exceed 40°C (104°F). Water temperatures between 38°C (100°F) and
40°C (104°F) are considered safe for a healthy adult. We recommend never exceeding 38°C for young
children and when hot tub use exceeds 10 minutes.
b) Since excessive water temperatures have a high potential for causing fetal damage during the early months
pregnant women should limit hot tub water temperatures to 38°C (100°F).
c) Before entering a hot tub, the user should measure the water temperature with an accurate thermometer
since the tolerance of water temperature-regulating devices varies.
d) The use of alcohol, drugs, or medication before or during hot tub use may lead to unconsciousness with
the possibility of drowning.
e) Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory
system problems, or diabetes should consult a physician before using a hot tub.
Safety Instructions 02 - 03
CleverSpa® Parts Checklist 04
Indoor & Outdoor CleverSpa® Installation 06
Setting up your CleverSpa® 07 - 08
Operating your CleverSpa® 10
Maintenance & Repair of your CleverSpa® 11
Cleaning & Storing away your CleverSpa® 12
Troubleshooting 13
Returns 14
Warranty 15
02
CONTENTS
CLEVERSPA ETL US IM_FINAL.indd 2CLEVERSPA ETL US IM_FINAL.indd 2 07/01/2020 16:1707/01/2020 16:17

f) Consult your doctor before use as some medication may induce drowsiness while other medication may
affect heart rate, blood pressure, and circulation.
g) To accurately check the water temperature we recommend the use of a calibrated digital thermometer
or mercury thermometer, ensuring this matches with the spa control panel (see page 10 regarding how
to operate your hot tub).
• Hypothermia occurs when the internal temperature of the body reaches a level several degrees above
the normal body temperature of 37°C (98.6°F). The symptoms of hypothermia include an increase in
the internal temperature of the body, dizziness, lethargy, drowsiness and fainting.
The effects of hypothermia include failure to perceive heat, a failure to recognise the need to exit the
CleverSpa®, an unawareness of impending hazards, fetal damage in pregnant women, a physical inability
to exit the CleverSpa® and unconsciousness resulting in the danger of drowning. WARNING – The use
of alcohol, drugs, or medication can greatly increase the risk of fatal hypothermia.
SAVE THESE INSTRUCTIONS
SPECIFIC REQUIREMENTS FOR THE SUCTION FITTING
• Required replacement of the suction fitting may only be performed by authorised representatives of Clever
Company Limited.
• This suction fitting is for surface mounted wall installation only, and can be classed as a self-contained hot
tub fitting for multiple outlet use only.
• Suction outlets must not be modified from the original position and located on seating areas or on the
backrests for such seating areas.
• When two or more suction fittings are used on a common suction line, they shall be separated
by a minimum of 3ft, or if any are located closer, they shall be located on two different planes.
• In the event that a suction outlet becomes blocked, the hot tub should not be used until the defective outlet is
fixed or replaced by an authorised representative. The remaining suction outlets serving that system shall have
a flow rating capable of the full flow of the pump(s) for the specific suction system.
• Only the pipework utilised in the original construction (OD/ID) can be used on this hot tub and cannot be
interchanged for other sizes.
• Wall mounted only.
• Suction fitting reference MX01.
• Replace within 3 installed year.
• Required replacement of the suction fitting may only be performed by authorised representatives of Clever
Company Limited.
• To protect the life of the suction fitting, the water in this hot tub should never be allowed to drop below 5oC, 41oF.
• The maximum flow rate through the suction fitting must not exceed 14 gpm.
• Before each use of the spa/hot tub, please inspect the suction fitting and its fastening for damage or tampering.
• We will state missing, broken or cracked/damaged suctions fittings must be replaced before use
• The suction fitting must be installed tightly, a loose fitting must be tightened before any use of the spa/hot tub.
• The flow rate through the suction fitting must not be increased through the introduction/use of an increased
capacity flow pump.
03
SAFETY INSTRUCTIONS
0
0.53 0.57 0.62 0.67 0.71 0.8 0.89
1.2
1.39
1.73
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
0 5 10 15 20 25 30 35
Total Head Loss (PSI)
Flow (GPM)
Flow vs Head Loss for Suction Fitting
Model No. MX01 (bbspa08500-20)
CLEVERSPA ETL US IM_FINAL.indd 3CLEVERSPA ETL US IM_FINAL.indd 3 07/01/2020 16:1707/01/2020 16:17

04
Please check all parts are present in your box before first use.
To order new or missing parts please visit: clevercompany.com
CLEVERSPA® PARTS CHECKLIST
FILTER CARTRIDGES (B)GROUNDSHEET (A)
SAFETY LOCKING
CLIP KEYS (H)
FILTER PROTECTOR
COVER (C)
CLIP-ON TOP COVER (E)INFLATION HOSE (D) REPAIR PATCHES (F)
DRAINAGE PLUG (G)
PRODUCT SPECIFICATION 71” CIRCULAR 82” CIRCULAR 73” X 73” SQUARE 71” CIRCULAR
ETL Model Number: 10001 10002 10003 10004
Capacity 2-4 People 4-6 People 4-6 People Up to 7 People
Water Capacity (approx.) 211 Gallons 264 Gallons 250 Gallons 270 Gallons
Actual Water Flow (approx.) 350 Gal/H 350 Gal/H 350 Gal/H 350 Gal/H
Inflated Size (approx.) 71” x 25.6” 82” x 25.6” 73” x 73” x 25.6” 71” x 25.6”
Product Weight (approx.) 53lbs 57.5lbs 57.5lbs 63.4lbs
Filled Weight (approx.) 1,830lbs 2,280lbs 2,160lbs 2,310lbs
No. of Bubble Jets 110 130 140 140
Pump Voltage 120V ~ 60Hz 12A 120V ~ 60Hz 12A 120V ~ 60Hz 12A 120V ~ 60Hz 12A
Maximum Temperature 104oF (40oC) 104oF (40oC) 104oF (40oC) 104oF (40oC)
Temperature Rise (approx.) 3-4oF/H (1.5-2oC/H) 3-4oF/H (1.5-2oC/H) 3-4oF/H (1.5-2oC/H) 3-4oF/H (1.5-2oC/H)
Rated Power Input for Heating 1200W 1200W 1200W 1200W
Rated Power Input for Bubbling 600W 600W 600W 600W
CLEVERSPA ETL US IM_FINAL.indd 4CLEVERSPA ETL US IM_FINAL.indd 4 07/01/2020 16:1707/01/2020 16:17

05
CLEVERSPA ETL US IM_FINAL.indd 5CLEVERSPA ETL US IM_FINAL.indd 5 07/01/2020 16:1707/01/2020 16:17

06
BEFORE YOU SET UP YOUR CLEVERSPA®
1. You must have solid support foundation where
you install your CleverSpa®. When setting up,
ensure there are no sharp objects that could
damage the CleverSpa® and the location is level
so the CleverSpa® sits properly.
2. During filling, emptying or when in use, water
may spill out. You should install it near to a
drainage point that is able to accept the total
volume of water.
3. Do not leave the surface of the CleverSpa®
exposed to direct sunlight for long periods
of time as this may affect the strength of
the welds.
Before setting up outdoors
1. Floor must be able to withstand
weight of the CleverSpa® + occupants.
2. Floor should be a non-slip, level surface.
3. Suitable drainage is essential when
installing your CleverSpa® indoor.
Carefully consider the placement
of your hot tub before installation.
Before setting up indoors
CLEVERSPA ETL US IM_FINAL.indd 6CLEVERSPA ETL US IM_FINAL.indd 6 07/01/2020 16:1707/01/2020 16:17

Unpack CleverSpa® on
groundsheet.
Uncoil cord and RCD/GFCI
plug, located under built-in
control unit.
Screw Hose (D) on to Air Outlet (J).
Unfold the CleverSpa® , ensuring
sides are as upright as possible.
Unscrew outer cap from Inflation
Valve (K). Do not unscrew the
black inner valve.
Connector Locations:
Air Outlet (J), Inflation Valve (K)
and Water Outlet (L).
J
J
D
K
L
K
07
SETTING UP YOUR CLEVERSPA®
Lay out groundsheet (A) on
a flat even surface, clear of any
sharp objects.
A
1
Remove protective plastic
from connectors.
4
Unscrew cap from Air Outlet (J).
J
7
Push the Hose (D) into
Inflation Valve (K). Plug into
mains and switch on.
K
D
10
2
5
8
3
6
9
Press ‘Inflate/Air Jets’ on control
panel to start inflation (red light
will appear).
11 12
To aid the inflation pull the sides
upright and spread out the base.
CLEVERSPA ETL US IM_FINAL.indd 7CLEVERSPA ETL US IM_FINAL.indd 7 07/01/2020 16:1707/01/2020 16:17

You can also see our Clever Clips on how to setup your CleverSpa® just visit clevercompany.com
08
Add water to level, no
higher than ‘Max’ level.
22
Screw Filter Cartridge (B)
on to Filter Connectors (N1 & N2).
B
20
J
D
J
Screw cap back
onto Air Outlet (J).
Unscrew Hose (D)
from Air Outlet (J).
Water Outlet (M)
Drainage Plug (G).
Filter Connectors
(N1 & N2) Drainage Plug (G).
M
N2
N1
G
18
19
16 17
Add the Filter Protector
Cover (C) onto the
Filter Cartridges (B).
C
21
Remove Hose (D) from
Inflation Valve (K).
D
KK
Screw cap back onto
Inflation Valve (K).
15
14
Once inflated, press the
‘Inflate/Air Jet’ on control panel
to ‘Stop’ inflation.
13
Set temperature on control panel*.
Clip on Top Cover (E) to retain the heat.
*See page 10 for full operating instructions.
Double lock clips with
Safety Locking Keys (H).
23 24
SETTING UP YOUR CLEVERSPA®
CLEVERSPA ETL US IM_FINAL.indd 8CLEVERSPA ETL US IM_FINAL.indd 8 07/01/2020 16:1707/01/2020 16:17

09
CLEVERSPA ETL US IM_FINAL.indd 9CLEVERSPA ETL US IM_FINAL.indd 9 07/01/2020 16:1707/01/2020 16:17

10
OPERATING YOUR CLEVERSPA®
SETTING THE TEMPERATURE
Press ‘SET TEMP/LOCK’ and the numbers on
display screen will start to flash. Increase/
decrease temperature by pressing ‘TEMP UP’
or ‘TEMP DOWN’.
Choose desired temperature, press ‘SET TEMP/
LOCK’ again to confirm. Temperatures can be
set between the range of 20°C to 40°C
(68oF - 104oF). (See safety instructions for
recommended operating temperatures).
INFLATE/AIR JETS
Press ‘INFLATE/AIR JETS’ to start air jets - a red
light will appear. Press again and air jets will
stop working - red light will go out.
Air jets stop automatically after 20 minutes.
To reset, wait for 10 minutes and press
‘INFLATE/AIR JETS. Air jets can be stopped/
started any time during their 20 minute cycle.
Air Jets will stop after 20 minutes to avoid
internal pump over-heating.
FILTRATION SYSTEM
Press ‘FILTER’, red light will appear, pump will
start to work. Press ‘FILTER’ again to stop pump,
red light will go out.
After approx. 168 hours, ‘FC’ will appear on
display screen (flashing), with a warning tone.
Red light will be lit on ‘FILTER’, pump will not
be operational. Heating system will also not
work and red light will be off.
To make sure filtration system is off, press
‘FILTER’. ‘FC’ on display screen will disappear
as well as warning tone. Water temperature will
be displayed, all functions will return to normal.
‘FC’ and warning tone remind user to replace filter.
‘FILTER
HEATER
Press ‘HEATER’, red light will appear.
Press ‘HEATER’ again and heating system
will stop, red light will go out.
When heater system is on, filter system will
switch on automatically to circulate water. When
temperature has reached 1°C above pre-set
temperature, heating system will stop working,
but light will remain on. Filter pump will
continue to operate even when heater
is not functioning.
When water falls 1°C below pre-set temperature,
heating system will automatically heat water
back to 1°C above selected temperature.
Once achieved, heater will stop to allow
temperature to settle at pre-set value.
CLEVERSPA ETL US IM_FINAL.indd 10CLEVERSPA ETL US IM_FINAL.indd 10 07/01/2020 16:1707/01/2020 16:17

11
MAINTENANCE & REPAIR OF YOUR CLEVERSPA®
WATER LEVEL
Water should be filled and maintained between ‘Min’ and ‘Max’ fill lines as indicated on inner wall
of your CleverSpa®
IMPORTANCE OF WATER TREATMENT
You need to regularly monitor and appropriately treat the water in your CleverSpa®.
PEOPLE WITH THE FOLLOWING TRAITS ARE AT HIGHER RISK INCLUDING:
• Diabetes, lung and heart disease • Smokers and heavy drinkers
• Anyone with an impaired immune system • People suffering from chronic respiratory or kidney disease.
For more information contact your doctor.
WATER AND LEGIONNAIRES DISEASE?
Legionnaires’ disease can be contracted by inhaling small droplets of water (called aerosols), which
are suspended in the air and contain the bacteria. Certain conditions increase the risk of Legionella if:
• Water temperature in all or some parts of the system is between 20-45°C (68°F-113°F), which is suitable
for growth of the bacteria.
• It is possible for breathable water droplets to be created and water is stored and/or re-circulated.
• There are deposits that can support bacterial growth providing a source of nutrients for the
organism e.g. rust, sludge, scale, organic matter and biofilms (from the body).
For more information visit: clevercompany.com/support/chemical-maintenance
CLEANING YOUR CLEVERSPA®
Detergent residues, dissolved solids from bathing suits and chemicals will gradually accumulate
in the water. To clean your CleverSpa®, use soap and water then rinse thoroughly.
Please note: do not use hard brushes or abrasive cleaners.
REPAIRING PUNCTURES IN YOUR CLEVERSPA®
If your CleverSpa® is torn/punctured, use repair patches. Completely dry area to be repaired, apply
strong adhesive to repair patch and then cover the damaged area. Smooth the surface to remove
any air bubbles. Leave to dry for 12 hours before using the CleverSpa®.
For more information cleaning and repairing your hot tub visit:
clevercompany.com/support/faqs/cleverspa-faqs
CLEVERSPA ETL US IM_FINAL.indd 11CLEVERSPA ETL US IM_FINAL.indd 11 07/01/2020 16:1707/01/2020 16:17

12
CLEANING & STORING AWAY YOUR CLEVERSPA®
HOW TO EMPTY YOUR CLEVERSPA®
1. Firstly, remove the CleverSpa® plug from the electrical mains.
2. Remove the screw cap from the water outlet (L) (below the pump system of the CleverSpa®) ensuring
the Drainage Plug (G) is still inserted to prevent unexpected draining.
3. Screw the inflation hose (D) onto the water outlet (L) and direct the open end of the hose appropriately.
4. Remove the drainage plug from the outlet within the floor of the CleverSpa®, so the water can flow out.
5. When the CleverSpa® is completely drained of water, you must operate the bubble function for 30
seconds to drain any remaining water from the pipeline.
6. When draining has finished, remove the inflation hose (D) and replace the drainage plug (G) and
water outlet cap (L).
HOW TO DEFLATE YOUR CLEVERSPA®
1. Locate the black two part air valve on the spa (see point 9) on ‘setting up your CleverSpa®’ item (K).
2. Fully unscrew and remove the rapid deflation air valve turning anti-clockwise (K).
3. Fold the spa away carefully to direct and remove as much air as possible through the open valve.
STORING YOUR CLEVERSPA®
Make sure all the water is completely drained from the CleverSpa® and pump system. This is vital in
extending the life of your CleverSpa®. We recommend the use of a wet/dry vacuum to blow out or
suck up water from the CleverSpa® pipes and pump lines. Remove the filter cartridge.
CleverSpa® should be placed in the bag provided and stored in a dry place, ideally raised off the floor
and away from any extreme temperatures.
Please note: Plastic becomes brittle and susceptible to breakage when exposed to subzero temperatures
and this can severely damage your CleverSpa®. Leaving your CleverSpa® outside and uncovered during
the winter months will void your warranty.
CLEANING THE WATER FILTER CARTRIDGE & MESH FILTER
If using your CleverSpa® 2-3 times per week, we suggest that you change your
filter every 2 weeks to maintain the best performance.
1. Remove the filter protector cover (C) and then remove the filter cartridge (B).
2. The filter cartridge can be rinsed periodically under a cold tap and reused.
However, if the filter cartridge remains soiled and discoloured the filter cartridge
should be replaced. If any holes are present in the paper filter or the paper
in the cartridge is noticeably worn, replace the filter with a new one before
further use. We DO NOT recommend the use of pressurised water to clean
any CleverSpa® filters.
3. Replace the filter protector cover (C) over the filter cartridge (B) and attach
to the filter connector (N1 & N2) by turning it clockwise until hand tight.
To help to keep your water clean, check your filter cartridge every day.
To order filters and chemicals for your CleverSpa®, please visit: clevercompany.com
FILTER
CARTRIDGE (B)
FILTER PROTECTOR
COVER (C)
CLEVERSPA ETL US IM_FINAL.indd 12CLEVERSPA ETL US IM_FINAL.indd 12 07/01/2020 16:1707/01/2020 16:17

13
TROUBLESHOOTING
PROBLEMS POTENTIAL CAUSES SOLUTIONS
A1 Air pump too hot
A2 Something wrong with
power box
A3 Air Pump in cooling mode
A1 Unplug system. After air pump has
cooled, insert plug and press air jets
button to activate
A2 Wait for 10 Minutes and restart
A3 Call CleverSpa® Aftersales if does not reset
A1 Temperature is set too low
A2 Dirty filter cartridge
A3 Improper water levels
A4 Heating element failure
A1 Set to a higher temperature 20-40°C
(68oF-104oF) than current water temperature
A2 Clean/replace filter cartridge
A3 Add water to specified levels
A4 Call CleverSpa® Aftersales if does not reset
A1 Dirty filter cartridge
A2 Something wrong
with power box
A1 Clean/replace filter cartridge
A2 Call CleverSpa® Aftersales if it does not reset
A3 Ask a professional electrician to check
household electrical supply
is functioning correctly
A1 Insufficient filtering time
A2 Dirty filter cartridge
A3 Improper water maintenance
A1 Increase filtration time
A2 Clean/replace filter cartridge
A3 Refer to chemical
manufacturer’s instructions
A1 CleverSpa® is torn or punctured A1 Use repair patch provided
SOME TIPS TO HELP YOU TO DIAGNOSE AND RECTIFY COMMON SOURCES OF TROUBLE:
Air jet system
is not operating
Heating system
does not operate
Filtering system
does not operate /
Rattling noise when
switching filter on
CleverSpa® leakage
Water not clean
A1 Residual water in the CleverSpa®
will continue to be heated
by residual temperature
A2 Water inlet through filter system
may be blocked
A1 Unplug from mains and wait.
Temperature will start to reduce
and return to normal
A2 Clean the inlet
A3 Call CleverSpa® Aftersales if does not reset
Display temperature
is higher than 40oC,
after stopping
heating function
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other household waste throughout the EU. To prevent possible
harm to the environment, or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse
of material resources. To return your used device, please use the return and collection systems or contact the retailer where the
product was purchased. They can take this product for environmental safe recycling.
Code Cause Solution
FC When filtration system has worked for approx.
168 hours, ‘FC’ will appear on display with a warning
tone. Red light will still be lit on filter, pump will
not be operational. Heating system will not
work, and red light will be out on heater.
SL/HL Temperature Issue
SH Water Temperature Sensor Issue
Check filter and change if necessary.
Once done, press filter again. ‘FC’ error
code will disappear, and warning tone
will stop. Water temperature will be
displayed, all functions will return
to normal.
Contact CleverSpa® Aftersales on:
[e-mail]
Contact CleverSpa® Aftersales on:
[e-mail]
CLEVERSPA ETL US IM_FINAL.indd 13CLEVERSPA ETL US IM_FINAL.indd 13 07/01/2020 16:1707/01/2020 16:17

14
CHANGED YOUR MIND AND NEED TO RETURN YOU HOT TUB?
PLEASE FOLLOW THE BELOW INSTRUCTIONS:
• If you have purchased a CleverSpa® and have simply changed your mind, follow the retailers instructions
for returns. You will need to register your warranty at: clevercompany.com/support/warranty and will
require proof of purchase.
DEFECTIVE ITEMS
If your item is defective in any way, i.e. it doesn’t work but you can’t identify why, in the first instance
please consult our FAQ section at clevercompany.com as there may be a simple solution to the
issue, if this does not help to resolve the issue, email: [e-mail] for assistance.
DAMAGED ITEMS
If you receive an order with obvious shipping damage from the retailer, then we suggest the delivery is
refused. If the delivery has been accepted and then shipping damage is found, please follow the specific
instructions advised by the retailer.
In all circumstances please save all packaging material and paperwork for the order. Please be aware that
if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller,
you jeopardise your chances of making a claim, and you may not receive a credit for the return.
LIMITS OF RESPONSIBILITY
CleverSpa® accept no responsibility for misuse or user damage and/or loss of parts incurred during
operation or use of the CleverSpa®.
This warranty relates to all CleverSpa’s bought in the US and covers the following areas:
• CleverSpa® Pump Heater: 12 months from the date of purchase
• CleverSpa® Cover & Liner: 6 months from the date of purchase
This warranty is not transferable if the goods are resold after the original purchase.
Your CleverSpa® is designed and manufactured for domestic use only. The CleverSpa® Warranty does not
extend to any commercial businesses operating in the rental of CleverSpa® hot tubs.
RETURNS
CLEVERSPA ETL US IM_FINAL.indd 14CLEVERSPA ETL US IM_FINAL.indd 14 07/01/2020 16:1707/01/2020 16:17

REGISTERING YOUR WARRANTY
To register your warranty, visit clevercompany.com/support/warranty and complete the form within
28 days of purchase. The warranty will start from the date of purchase which must be verified by proof
of purchase.
For up-to-date troubleshooting advice, technical information and FAQs please visit our online help
centre at [e-mail].
WARRANTY CLAIMS
Before making a claim, we may be able to answer your query, simply visit clevercompany.com/support/
cleverspa-faqs for further information.
If the FAQs don’t solve the issue and you need to make a claim, please ensure that you have registered
your warranty and contact us by email at: [e-mail]. Our dedicated Aftersales
Team will endeavour to answer all messages within 48 hours.
15
WARRANTY
CLEVERSPA ETL US IM_FINAL.indd 15CLEVERSPA ETL US IM_FINAL.indd 15 07/01/2020 16:1707/01/2020 16:17

Clever Company Ltd. UK Address: Oldgate, St.Michael’s Industrial Estate, Widnes, Cheshire, WA8 8TL.
European Address: Radarweg 29, 1043 NX Amsterdam, Netherlands.
General Enquiries, Returns, Spare Parts, Repairs & Chemical Advice
visit: clevercompany.com
SAFETY SIGN POSTING
Please post the ‘Safety Sign’ provided in an area visible
to all users of the hot tub, to alert them of the safety rules and warnings.
REPLACEMENT SAFETY SIGN
To obtain additional or a replacement ‘Safety Sign’, please contact
Clever Company on [e-mail].
EXAMPLE SAFETY SIGN
CLEVERSPA ETL US IM_FINAL.indd 16CLEVERSPA ETL US IM_FINAL.indd 16 07/01/2020 16:1707/01/2020 16:17