Clinton Electronics IDX Series User manual

1. INSTALL MOUNTING PLATE
Secure the Mounting Plate to a compatible conduit box (Single Gang, Double Gang, 3-1/4" & 3-1/2", or 4"
Oct/Rd) using the screws that came with the conduit box, or mount to a solid surface using the 4 screws
included with this camera.
*Information in this document
is subject to change without notice
v.05.27.15
clintonelectronics | 6701 Clinton Road Loves Park, IL 61111 | 800.447.3306 (Sales) | 800.549.6393 (Support) | www.clintonelectronics.com
3. CONNECT CABLES
Make connections to the BNC cable and the power connection. Feed any cable slack into the mounting
surface. A green LED (near the OSD Joystick and DIN Connection Port) will light up on the circuit board
when the camera is receiving power. To ensure quality operation, verify proper BNC and power termina-
tion, along with proper voltage at camera.
NOTE: It is recommend to use drywall anchors if mounting to drywall. Drywall anchors not included.
IDX Series [IR] Install Guide
For IR LED Equipped Cameras: IDX18(B) • IDX30(B) • IDX50(B)
2. REMOVE DOME COVER
Hold the dome cover with one hand while gripping the finger grip tabs on the bottom of the camera base.
Turn the finger grip tabs (camera base) counter-clockwise to separate it from the dome cover.
4. ATTACH CAMERA TO MOUNTING PLATE
Attach the camera to the mounting plate by aligning the hooks on the mounting plate to the tabs on the
camera base. Twist the camera base clockwise to lock it in place.
• IDX Series Camera x 1
• Mounting Plate x 1
• 4x20mm Screws x 4
• Instructions x 1
• Test Monitor BNC Lead x 1
FINGER GRIPS
Included Items:
• Phillips Head Screwdriver or Drill with Phillips Head Bit
Required Items:
• CE-REMOTE (OSD Remote Control)
Optional Items:
TO CAMERA
VIDEO
CONNECTION
POWER
CONNECTION
TO DVR
OR
MONITOR
ALIGN
CAMERA BASE MOUNTING PLATE
HOOK
GREEN LED
POWER INDICATOR

TEST MONITOR
BNC LEAD
CN2
J1
SW1
*Information in this document
is subject to change without notice
v.05.27.15
clintonelectronics | 6701 Clinton Road Loves Park, IL 61111 | 800.447.3306 (Sales) | 800.549.6393 (Support) | www.clintonelectronics.com
5. CAMERA ANGLE ADJUSTMENT
6. ZOOM / FOCUS ADJUSTMENT
Adjust the angle of the camera as necessary. It is recommended to test the operation and intensity of the
IR LEDS. To test, cover the IR Sensor and verify that the IR LEDs turned ‘ON’. To adjust the intensity of the
IR LEDs, use a Phillips head screwdriver to turn the IR level adjustment potentiometer, (located next to the
OSD Joystick on the board). Turn the screw to the RIGHT (clockwise) for brighter LEDs or to the LEFT
(counter-clockwise) for dimmer LEDs.
7. TEST MONITOR / OSD CONTROL
To test the camera with a test monitor use either the supplied Test Monitor BNC Lead or optional
CE-REMOTE. The Test Monitor BNC Lead plugs into the small, 2 PIN connector (marked CN2) next to the
wide 12 wire connection on the circuit board. The CE-REMOTE plugs into the DIN Port. OSD Adjustment
can be made by using the OSD Joystick or the optional CE-REMOTE. Refer to OSD Manual for detailed
instructions on adjusting camera settings.
8. REPLACE DOME COVER
Carefully replace the dome cover onto the camera assembly by twisting the dome cover clockwise to lock
into place. Make sure the IR Sensor is free from obstruction and will not be covered by the dome cover
once it is re-attached. If the sensor is covered it will cause the IR LEDs to be on all the time.
CE-REMOTE
*sold separately
A. Lens Rotation: Rotate the
U-Bracket on the gimbal to
adjust.
B. Lens Angle: Loosen thumb
screws on each side to adjust
the tilt of the lens.
C. Camera Plate Rotation:
Pinch the gimbal U-Bracket
and rotate the camera
assembly on the base.
Loosen the appropriate adjustment lever by turning counter-clockwise. To widen the viewing angle, rotate
the Zoom lever to the Left. To narrow the viewing angle rotate the ZOOM lever to the Right. Rotate the
Focus lever Left or Right to focus the lens.
ZOOM
FOCUS
After zoom / focus adjustments have been made, tighten the adjustment levers to lock the adjustments.
DIN PORT
OSD
JOYSTICK
IR POTENTIOMETER
IR SENSOR
IR SENSOR LOCATION
RIGHT
WRONG
U-BRACKET
THUMB SCREW