Climate Caddy FORE AIRE SCC7701 Manual

Rooftop Fan System
For 12v Gas-Powered Club Car Precedent Carts
& 48v Club Car Precedent Carts
Installation Instructions & User Manual
Thank you for choosing Climate Caddy for your cart heating and cooling needs! By purchasing a Climate Caddy product,
you have received new, patent pending technology that we hope you will love. We truly appreciate your business! Please let us
know if we can help in any way. Your feedback is important to us as we constantly look for ways to improve our products.
Best Regards, Climate Caddy Team
844-233-4121
Climatecaddy.com
[email protected]
809 110th Ste 151
Arlington, TX 76011
P/N: II-800-5
Rev. 3
06/26/2020

Fore Aire - 12v/48v Club Car Precedent - Installation Instructions__ ________
1
IMPORTANT SAFETY INFORMATION
The 12v Fore Aire is currently made to be used on 12v gas-
powered golf carts only. Do not attempt to hookup to a non-
12v cart as damage to the unit may occur.
The 48v Fore Aire is made to be used on a 48v golf cart
only. Do not attempt to hookup to a non-48v cart as damage
to the unit may occur.
Only operate the Fore Aire while the unit is securely
installed on the vehicle.
Do not block the Fore Aire intake around the Dome and
maintain at least a 3” clearance.
Do not operate Fore Aire in the rain.
Do not operate Fore Aire with a Golf Cart enclosure
covering the Dome.
Possibility of personal injury when working on high voltage
electrical circuitry and batteries. Use best safe practices and
remove jewelry before hooking up to the battery to make
sure that metal jewelry such as bracelets and rings do not
come in contact with battery terminals and cause shorting.
Shorting across battery terminals may cause explosion.
FORE AIRE FEATURES OVERVIEW
Electronic Eyes (48v only)
Prevent unnecessary battery drain as the FORE AIRE only
operates when passengers are detected.
Air flow Control Knob
From a gentle breeze to a powerful blast of refreshing air.
Energy Management
Using soft start technology, Fore Aire prevents the excessive
drain of traditional electric fans.
360° rotating vents
Direct the air precisely where you need it. You can also
close the vents completely to keep cold air out.
Cosmetic Adapter
Fits the most popular E-Z-GO, Yamaha, and Club car roof
models that give an integrated OEM look.
Ultra-Bright LED Lighting
Two sets of LED lights on the front and rear of the Fore Aire
for increased visibility.

Fore Aire - 12v/48v Club Car Precedent - Installation Instructions__ ________
2
Before you begin, read these instructions twice and check to be sure all
parts and tools are accounted for. Please retain these installation
instructions for future reference and part ordering information.
Suggested Tools:
• Variable Speed Jig Saw
• 11 to 14 TPI Saw Blade
• Sawhorses
• Drill Motor
•Drill Bit Sizes: (1/16”) (1/2”) (1/4”) (3/8”) (5/8”)
• Torx Bit Sizes: (T10) (T27) (T40)
• Marker
• Tape Measure
• 7/16” Wrench
• 7/16” Socket
• Flat HD Screwdriver
• Phillips HD Screwdriver
• Deburring Tool
This Kit includes:
A
1
Dome
B
1
Base
C1
1
Roof Adapter MP701-58
C2
1
Roof Adapter MP701-62
C3
1
Roof Adapter MP701-60
D
1
Control Panel
E
4
Vents
G
1
Wiring Harness HA-C58
H
1
Saw Guide
I
1
Mounting Plate
J
10
Cable Ties
K
4
#8 x 1” Phillips Pan HD Screw
L
10
#8 x 5/8” Phillips Pan HD Screw
M
2
#8-32 x 5/8” Phillips Pan HD Screw
N
2
Lock Nut
O
4
#8 x 7/8” Phillips Pan HD Screw
P
2
#8 x 1/2" Phillips Oval HD Screw
Q
4
#8 x 5/8” Phillips Oval HD Screw
R
1
Harness Adapter HA-C55
S
1
Harness Adapter HA-C54

Fore Aire - 12v/48v Club Car Precedent - Installation Instructions__ ________
3

Fore Aire - 12v/48v Club Car Precedent - Installation Instructions__ ________
4
1. Roof Modifications
a. Harness Center Hole
i. Remove the Golf Cart Roof and place it onto
sawhorses with the underside facing up.
ii. Measure and mark 9” from the edge and 1 ¼” from
the bottom as shown. (Figure 2)
iii.Drill a hole at the mark using a 1/2” drill bit.
b. Harness Access Hole
i. Using a 5/8” drill bit,
drill the harness access
hole into passenger
side roof support area
approximately as
shown. (Figure 3)
Figure 1
Figure 2
Figure 3

Fore Aire - 12v/48v Club Car Precedent - Installation Instructions__ ________
5
Main Mounting Hole
i. Measure and mark a line 15 1/4” from the roof rear
angle as shown. (Figure 4)
ii. Place Adapter (C2) onto the roof as shown and align
the adapter edge with your mark. (Figure 5)
iii. Using Adapter (C2) as a guide, drill a 1/4” pilot hole
through the roof. Remove Adapter (C2) and set aside.
iv. Flip the roof over and drop the Saw Guide (H) center
pin into the pilot hole, being careful to rotate and align
to the roof front and back as indicated on the guide.
(Figure 6)
v. Once aligned, secure the Saw Guide with screw
(L) in three places.
vi. Drill a 1/16” diameter
pilot hole at the Saw
Guide notches in four
places. The drill bit
should fit into the notch
as shown. (Figure 7)
vii. Remove the Saw Guide and enlarge the four pilot
holes to 3/8” dia. These will be your starter holes for
the saw blade.
Figure 4
Figure 5
Figure 6
Figure 7

Fore Aire - 12v/48v Club Car Precedent - Installation Instructions__ ________
6
viii. Replace the Saw Guide and secure it with the three
screws into the original holes.
ix. Using the Jig Saw on a low speed setting, begin
cutting at the Saw Guide notches, taking care to stay
within the slots and stopping just before you reach the
slot end.
x. Repeat this for all four slots and then remove the Saw
Guide. Save the three screws for step 2F.
xi. Carefully cut the four remaining segments and use a
deburring tool to clean up the hole edges as needed.
(Figure 8)
xii. Flip the roof over so the underside faces up.
2. Fan Installation
a. Remove the adhesive backings from the Mounting Plate
(I) and set it on the roof underside so that it aligns with
the Main Mounting Hole. (Figure 9)
b. Using the plate as a guide, drill pilot holes through the
Mounting Plate in 8 places with a 1/16” drill bit.
(Figure 9)
c. Flip the roof over to the upright position.
d. Remove adhesive backing from Base (B).
e. Drop the power connecter through and lower the Base
into the Main Mounting Hole while taking care not to
damage the roof seal gasket. Ensure proper orientation as
per Figure 10.
Figure 8
Figure 9

Fore Aire - 12v/48v Club Car Precedent - Installation Instructions__ ________
7
f. Secure Base (B) with Screw (L) in ten places, into the
previously drilled pilot holes (step 2b).
g. Install Dome (A) with Screw (K) in four places.
h. Flip the roof over so the underside faces up.
i. Feed the power cable through the Harness Center Hole.
(Figure 11)
j. Set Adapter (C2) onto the roof and slide into position
over the wiring harness. (Figure 12)
k. Set Adapter (C3) onto the roof and slide into position as
shown. Secure with Screw (M) and Lock Nut (N) into the
rear holes in 2 places. Slide Adapter (C2) rearward until
the two holes line up with Adapter (C3) and secure with
screw (P) 2 places. (Figure 13)
Figure 10
Figure 11
Figure 12
Figure 13

Fore Aire - 12v/48v Club Car Precedent - Installation Instructions__ ________
8
l. Set Adapter (C1) over the Fore Aire base and align with
the mounting plate. Secure with screw (O) in four places.
(Figure 14)
m. Install the Control Panel (D) to the Base (B) while
plugging in all connectors to the matching color
marked holes. (Figure 16)
n. Secure the control panel to Adapter (C1) using screw
(Q) in 4 places.
o. Insert Vents (E) into the control panel in four places.
Press down on the vents until they snap into place.
(Figure 17)
Figure 14
Figure 16
Figure 17

Fore Aire - 12v/48v Club Car Precedent - Installation Instructions__ ________
9
3. Wiring Harness
a. Remove the golf cart seat and set aside.
b. Remove
the rear battery
compartment
panel by gently
prying the pins
with a Flat HD
screwdriver in 2
places. (Figure
18)
c. Drop a fish line down into the
rear passenger side roof support
(Figure 19) so that it enters the
rear battery compartment as
shown. (Figure 20)
d. Run the Wiring Harness (G) power connecter from the
battery compartment, behind seat as shown. Tape the
power connector to the fishline and gently pull it
through so that it exits the roof support. (Figure 20)
e. Remove floor mat as shown. (Figure 21)
Figure 20
Figure 21
Figure 18
Figure 19

Fore Aire - 12v/48v Club Car Precedent - Installation Instructions__ ________
10
f. Remove base board as shown. (Figures 22a (12v)/(48v),
22b, 22c)
g. Detach dash panel as shown and let hang in place
(Figures 23, 26)
Figure 22a (12v)
Figure 22c
Figure 22b
Figure 22a (48v)

Fore Aire - 12v/48v Club Car Precedent - Installation Instructions__ ________
11
h. Connect Harness Adapter HA-54 (S) to the matching
connector on the Wiring Harness (G). Run the Harness
Adapter so that it exits the battery compartment through
the opening as shown. (Figure 24 (12v)/(48v))
i. Run the Harness Adapter (S) from the battery
compartment to the vehicle dash through the floor
channel as shown. (Figures 22b, 25)
Figure 24 (12v)
Figure 25
Figure 23
Figure 24 (48v)

Fore Aire - 12v/48v Club Car Precedent - Installation Instructions__ ________
12
j. Connect the Harness Adapter (S) to the key switch as
shown. (Figure 27)
k. Replace the golf cart roof and connect the harness
power connector as shown, through the harness access
hole. (Figure 28)
4. Finalize Installation
a. 12v: Connect the red wiring harness cable to the
positive battery terminal and the black wiring harness
cable to the 12v negative battery terminal. Check Fore
Aire system operation.
48v: Attach the red wire to the 48v output terminal
having a red ground output terminal having a black
wire leading away from the battery pack. Check Fore
Aire system operation. (Figure 29 (48v))
Figure 26
Figure 27
Figure 28

Fore Aire - 12v/48v Club Car Precedent - Installation Instructions__ ________
13
Note: Pictures may not match actual battery configuration. Always
confirm correct terminals before hooking up the Fore Aire
b. Replace the dash panel, floor mat, baseboard, and rear
battery compartment panel.
c. Secure fuse and dress wires in battery compartment with
cable ties. Replace the seat.
Congratulations, the installation is complete!
Troubleshooting
Problem: Unit will not power on.
Cause 1: The Fore Aire needs to be reset.
Solution: Reset the Fore Aire by turning the cart key-switch to the off
position while ensuring the Fore Aire is set to mode 1 (off). Once both
are off, turn the key-switch on first, then power-on the Fore Aire.
Cause 2: Inadequate power connection.
Solution: Ensure proper harness connections, including the power
connector, harness adapter, and switched power connection.
Cause 3: Inadequate battery connection.
Solution: Check battery terminals to ensure a clean, proper connection
to the positive and negative terminals.
Cause 4: Improper switched power connection.
Solution: Using a volt/ohm meter, ensure a proper 12v or 48v
connection when cart key is turned off/on.
Cause 5: Battery fail-safe sensor
Solution: Recharge the cart batteries. The fail-safe sensor will
automatically shut the Fore Aire off when battery voltage drops below a
preset threshold.
Problem: Electronic Eyes will not power off the fans.
Solution: Ensure there are no objects in path of the Electronic Eye beam.
Any objects left on or around the seat could fool the Fore Aire into
thinking a passenger is present.
Figure 29 (48v)

Fore Aire - 12v/48v Club Car Precedent - Installation Instructions__ ________
14
Fore Aire Operation
Electronic Eyes (48v only)
The Fore Aire is equipped with two pairs of fans that operate independently
based on Electronic Eye detection of cart occupants. When the driver is
present, only the driver-side fans will engage, which is the same for the
passenger side.
Battery Fail-Safe Sensor
5-Mode Fan Speed Control Knob
To power on the Fore Aire, turn on the golf cart key switch and then turn the
Fan Speed Control knob from the off position to the desired
mode. The LED Indicator will light up when the Fore Aire
is powered on.
1- Off
2- Low Speed
3- Medium Speed
4- High Speed
5- Turbo mode*
* When Turbo mode is engaged, all four fans will spin at maximum speed and
use both driver and passenger electronic eyes for detection.
Ultra-Bright LED Lighting
Can be toggled on and off by pressing the square button located
between the LEDs. Only the golf cart key switch needs to be on for
the lights to function.

Fore Aire - 12v/48v Club Car Precedent - Installation Instructions__ ________
15
Climate Caddy Two-Year Limited Warranty
TSI Products, Inc./Climate Caddy Products are warranted to the
original retail purchaser, to be free from defects in materials and
workmanship except as otherwise provided herein. This warranty is
not transferrable and is effective from the date of the original
purchase date.
This Warranty Covers:
1. During the first year from the original retail purchase date, TSI
Products/Climate Caddy will, at its option repair or replace
defective components, including labor and cost of shipment to
original consumer.
2. After the first year from original retail purchase date, up to the term
of the warranty, TSI Products/Climate Caddy will repair or replace
defective components with an identical or reasonably equivalent
new component for a $5000 service charge which includes labor
and cost of shipment to the original consumer.
The Warranty Does Not Cover:
1. Cost of shipping the product to TSI Products/Climate Caddy.
2. Normal wear, scratches or fading of the product.
3. Damage caused by abuse, misuse, neglecting to follow use
procedures, failure to follow installation procedures (See
instructions in product package) or product modifications made by
consumer.
4. Damage to home or vehicle electrical system or components
cause by inadequate wiring to the product plug-in point.
5. Damage to any object placed close (see instructions on product
package) to the air output of the heater.
6. Damage caused by dropping of heater.
7. Product sold outside the USA.
8. Consequential damages, incidental damages or expenses,
including damages to property. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you.
Procedures for Warranty service:
1. Contact TSI Products/Climate Caddy (844-233-4121) for a return
authorization number. Write this number on the carton being
returned to TSI Products/Climate Caddy.
2. Attach, to the product itself, a tag showing your name, address,
phone number, description of the problem and proof of retail
purchase date. Enclose a cashier’s check, check, Visa or
MasterCard information or money order for applicable service
charges.
3. Package the product carefully to ensure that no damage occurs
during return shipment. Return the product, postage prepaid, to
TSI Products/Climate Caddy.
Implied Warranty:
This warranty is limited to the provisions clearly stated herein. Any
implied warranties, warranties of merchantability, warranties of fitness
for a particular use are excluded.
If any provision of this warranty is prohibited by federal, state, or local
law, that provision shall not be applicable.