CLEVERSPA 180CM CIRCULAR User manual

INSTRUCTION
MANUAL
06-09-21
PLEASE DON’T RETURN YOUR SPA TO STORE!
CONTACT CLEVERSPA®AFTERSALES FOR
ASSISTANCE. [e-mail]
Due to Clever Company’s continuous product improvement process, Clever Company reserves the right to change the
specifications and appearance of its products, which may result in updates to the instruction manual without prior notice.

CONTENTS
SAFETY PRECAUTIONS 04-05
INSTALLATION AND OPERATIONAL INFORMATION 06-07
CLEVERSPA®PARTS CHECKLIST 08-09
SETTING UP YOUR CLEVERSPA®10
CLEVERLINK® APP SETUP 11
LED LIGHTING SETUP 12
OPERATING YOUR CLEVERSPA®13
MAINTENANCE & REPAIR 14
FILTER REPLACEMENT & CLEANING TIPS 15
TROUBLESHOOTING 16-17
WARRANTY 18
RETURNS 19
WELCOME TO THE WORLD
OF CLEVERSPA®
The perfect way to chill out with family and friends, while you
enjoy the laid-back vibe with a cold drink. You are now part of
the relaxing and rejuvenating CleverSpa®hot tub experience.

Follow the precautions below to ensure that your product is used and set up correctly.
Failure to do so could result in serious injury or damage to your property. Please read and
follow the instructions. Keep the instruction manual in a safe place for future reference.
DROWNING AND SAFETY INFORMATION
• RISK OF ACCIDENTAL DROWNING. Children are forbidden from using the CleverSpa®unless they are supervised
at all times by a responsible adult.
• DANGER — Risk of Accidental Drowning (especially children under 5 years). Caution shall be exercised to prevent
unauthorized access to the spa by children. This can be reached by adult supervisor securing the means of access
or installing a safety protection device to the spa. To avoid accidents during spa use, ensure that children are kept
under constant adult supervision.
• RISK OF ELECTRIC SHOCK. Never operate any external/additional electrical appliance when in the CleverSpa®
or when your body is wet. Keep electrical appliances away from the CleverSpa®.
• RISK OF STATIC SHOCK. The PVC liner of the tub, touching or rubbing against surfaces such as the ground
sheet or artificial grass, can cause electrons to build up a negative charge on the liner material. Since plastics
are insulators, they are poor conductors of electricity. Electrical charges tend to build up on the surface
of insulators resulting in static electricity. When touched by a human this can cause a static shock. Static
electricity cannot seriously harm you.
• Any damage to electrical cables should be replaced by a competent party immediately before further use.
• When not in use, cover should be fitted and locked to help retain heat. This also prevents unsupervised children
accessing the CleverSpa®.
• Pets should be kept away from your CleverSpa®at all times.
• DO NOT USE AN EXTENSION CABLE as this can be a fire risk. We suggest using an external mains socket that
is weather proofed, fitted by a qualified electrician.
• DO NOT OVERLOAD THE HOT TUB PLUG SOCKET. Short circuits can cause loss of power due to overloading
of the socket and potentially melt the wiring, which can lead to an electrical fire or irreparable damage to the
socket and any appliances connected to it.
• Appliance should be supplied through a residual current device (RCD/GFCI type) with a rated tripping current
not exceeding 30mA.
• Ensure the hot tub plug inserts fully into the plug socket, fitting tightly and flat into the socket and wall to avoid
arcing and overheating, which could cause the socket to crack or melt.
• Check your mains socket and RCD plug to ensure there is no visible damage or standing water before using.
• To avoid accidental resetting of thermal cut-out, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is regularly switched on and o by the utility.
• If using an outdoor power socket please ensure that it features a weatherproof protective cover, that shuts fully
and securely.
• Ensure that your power socket and its surrounding location is free from damp, condensation or any water ingress.
Water within an electrical socket can rapidly increase the current flowing through the circuit, which could cause
a short circuit as the fuse is blown.
• Do not turn CleverSpa®on when it is empty. This could cause irreparable damage to pump system which would
nullify any warranty period. Ensure water is at the minimum line prior to switching on.
04
SAFETY PRECAUTIONS - READ CAREFULLY!
IMPORTANT!
Do not obstruct water outlet.
This can damage the motor.

05
SAFETY PRECAUTIONS - READ CAREFULLY!
• WARNING — To reduce the risk of injury/illness. The water in a spa should never exceed 40°C (104°F). Lower water
temperatures are recommended for young children and when spa use exceeds 10 min. It is recommended to seek
medical advice before use. Operating temperatures between 38-40°C (100-104°F) are considered safe for a healthy
adult. The temperature can be programmed. Once cover is removed, water temperature may automatically drop as
heat is released through evaporation.
• For health & safety reasons, it is not safe for children under the age of 8 yrs to use a hot tub. Children using hot
tubs over the age of 8 yrs should only use the hot tub at a max temperature of 35°C (95°F) as children are less
able to regulate their body temperature.
• The user should check the water temperature before entering the spa.
• Soaking in hot water during pregnancy can cause damage to the unborn foetus. If you have any specific concerns
please consult your doctor before continuing to use your hot tub.
• People with the following traits are at higher risk and should consult a doctor before using CleverSpa®x , including
those with history of lung or heart disease, chronic respiratory or kidney disease, impaired immune system, low/
high blood pressure, circulatory system problems or diabetes. People using medication should consult their
doctor before using the CleverSpa®. Some medications may cause drowsiness, whilst other medication may aect
heart rate, blood pressure and circulation during use.
• The use of alcohol, drugs, or medication before or during spa use may lead to unconsciousness, with the
possibility of drowning.
• Persons with any medical condition should seek medical advice before using a spa.
• Persons using medication should seek medical advice before using a spa since some medication may induce
drowsiness while other medication may aect heart rate, blood pressure, and circulation.
• Avoid putting the head under water at all times.
• Avoid swallowing spa water
• Immediately exit your CleverSpa® if you feel uncomfortable or sleepy.
CAUTION
• Regularly monitor and appropriately treat the water in your hot tub using the recommended chemicals.
• Always add chemicals to a jug of water (not the other way around) to avoid strong fumes or violent reactions
that may result in a hazardous chemical spray. This will also help prevent the inside of the hot tub from becoming
discoloured.
• Legionnaires’ disease can be contracted by inhaling small droplets of water (called aerosols), which are
suspended in the air and contain the bacteria. Certain conditions increase the risk of Legionella if the water
temperature is between 20-45°C (68oF-113oF), which is suitable for growth of the bacteria. Deposits that can
support bacterial growth providing a source of nutrients for the organism e.g. rust, sludge, scale, organic matter
and biofilms (from the body).
• Hot tub rash, or folliculitis, is a skin infection with symptoms including itchy red spots on the skin or pus-filled
blisters around hair follicles. To avoid this, ensure your Chlorine and pH levels are checked at least twice per
day using test strips - hot tubs with good disinfectant and pH control are less likely to spread germs. For more
information visit: clevercompany.com/support/chemical-maintenance.
• Shower before using your CleverSpa®. Fake tan, suncream and other cosmetic products, can degrade water
quality and block the filter.
• Blocked filters can damage your pump and heater, which could ultimately cause it to break. Clean your filters
regularly, rotating 2-3 filters, in order to always have a clean filter to hand. See filter cleaning tips page 13.
• Extreme temperature fluctuations can be caused by blocked filters when the motor is unable to draw enough
water into the system. A small amount of water will still remain in the heating reservoir (approx 300ml).
Although the thermostat will turn the element o once the set temperature is reached, the residual heat from
the element will continue to heat the small amount of water in the reservoir until the heating element has
cooled. This may cause the control panel to display an artificially high reading, not reflecting the actual water
temperature. The hot tub is fitted with an ‘Overheat Protection’ function which will activate the HL error code
and a warning beep. See error codes for solution.

SAFETY INSTRUCTIONS - READ CAREFULLY!
• SUPPORTING THE HOT TUB - There is a requirement that the support materials shall be strong enough to
support the maximum design load of the spa, spa water and bathers. Recommendation to ask a qualified
contractor or a structural engineer to verify this requirement. Special attention should be given where the spa
is to be installed on a suspended floor (e.g. balcony, decking and roof terrace). In these instances the client/
consumer shall be advised of the full load weight of the spa, including any fixtures and fittings (e.g. gazebo), so
that they can obtain structural calculations from a structural engineer.
• The surface must be smooth, flat, level and capable of evenly supporting the weight of the CleverSpa®, water and
users e.g. 6 Person Square CleverSpa® filled weight: 980kg (approx) plus combined weight of occupants. It is the
responsibility of the CleverSpa® owner to assure integrity of the site at all times.
• Insulate the base of the hot tub, using a foam mat, to reduce heat loss.
• Ensure the area is free of sharp objects under or around the hot tub.
• Consider the best placement of the hot tub to allow for draining of the water during disassembly.
• Ensure there is adequate drainage to deal with any overflow of water.
• Consideration for positioning of the spa to minimize noise disturbance as much as possible.
• Dirt entering the hot tub could cause damage to the hot tub floor and could cause the filter to block.
• DO NOT OVERINFLATE YOUR HOT TUB - Air space needs to be left inside the wall of the hot tub to allow
for air expansion (during warmer weather) and contraction (during colder weather).
Do not place your hot tub in direct sunlight.
If this advice is ignored, the wall and rim of the hot tub could bulge during warmer weather as the PVC heats
up, putting additional stress on the internal welds, this causes weld failures.
In both of these instances, the warranty would be void. (See page 14 showing correct inflation).
• If applicable, requirements for protecting the spa from direct sunlight exposure when not in use, and the means
provided or recommended for it.
• Do not switch on if there is any possibility that water in the CleverSpa® or control system is frozen.
• Your hot tub is fitted with 365 FreezeGuard Technology, to help prevent water freezing and to protect your
pump & heating system during colder weather. This is activated by pressing the 365 Freezeguard button on
your control panel.
• During colder weather the hot tub should only be kept outside if the 365 FreezeGuard feature has been activated.
Failure to do this could cause water to freeze within the pump & heating system causing irreparable damage, thus
voiding your warranty.
• Do not attempt to lift or drag the hot tub after filling it with water.
• Check the set water temperature and consider lowering it for the times when the spa will typically not be in use.
• Depending on external conditions, consider turning o the heater entirely if not using the spa for an extended
period of time (where the spa provides this option, but still maintains residual disinfection/pH-values).
• Consider that the comfortable temperature range during use may be lower than the maximum safe temperature.
• For above ground portable spas without floor insulation, consider using an insulating ground cloth underneath
the spa to minimize heat loss through the bottom of the spa.
• Maintain clean filters to preserve appropriate working conditions for the pump and avoid unnecessary water
replacement and re-heating.
• Water in the hot tub should never exceed 40°C (104°F). Operating temperatures between 38-40°C (100-104°F)
are considered safe for a healthy adult. We recommend lower temperatures when using the hot tub for longer
than 10 continuous minutes. The temperature can be programmed. Once cover is removed, water temperature
may automatically drop as heat is released through evaporation.
• In the absence of automated and/or continuous water treatment (measurement and chemical dosage) any
manual dosing of chemicals shall not be performed while bathers are present in the spa.
INSTALLATION AND OPERATIONAL INFORMATION
06

SAFETY INSTRUCTIONS - READ CAREFULLY!INSTALLATION AND OPERATIONAL INFORMATION
WATER DRAINAGE
• Consideration for a draining system around/under the spa to evacuate to waste the water poured by the bathers
exiting the spa, splashes, (abnormal) leaking, accidental overflow etc., for regular cleaning of the spa and its
surroundings, and regular emptying of the spa or during long term spa storage. Special attention should be given
to areas that have high water tables, are prone to flooding and/or are sited indoors. Drainage to the surround
should be sucient to allow wash down. Where non-porous duckboard type flooring is used, it shall be provided
with drainage under to waste and facilities to clean and wash beneath and consequently be easily removed.
THE TOP COVER
• When the hot tub is not in use, always keep the cover fitted, this helps minimize heat loss between uses / during
heating. Ensure the cover is fitted tightly, as directed to maximize insulation. When the cover is not in use it should
be stored in an appropriate location, where it cannot be damaged, or cause damage. The cover should be stored
in a clean, dry area, otherwise it can pick up dirt and bacteria. We recommend that the cover is kept o the
ground to retain its cleanliness (particularly the surface in close proximity to the water spa water surface). Covers
should not be put on wooden tables or wooden decking because of the risk of bleaching the wood. A cover lifter,
or similar device, is useful for ensuring that the cover does not come into contact with the ground. Top covers shall
be cleaned inside and out periodically using a suitable solution that includes adequate disinfection (e.g. 10 mg/l
of Free Chlorine).
OUTDOOR INSTALLATION
• The need to take into consideration local environmental conditions, such as ground water and risk of frost and for
those professional installers to include a discussion of these conditions with the client.
INDOOR INSTALLATION
• Advice for suitable air treatment in the spa chamber (ventilation and dehumidification) to preserve the bathers’
safety/comfort and the building and decorative materials present in the chamber.
• Consider not to installing the spa on carpet or other floor materials (e.g. untreated cork, timber or other porous
materials) that promote or harbour moisture and bacteria, or that could be aected by water treatment chemicals
used in the spa.
• Consider that it should remain possible to remove the spa from the chamber/building without destroying
part of the built structure.
• Spa surround Barefoot areas and relaxing areas shall be considered in the cleaning process as well. No cleaning
water may flow into the spa or spa water cycle. The dirt and cleaning agents shall be rinsed carefully to drain in
the spa surround.
07

Please check all parts are present in your box before first use.
To order new or missing parts please visit:
clevercompany.com
SQUARE I-BEAM HOT
TUB INSTRUCTIONS
SAME AS ROUND
I-BEAM HOT TUB
PRODUCT SPECIFICATION 180CM CIRCULAR 208CM CIRCULAR 185CM SQUARE
CAPACITY 2-4 People 4-6 People 4-6 People
WATER CAPACITY (APPROX.) 800L 1000L 950L
ACTUAL WATER FLOW (APPROX.) 1,325L/H 1,325L/H 1,325L/H
INFLATED SIZE (APPROX.) 180 x 65cm 208 x 65cm 185 x 185 x 65cm
PRODUCT WEIGHT (APPROX.) 24kgs 26kgs 26kgs
FILLED WEIGHT (APPROX.) 830kgs 1,035kgs 980kgs
NO. AIR JETS 110 130 140
PUMP VOLTAGE 220-240V–50Hz 220-240V–50Hz 220-240V–50Hz
MAXIMUM TEMPERATURE 40oC (104oF) 40oC (104oF) 40oC (104oF)
TEMPERATURE RISE (APPROX.) 1.5-2oC/hr 1.5-2oC/hr 1.5-2oC/hr
RATED POWER INPUT - HEATING 1800W 1800W 1800W
RATED POWER INPUT - BUBBLING 600W 600W 600W
RATED CURRENT - HEATING/BUBBLING/FILTERING 10.4A: Heat 7.8A & Bubble 2.6A) 10.4A: Heat 7.8A & Bubble 2.6A) 10.4A: Heat 7.8A & Bubble 2.6A)
CLEVERSPA®PARTS LIST
09
AIR OUTLET/
CAP
DRAINAGE OUTLET/CAP
INFLATION VALVE/
CAP
J
L
K
CLIP-ON TOP
COVER
DRAINAGE PLUG
FILTER COVER
FILTER CARTRIDGE
FILTER CONNECTOR
WATER OUTLET
G
N
M
E
DESCRIPTION CODE
GROUNDSHEET A
FILTER CARTRIDGE B
FILTER COVER C
INFLATION HOSE D
TOP COVER E
REPAIR PATCHES F
DRAINAGE PLUG G
LOCKING KEYS H
OUTLET CAPS J / L
INFLATION VALV E K
LED LIGHTING KIT X(WHERE APPLICABLE)
B
C
(PRE-FITTED)
(PRE-FITTED)

SETTING UP YOUR CLEVERSPA®
10
Lay groundsheet (A)
on a flat, even surface,
clear of sharp objects
Screw Hose (D)
on to Air Outlet (J)
Once inflated,
press on control panel
to stop inflation
Add Filter Protector Cover (C)
onto Filter Cartridge (B)
Fill with fresh tap water
Fully uncoil the lead & plug,
located under the
pump & heating system
Connectors: Air Outlet (J),
Inflation Valve (K)
Water Outlet (L)
Push Hose (D)
into Inflation Valve (K)
Plug into mains & switch on
Ensure caps are screwed
back on after inflation
Set desired temperature
on control panel*
Clip on Top Cover (E)
Press on control panel
to start inflation
(Light will appear)
Screw Filter Cartridge (B)
onto Filter Connector (N)
Double lock clips with
Safety Locking Keys (H).
J
K
L
D
DK
J
DO NOT OVER INFLATE!
WITH LIGHTS - INSERT LED STRIP BEFORE
FILLING. WITH CLEVERLINK®- POSITION
HOT TUB FIRST
DO NOT UNSCREW INNER VALVE!
B
N
C
*PAGE 09 - SETTING TEMPERATURE
1. 2. 3.
4.
7. 8. 9.
10. 11. 12.
5. 6.

FAIR
STRONG
WEAK
11
CLEVERLINK®APP SETUP - SELECTED MODELS ONLY
DOWNLOAD THE APP
1. Open the App Store on (Apple devices) or
Play Store on (Android devices).
2. Search CleverLink®and download the app.
3. Once CleverLink®is installed on your device,
tap the icon to launch.
CONNECTING YOUR CLEVERSPA®
4. On first launch you will be asked to register a new
CleverSpa®account.
5. Complete the relevant fields on the sign-up form.
6. Read the terms and conditions and tick the boxes.
7. Press the “Sign Me Up” button to sign-up.
For best signal quality we recommend the use of a
2.4GHz WiFi range extender.
PAIRING YOUR CLEVERSPA®
Once you have successfully logged into the CleverLink®
App you will be taken through the pairing steps.
8. Ensure the device you are using for setup is
connected to the same 2.4GHz network that you
would like to connect your CleverSpa®hot tub to.
9. Select the control panel version that your hot tub
is fitted with.
10. Input the Network name and security password
for your wireless network. This can usually be found
on your wireless router.
11. Review the tip about hot tub placement (as above),
and press ‘NEXT’.
12. Hold the CleverLink®Pairing button on your hot
tub until you hear the beep, tick the confirmation
box on screen and tap ‘Pair your CleverSpa®’.
13. The CleverLink®will now try to establish a connection
between your device and your CleverSpa®hot tub.
This can take up to 60 seconds to complete.
14. Once the pairing process is complete you should
see a Green Tick. Click “finish” to finalise the process.
15. Once you see the green tick, activate a function
on the hot tub control panel such as the airjets.
This will sync the control panel and app.
If you see the Red Cross “Pairing Failed” on screen, try
completing the pairing process again. Be sure to check
your wireless network settings are correct and that the
CleverSpa®is within range of the network.
BEFORE SETTING UP YOUR CLEVERLINK®OUTDOORS
FIND THE STRONGEST STRONG WIFI SIGNAL
Before filling your CleverSpa®, check that the hot
tub is in range of your wireless network*. Check the
signal strength by looking for the wireless network
symbol on your phone. The more bars the better
signal quality.
The bars will adjust as you move location showing
the dierent signal strengths. Find a location with a
strong WiFi signal before setting up your CleverSpa®
hot tub and filling it with water.
*CleverLink®supports 2.4Ghz Wireless networks
STRONGER SIGNAL CLOSER TO THE HOME ROUTER
SCAN ME FOR
CLEVERLINK®
SETUP
FOR BEST SIGNAL QUALITY WE RECOMMEND THE USE OF A 2.4GHzWIFI RANGE EXTENDER
For more help visit: clevercompany.com/support/troubleshooting

FIT THE LED LIGHTS LOOSELY TO ALLOW THE CLEVERSPA®TO EXPAND WHEN FILLED.
Correct installation of your LED lights is extremely important. Failure to follow instructions carefully
may result in failure.
Ensure lights are not installed too tightly. They must be fitted loosely, with freedom to move between
the retention loops on the base of the hot tub. Allow for some excess LED strip across each gap, this
will reduce stress on the lighting. This allows the lighting strip to expand when filled with water.
Failure to do this can reduce the lifespan of your lighting - please see FIG 1 below.
RF Wireless
Receiver
LED
Light Strip
23
1
Mains Power
Converter
RF REMOTE
CONTROL
& CR2025
3V BATTERY
IMPORTANT! Note the placement of alignment notches
HOW TO CONNECT THE LED LIGHTING KIT
LED LIGHTING SETUP - SELECTED MODELS ONLY
12
INITIAL LIGHTING SETUP
1. Connect lighting system together as shown in FIG 1.
2. Remove plastic tape from the battery compartment
on the remote.
3. Turn lights on with the power button.
INSTRUCTIONS
MODE
+
SPEED
+
SPEED
–
MODE
–
COLOR
+
COLOR
–BRIGHT –
BRIGHT
+
DEMO
RF Wireless
A
CG
F
E
D
B
POWER
On / Standby
CHANGE MODE
Forwards / Backwards
CHANGE SPEED OF LIGHTS
‘+’ Faster / ‘–’ Slower
CHANGE COLOURS
Forwards / Backwards
PRE-SET COLOURS
Select from a range of
pre-set solid colours
BRIGHTNESS
Adjust Lighting
brightness (5 levels)
: Increase Brightness
: Decrease Brightness
DEMO MODE
Cycles through pre-set
colours & eects
A
B
C
D
E
F
G
+
–
LIGHTING DOES NOT CORRESPOND TO COLOUR SELECTED
1. Turn on the lights using the red power button.
2. Press the solid green button once.
3. Turn o the power at the mains for 5 seconds.
4. Turn back on and immediately press and hold
the solid green button.
5. Release the button when the colour changes to green.
6. Wait 5 seconds for the change to take eect.
N.B. Style of CleverSpa®
may dier from image shown
FIG 1
START/END LIGHTING
EQUALITY SPACED
ENSURE LIGHTING IS NOT TIGHT BETWEEN
LOOPS AND LEDS FACE THE BASE
FIRST LIGHTING LOOP LAST LIGHTING LOOP
N.B. When changing the battery in the remote control, replace with
a suitable CR2025 3V battery inserted with the + Symbol facing up.

HEATER
HEATER
365 FREEZEGUARD WIFI CONNECT
INFLATE
AIR JETS
INFLATE
AIR JETS
FILTERFILTER TEMP UP TEMP UP
SET TEMP/
LOCK
SET TEMP/
LOCK
TEMP DOWN
TEMP DOWN
13
OPERATING YOUR CLEVERSPA®
CONTROL PANEL CONTROL PANEL WITH CLEVERLINK®
Press SET TEMP/LOCK and the numbers on display screen
will start to flash. Increase/decrease temperature by pressing
TEMP UP or TEMP DOWN.
Choose desired temperature, press SET TEMP/LOCK again to
confirm. Temperatures can be set between the range of
20°C - 40°C.
See safety precautions for recommended operating temperatures.
Press INFLATE/AIR JETS to start the bubbles - a light will appear.
Press again and air jets will stop and the light will go out.
INFLATE FUNCTION:
Do not overinflate. Do not leave unattended.
Air Jet Function:
Air jets will stop automatically after 20 minutes of continuous use,
to avoid internal pump overheating. They can be started again
after 10 minutes (indicated by beep). Air jets can be stopped or
started again at any time during their 20 minute cycle.
SETTING THE TEMPERATURE
Press HEATER, light will appear. Press HEATER
again and heating system will stop, light will go out.
When heater system is on, filter system will switch on
automatically to circulate water.
When temperature has reached 1°C above pre-set
temperature, heating system will stop working,
but light will remain on. Filter pump will continue
to operate even when heater is not functioning.
When water falls 1°C below pre-set temperature, heating
system will automatically heat water back to 1°C above
selected temperature. Once achieved, heater will stop
to allow temperature to settle at pre-set value.
HEATER
INFLATE/AIR JETS
FILTER CHANGE
FILTER
Press FILTER, light will appear, pump will start to work.
Press FILTER again to stop pump, light will go out.
After approx. 168 hours, FC code will appear on display screen.
It reminds users to check/replace their filter.
NOTE: The filter should be cleaned after every use.
See ‘Cleaning filter tips’ on page 15.
Light will be lit on FILTER. Pump and heating system will
continue to operate as normal and lights will be on.
To clear the FC code, press FILTER. the FC on display screen
will disappear and the water temperature will be displayed.
All functions will return to normal.
IMPORTANT! FILTER CYCLE
After the pump and heater is turned o, the filter will
continue to run for a couple of minutes to avoid overheating.
The filter light will flash during this time.
DO NOT REMOVE THE FILTER UNTIL THE CYCLE HAS
COMPLETED TO AVOID DEBRIS GETTING INTO THE
SYSTEM, CAUSING POTENTIAL DAMAGE. For instructions on how to connect you CleverLink® App
see page 11.
When switched on, 365 FREEZEGUARD will activate the
filter and heater and maintain the water temperature at
5°C to help prevent the water freezing at low temperatures.
Press 365 FREEZEGUARD, light will appear, filter and heater
will be activated & lights will appear. Controls will be disabled.
Press 365 FREEZEGUARD again, lights will go out, filter and
heater will be deactivated, all control will be re-enabled.
365 FREEZEGUARD
CLEVERLINK®

USING CLEVERSPA® FOR THE FIRST TIME
If you are using your hot tub for the first time, or
have changed the water, you will need to chemically
‘Shock’ your hot tub water. Shocking the water in your
CleverSpa® hot tub will sanitise the water ensuring it is
safe to bathe, destroying any bacteria.
Good chemical maintenance is very important and
will reduce the number of times your CleverSpa®
requires fresh clean water.
HARDWATER/LIMESCALE
If you live in an area with hard water, you may
experience limescale build up and residue in your
CleverSpa® pump & heating system which could
significantly reduce the lifespan of some internal
components, stopping the hot tub from working.
In order to reduce the eects of limescale build up
please check the water hardness in your area. If you
are aected please ensure that CleverSpa® Descaler is
used weekly to prevent scale formation and build up.
CLEANING YOUR CLEVERSPA®
To clean your CleverSpa®, use soap and water then
rinse thoroughly. PLEASE NOTE:do not use hard
brushes or abrasive cleaners. For best results we
recommend the use of our CleverSpa® Sponge.
REPAIRING PUNCTURES IN YOUR CLEVERSPA®
If your CleverSpa®is torn/punctured, use repair
patches. Completely dry area to be repaired, apply
strong adhesive to repair patch and then cover the
damaged area. Smooth the surface to remove
any air bubbles. Leave to dry for 12 hours before
using the CleverSpa®.
HOW TO EMPTY YOUR CLEVERSPA®
1. Remove CleverSpa®plug from electrical mains.
2. Unscrew cap from drainage outlet (L) below pump
system of CleverSpa®. Ensure Drainage Plug (G)
is still inserted to prevent unexpected draining.
3. Screw inflation hose (D) onto the water outlet (L)
and direct open end of hose appropriately.
4. Remove drainage plug from outlet within floor
of CleverSpa®, so water can flow out.
5. Once drained use a sponge to absorb excess water;
then operate air jet function for up to 20 minutes (one
full cycle) to drain any water and dry out the pipeline.
If not completely dry after first cycle – repeat.
6. When draining has finished, remove inflation
hose (D) and replace drainage plug (G) and
outlet cap (L).
HOW TO DEFLATE YOUR CLEVERSPA®
1. Locate the black two-part air valve (K).
2. Fully unscrew and remove rapid deflation
air valve by turning anti-clockwise (K).
3. Fold hot tub away carefully to remove as much
air as possible through the open valve.
STORING YOUR CLEVERSPA®
Make sure all water is completely drained from
the CleverSpa®and pump system. This is vital in
extending the life of your CleverSpa®. We recommend
the use of a wet/dry vacuum to help blow out/
suck up water from pipes and pump lines. Remove
filter cartridge. CleverSpa®should be placed in bag
provided and stored in a dry place, raised o floor
and away from extreme temperatures. Please note:
When not in use, store in a place that is dry and a
moderate temperature, as subzero temperatures
can severely damage your CleverSpa®.
CORRECT INFLATION
How do I know my hot tub is inflated correctly?
Here is an example image of the correct inflation
level for a standard hot tub. Once inflated correctly
you should be able to push your hand approximately
4-5cm into the top rim using moderate force creating
creases similar to the picture above. Keeping your
hot tub inflated to the correct pressure ensures
optimum liner performance, reducing the risk of
ripping and seam failures.
OVER INFLATION
How do I know how much air should I inflate
my hot tub with?
If you are not able to push your hand into the
rim of the hot tub by approximately 4-5cm with
moderate force, then your hot tub is over-inflated.
An over inflated hot tub can result in ripping or
disfiguring the liner and seriously damaging the
hot-tub all-together.
14
MAINTENANCE & REPAIR

WHEN TO CHANGE A CLEVERSPA®FILTER
Keep your CleverSpa® hot tub clean and safe from
contaminants. For optimum performance, unscrew
the filter and rinse with clean water after every use to
remove any small particles and residue.
The filter is one of the most important elements to
ensure your CleverSpa®hot tub works eectively.
1. Turn o the filter at the control panel to prevent
any debris being drawn into the motor
2. Remove filter ‘sock’ protective cover (C) then
remove filter (B).
3. Rinse the filter under a cold tap and reuse.
Alternatively, machine wash your filter (place
in a pillowcase) to keep it clean and to maintain
its performance.
Rotate the cleaning of 2-3 filters to ensure you always
have a clean filter available ready to use.
REPLACE OLD FILTER WITH A NEW ONE IF:
• The filter remains soiled after cleaning
• Holes are visible in the paper
• The paper is noticeably worn
Replace filter ‘sock’ protective cover (C) over
filter (B) and attach to filter connector (N)
by turning it clockwise. Do not over tighten,
as this may cause a ‘rattling’ noise.
REMEMBER - CLEAN AFTER EVERY USE!
The filter is one of the most important elements to
ensure your CleverSpa®hot tub works eectively.
CLEVERSPA®
FILTER AFTER USE
Please note - the more
frequently you use your
hot tub the quicker your
filters will become dirty.
CLEANED IN A
DISHWASHER
Place on a quick cycle
using a dishwasher tablet.
We highly recommend
cleaning your filters in
an empty dishwasher.
CLEANED IN A
WASHING MACHINE
Place on a quick cycle
using normal detergent.
We recommend placing
your filters inside a pillow
case or in a towel to
reduce noise.
HOT TUB ‘SOAK
FILTER CLEANER
Using CleverSpa®‘Soak’
Filter Cleaner, will ensure
optimum Filter
performance.
FILTER REPLACEMENT & CLEANING TIPS - IMPORTANT!
TO ORDER FILTER CLEANER - PLEASE VISIT: CLEVERCOMPANY.COM
TIPS FOR CLEANING YOUR CLEVERSPA® FILTER
15
IMPORTANT!
If your hot tub is making an unusual
noise, your filter needs removing
and cleaning or changing.
The frequency of use and condition
of your filter will determine how
often your filter needs changing.
SCAN ME
FOR FILTER
CLEANING TIPS

TROUBLESHOOTING
CONTROL PANEL ERROR CODES
The FC error code, with a small light
beside it, will appear when the filtration
system has worked for approx 168 hours
advising you to check your filter. The
pump & heating buttons will be disabled.
An HL error usually means there is
a blockage, preventing water from
circulating around the pump & heating
system. The blockage can be caused
by a dirty/old filter, a blocked impeller
or limescale build up – especially if
you live in an area with hard water.
Check here:
www.aquacure.co.uk/knowledge-
base/uk-hard-water-map
This can cause an artificially high
temperature reading to be displayed
on the control panel.
Checking for water flow.
1. Place your hand into the water approx. 6-8 inches away from the outlet.
2. You should feel the water flowing through the outlet valve.
If the flow rate is very weak or non-existent or your hot tub is making an
excessive rattling/grinding noise, follow the steps below.
1. Ensure that your filter has been cleaned. Check out our filter
maintenance advice.
2. Be sure to also clean and rinse the protective filter cover.
3. Replace your filter with a new one.
4. Ensure the filter is not overtightened.
Remember: Sun cream, fake tan, soap etc can force the motor to work much
harder as these can clog a filter faster. See filter cleaning tips section.
I have cleaned my filter but my CleverSpa® still hasn’t heated?
Please try the following steps:
1. Turn o the filter and heater.
2. Remove the protective filter cover and filter.
3. Place the filter cover over the filter inlet and use an elastic band to hold
it in place. This helps prevent debris being drawn into the pump while
there is not filter fitted.
4. Press the ‘Heater’ button on and re set the temperature on the control panel.
5. If the temperature now begins to rise and maintain its temperature it is
likely that your filter needs replacing.
6. Please replace your old filter with a new one. Check out our filter
maintenance information.
Limescale Blockage
Many areas have hard water, causing limescale build up within home appliances.
As with other products we strongly advise that you incorporate a descaling
routine into your hot tub maintenance schedule to reduce the eects of
limescale build up.
We recommend that the CleverSpa® Descaler is used weekly to prevent scale
formation and build up, this will ensure your hot tub is running smoothly.
1. Turn o the hot tub at the mains.
2. Remove the Filter and protective cover.
3. Place your garden hose pipe against the filter inlet hole and outlet holes.
4. Run clean water through the system, helping to remove any debris
or loose limescale.
5. Collect and remove any loose particles from the water, ideally using a net.
6. Follow the instructions for use as directed on the Descaler packaging.
Impeller Blockage/Debris
If a hot tub is used without a filter, or debris has been drawn into the motor
it may cause the impeller within the water pump to seize.
We advise following the below steps to check for problems.
1. Turn o the hot tub at the mains.
2. Drain the water from the hot tub.
3. Remove the filter and protective filter cover.
4. Perform a visual check of the outlet inside and out – check for anything
that maybe obstructing the water flow.
My CleverSpa® is still showing HL and not heating.
If you have tried the above steps and the hot tub still displays the HL error
code it may need to be brought into our service centre for inspection by
a technician.
Please contact our
CleverSpa® Aftersales Team .
[phone] or visit: clevercompany.com.
Check the filter is clean and change if necessary (See Filter
Cleaning Tips). Once this has been checked, press the
‘Filter’ button & the FC Error code will disappear. The water
temperature will be displayed and all the functions will return
to normal.
CODE CAUSE SOLUTION
FC
HL
16

TROUBLESHOOTING
PROBLEMS POTENTIAL CAUSES SOLUTION
A1 Air pump too hot
A2 Air Pump in cooling mode
A3 Possible fault with hot tub motor
A1 Unplug system. After air pump has cooled,
insert plug and press air jets button to activate
A2 Wait for 10 minutes and restart
A3 Call CleverSpa® Aftersales if does not reset
A1 Temperature not locked in
A2 Temperature is not set
A3 Dirty filter cartridge
A4 Improper water levels
A5 Heating element failure
A1 Press temp button again to lock in new temp
A2 Set to a higher temperature (20-40°C)
than current water temperature
A3 Clean/replace filter cartridge
A4 Add water to specified levels
A5 Ask a professional electrician to check household
electrical supply is functioning correctly
A6 Call CleverSpa® Aftersales
A1 Dirty filter cartridge
A2 Filter screwed on too tight
A3 Possible fault with the hot tub motor.
A1 Clean/replace filter cartridge
A2 Loosen the Filter slightly
A3 Call CleverSpa® Aftersales if it does not reset
A1 Insucient filtering time
A2 Dirty filter cartridge
A3 Improper water maintenance
A4 Large particles/debris in water
A1 Increase filtration time
A2 Clean/replace filter cartridge
A3 Refer to chemical manufacturer’s instructions
A4 Remove from water, use suitable tools is needed
A1 CleverSpa®is torn or punctured A1 Use repair patch provided
A2 Check Connectors are fitted correctly
SOME TIPS TO HELP YOU TO DIAGNOSE AND RECTIFY COMMON SOURCES OF TROUBLE:
Air jet system
is not operating
Heating system
does not operate
Filtering system
does not operate /
Rattling noise when
switching filter on
CleverSpa®leaking water
Water not clean
A1 Residual hot water in the element
chamber can cause a higher
temperature to show on the
control panel
A2 Water inlet through filter system
may be blocked
A3 HL code appears
A1 Unplug from mains, wait
30 minutes. Temperature will start
to reduce and return to normal
A2 Clean the inlet
A3 Try HL solutions
Call CleverSpa® Aftersales if does not reset
Display temperature
is higher than 40oC, after
stopping heating function
/ HL Code Displayed
& Beeping
CONTROL PANEL ERROR CODES
An SL Error Code showing on your
CleverSpa® is a low temperature notification.
We can oer guidance to help resolve
the problem.
1. Blocked or dirty Filter.
2. Low Temperature. When the weather
is cold, the SL code may appear. This is
most likely due to the pipe and heater
being too cold to function.
This error code can be easily resolved by:
1. Pouring some hot or warm water into the hot tub (either using
a hot water pipe or buckets of hot/warm water).
2. Pouring some hot water into the top outlet.
A SL Error Code showing on your CleverSpa® Control Panel can
mean there is a blockage in the system which is preventing hot water
from circulating. We can oer guidance to help resolve the problem.
Turn o the hot tub at the MAINS socket, remove the RCD Plug from
the socket, wait 10 seconds, then Plug the RCD Plug back into the
MAINS socket.
Remember: Sun cream, fake tan & soap etc can force the filter to
work much harder.
After cleaning your filter does your CleverSpa® still not heat?
Have you tried replacing your filter with a new one?
Also, have you ensured that your filter is not screwed on too tightly?
CODE CAUSE SOLUTION
SL
17
If the SH Error code appears on your
control panel, this is a system failure.
Please contact the CleverSpa® Aftersales Team so that we can
arrange to collect your hot tub to fully inspect it on:
[phone] or visit: clevercompany.com.
SH

WARRANTY
18
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other household waste throughout the EU. To prevent possible harm to the
environment, or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.
To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can
take this product for environmental safe recycling.
STANDARD WARRANTY
Warranty relates to all CleverSpa®hot tubs bought
in UK and covers the following areas:
• CleverSpa® Pump Heater:
12 months from date of purchase
• CleverSpa® Cover & Liner:
6 months from date of purchase
Warranty is not transferable if the goods are resold
after original purchase. CleverSpa®is designed and
manufactured for domestic use only. The Warranty
does not extend to any commercial businesses use.
FREE EXTENDED WARRANTY
If you register within 28 days of purchase we will
extend your warranty to:
• CleverSpa®Pump Heater:
18 months from date of purchase
• CleverSpa®Cover & Liner:
9 months from date of purchase
REGISTERING YOUR WARRANTY
Visit clevercompany.com/support/warranty
and complete the form within 28 days of purchase
Warranty will start from date of purchase which must
be verified by proof of purchase.
WARRANTY CLAIMS
Before making a claim, please visit
clevercompany.com/support/cleverspa-faqs
for up-to-date troubleshooting advice and
technical information.
If this does not solve the issue and you need to make
a claim, visit our website under warranty section,
or contact Aftersales Team by email at:
[e-mail]
Please note: All CleverSpa® warranties are void if
the product has been subject to repair attempts not
authorised by CleverSpa®, including, but not limited
to removal of the motor from the liner and opening
or tampering with the motor casing.
CONTACT US
Before contacting the CleverSpa® Aftersales Team, please ensure that
you have registered your warranty using our online form.
Once completed please include:-
• Your Warranty ID
• CleverSpa® Model
• CleverSpa® Retail Partner
• Photo(s) of the Hot Tub Set-up
• Photo of the Batch Code (located on the motor to the bottom right of the legal panel)
• Photo(s) or Video(s) showing any of the issues youmay experiencing
This will help our team to resolve your problem as quickly as possible.
If you need to make immediate contact, our Aftersales Team are available on:-
By Phone: [phone]
By Email: [e-mail]
SCAN ME TO
GO TO OUR
WARRANTY
REGISTRATION
WEBPAGE

RETURNS
NEED TO RETURN YOUR CLEVERSPA®?
PLEASE FOLLOW INSTRUCTIONS BELOW:
Keep receipt(s) or order number safe, you will need
it as proof of purchase in event of aftersales queries.
• Purchased from a UK retailer: Call CleverSpa®
Aftersales Team. This will require proof of purchase
and completion of warranty registration.
• Purchased from clevercompany.com: If purchased
directly from our website, contact us and we will
email instructions to return the product.
Contact can be made by email or telephone -
see warranty claims section.
• Changed your mind/Order Cancellation
Under Distance Selling Regulations, as a consumer
you have the right to cancel your order and return
goods unused, provided we are notified within a
period of 14 days after delivery of goods.
This will require the product to be unopened and
unused. Please contact us & we will send instructions
to return the product. When posting items back, clearly
mark parcel with order number and full name. You are
responsible for shipping products back to us and will
be required to pay the cost of returning the item to
us. Please use a traceable shipping method. Individual
products may be excluded from this guarantee. Check
product description before you place orders.
POINTS TO NOTE:
• Under Distance Selling Regulations, as a consumer
you have the right to cancel your order
and return goods unused if we are notified within a
period of 14 days after delivery of goods.
• You are responsible for shipping products back to
us. Use a traceable shipping method.
• If you choose to cancel your order, we require you,
the consumer, to pay the cost of returning
the item to us.
• Individual products may be excluded from this
guarantee. Check product description before
you place orders.
• We can’t take responsibility for any missing or
damaged parcels - take care when returning
orders to us.
DEFECTIVE ITEM/REFUND
For any troubleshooting tips, visit the FAQ section
of clevercompany.com
If return is due to a product defect, contact
Clever Company for assistance. Email us:
[e-mail] or call
[phone].
Prior to contacting us, please ensure:
1. You have registered your warranty (see page 16).
2. You include any photo/video evidence, as this
will ensure that your problem is resolved quicker.
INCORRECT ITEM SENT
Contact Clever Company and provide an image of the
incorrect item. The Service Agent will arrange for the
correct item to be sent out and arrange for the return
of the incorrect item.
DAMAGED ITEMS
Purchased from a UK Retailer: If you’ve purchased
from a UK retailer and received a damaged item please
follow the retailers instructions for returns.
Purchased from Clever Company Website: If you
have purchased from the Clever Company Website
and found the product to be damaged after delivery
please contact us to arrange for the return .
Damaged in transit: If you receive an order with
obvious shipping damage purchased from either the
Clever Company website or a CleverSpa retailer, we
suggest the delivery is refused.
If you have accepted delivery and then find shipping
damage, please call the courier immediately using the
contact information included with the order. Keep all
packaging. If you dispose of packaging material or
attempt to return the merchandise without contacting
the courier, you jeopardise your chances of making a
claim, and you may not receive a credit for the return.
LIMITS OF RESPONSIBILITY
Clever Company accepts no responsibility for user
error, misuse, damage or loss of parts incurred during
operation or use of a product. Examples of misuse or
user damage include a puncture, fire e.g.. Smoking
or BBQs, use of incorrect voltage, a socket that is
not suitable, well maintained or waterproof, use of an
extension cable, excessive exposure to environmental
elements e.g.. very hot weather or extreme cold
spells, installing over inappropriate surfaces, rewiring
the electrics, direct sunlight, over inflation, lack of
maintenance, or not storing the hot tub away properly,
incurring mould build up and other faults.
19

Clever Company Ltd.
UK Address: Oldgate, St.Michael’s Industrial Estate, Widnes, Cheshire, WA8 8TL.
European Address: Radarweg 29, 1043 NX Amsterdam, Netherlands.
General Enquiries, Returns, Spare Parts, Repairs & Chemical Advice
[phone] or visit: clevercompany.com
HELPFUL CLEVERSPA®QR CODES
Scan the below for helpful setup videos to FAQS
CHEMICAL SHOCK TREATMENT WHEN
USING HOT TUB FOR THE FIRST TIME
CHECK OUT THESE HANDY
FILTER CLEANING TIPS
WATCH THE CLEVERLINK® APP
VIDEO
FOLLOW US ON
INSTAGRAM
FOLLOW US ON
FACEBOOK
HOW TO SET-UP AND INFLATE
YOUR CLEVERSPA®HOT TUB
HOW TO CHANGE THE FILTER
IN A CLEVERSPA® HOT TUB
HOW TO SET-UP THE TEMPERATURE
OF YOUR CLEVERSPA® HOT TUB
HOW TO EMPTY YOUR
CLEVERSPA® HOT TUB
HOW TO PACK AWAY YOUR
CLEVERSPA® HOT TUB
LEARN ALL ABOUT CLEVERSPA®
INFLATABLE HOT TUBS