CloudWalker BURST I2000 User manual

BÜRST I2000
User Manual
Design and Specifications are subjected to change w ithout prior notice.
品号
32280100901001

WARNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
WARNING: USE UNDER SUPERVISION OF AN ADULT DUE TO LONG
CORD This unit has a long cord that can be easily tripped on or pulled on,
causing injury. Please make sure it is arranged so that it will not drape over a
tabletop, etc. Where it can be pulled on by children or tripped over accidentally.
CAUTION: TO REDUCE THE ELECTRIC SHOCK, DO NOT REMOVE THE
COVER (OR BACK). NO USER SERVICEABLE PART INSIDE, REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DANGEROUS VOLTAGE:The lighting flash with arrowhead symbol within
an equilateral triangle is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure that may
ATTENTION:The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
2
1. Read these instructions
All the safety and operating instructions should be read before the appliance is
operated.
2. Keep these instructions
The safety and operating instructions should be kept for future reference.
3. Heed all warnings
All warnings on the appliance and in the operating instructions should be
adhered to.
4. Follow all instructions
All operation and use instructions should be followed.
5. Do not use this apparatus near water
The appliance should not be used near water; for example, near a bath tub,
be of sufficient magnitude to constitute a risk of electric shock to persons.
Before using the unit, be sure to read all operating instructions carefully, please
note that these are general precautions.

washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming
pool.
6. Clean only with dry cloth
The appliance should be cleaned only as recommended by the manufacturer.
7. Do not block any ventilation openings.Install in accordance with the
manufacturer’s instructions.
Slots and openings in the cabinet and in the back or bottom are provided for
ventilation, to ensure reliable operation of the product and to protect it from
overheating. These openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed, sofa, rug, or similar
surface. This product should never be placed near or over a radiator or heat
source. This product should not be placed in a built-in installation, such as a
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
10. Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments / accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury
from tip-over.
An appliance and cart combination should be moved with care. Quick stop,
combination to overturn.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or
3
bookcase or rack unless proper ventilation is provided or the manufacturer's
instructions have been adhered to.
excessive force and uneven surfaces may cause the appliance and cart
9. Do not defeat the safety purpose of the grounding-type plug. A
grounding type plug has two prongs and a third grounding prong. The
third prong is provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete
outlet.
To protect your product from a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet. This will prevent
damage to the product due to lightning and power-line surges.

moisture, does not operate normally, or has been dropped.
15. Power source
This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to your
home, consult your appliance dealer or local power company. For products
intended to operate from battery power, or other source, refer to the operation
instructions.
16. Power lines
An outside antenna system should not be located in the vicinity of overhead
power lines or other electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power lines or circuits as
contact with them might be fatal.
17. Overloading
Do not overload wall outlets and extension cords as this can result in a risk of
fire or electric shock.
18. Object and liquid entry
Never push objects of any kind into the product through openings as they may
touch dangerous voltage points or short out parts that could result in fire or
electric shock. Never spill or spray any type of liquid on the product.
4
19.
20.
Service
Do not attempt to service this product yourself as opening or removing covers
may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
When replacement parts are required, be sure the service technician uses
replacement parts specified by the manufacturer or those that have the same
characteristics as the original parts. Unauthorized substitutions may result in
fire or electric shock or other hazards.
21.
Replacement parts
Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper
operating condition.
2 . Wall or ceiling mounting
The product should be mounted to a wall or ceiling only as recommended by
the manufacturer.
Safety check
2

b)If liquid has been spilled or objects have fallen into the product.
c)If the product has been exposed to rain or water.
d)If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating
instructions, as an adjustment of other controls may result in damage and will
require extensive work by a qualified technician to restore the product to its
normal operation.
e)If the product has been dropped or the cabinet has been damaged.
f)When the product exhibits a distinct change in performance- this indicates a
need for service.
Unplug this product from the wall outlet and refer service to qualified service
personnel under the following conditions.
a)When the power- supply cord or plug is damaged.
5
3
2 . Damage requiring service

PROdUCT OvERvIEW
6
11. Power Cable
CONTROL PANEL
FRONT VIEW
BOTTOM VIEW 3
REAR PANEL
12
VOL - VO L+ PLAY /
PAUS E
STAN DB Y
/SO UR CE
4 5 6 7 8 9 10 11
AUX IN
OPTI CAL IN LINE I N
L R AC IN
110V-2 40V
SOUNDBAR
2. Remote Sensor
1. Source Indicator
3. LED Light Effect
4. Volume Down
5. Volume Up
6. Play/Pause
7. Standby/Source
9. OPTICAL IN
8. AUX IN
10. LINE IN

BATTERY INSTALLATION OF REMOTE CONTROL
Fig.1
Fig.2 Fig.3
Remove and discard the insulation film as Fig.1.
Replacing battery for Remote Control
First time use
7
REMOTE CONTROL
OPEN
OPEN
3V CR2025
3V CR2025
1. Pull out the battery holder as indicated in Fig.2.
2. Replace the old button cell with a new CR2025 button cell
with the polarity markings facing upward as Fig.3.
3. Push back the battery holder as Fig.4.
Fig.4
1
2
3
5
7
8
9
10
12
1. Power On/Off
6. AUX
15. LINE IN
4. Previous
7. Mute
10. Next
11. Play/Pause
9. Volume Up/Down
12. Bluetooth
5. OPTICAL
8. Light Effect
11
13
OPTICAL
EQ
LINE
IN
AUX
BT
Pair
BASS TREBLE VOL
615
14
4
2. Bass Up/Down
3. Treble Up/Down
13. Bluetooth pair
14. EQ

9
8
3. Do not mix different types of batteries together ( e.g: Alkaline and Carbon -zinc )
or old batteries with fresh ones.
4. If the batteries in the device are consumed or the device is not to be used for a long period of time,
remove the batteries to prevent damage or injury from possible leakage.
5. Do not try to recharge the battery as it is not intended to be recharged; it can overheat and rupture.
(Follow the battery manufacturer’s instructions.)
6. The batteries shall not be exposed to excessive heat such as sunshine or fire.
7. Clean the battery contacts and also those of the device prior to battery installation.
8. The remote control is supplied with a coin/button
cell battery. If the coin button cell battery is
swallowed, it can cause severe internal burns in
just 2 hours and can lead to death. Keep new
and used battery away from children. If the
CR2025
Remote control operation range
●
●When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light
shines on the REMOTE SENSOR of the unit, the operation of the remote may be unstable.
CAUTION
●Danger of explosion if the battery is incorrectly replaced.
●Replace only with the same or equivalent type.
16.4 Feet (5M)
When there is an obstacle between the transmitter and the unit, the unit may not operate.
OPTI CAL
EQ
LINE
IN
AUX
BT
Pair
BASS TREBLE VOL
BATTERY PRECAUTIONS
Follow these precautions when using a battery in this device:
1. Use only the size and type of battery specified.
2. Be sure to follow the correct polarity when installing the battery as indicated in the battery
compartment, a reversed battery may cause damage to the device.
stop using the product and keep it away from
children. If you think batteries might have been
swallowed or placed any part of the body, seek
immediate medical attention.
battery compartment does not close securely,

PLACEMENT AND MOUNTING
1. Placing the device on a table - Ventilation
2. The Installation Distance
9
2-3inches
2-3inches
921mm(36.2 inches)
When placing the soundbar on an entertainment center, bookshelf, or any type of
space, be sure to allow enough space for ventilation.
Otherwise, the heat generated will produce potential heat hazard.
SOUNDBAR

2.1 Mountingto a wooden wall
A. Mark the position of the mounting screws on the wall using a pencil.
C. Put the sound bar onto the mounting screws. Make sure they are firm and stable.
2.2 Mountingto a brick wall
36.2 inches
B. Drill the screws directly into the marks that you have made on the wall and leave
approx. 0.3 inches length to hook the sound bar.
(screws not included)
(screws and plastic fixing plug are not included)
A. Mark the position of the mounting screws on the wall using a pencil.
E. Put the sound bar onto the mounting screws. Make sure they are firm and stable.
C. Insert the fixing plug and hammer into the holes.
D. Secure the screws into the fixing plug and leave approx. 0.3 inches length to hook
the sound bar.
B. Drill 2 holes on wall with a powerful electric drill.
36.2 inches
10

GENERAL OPERATION
11
4. During Playing:
2. Press and hold the Standby/Source button on the soundbar or press button on
remote control to power on the soundbar. The LED light effect will light up.
remote control repeatedly to adjust volume.
Press the VOL-/+ button on the soundbar or the VOL up and down button on the
Press the EQ button on remote control to set to desired EQ mode.
Press the Bass up or down button on remote control to set to desired bass level.
Press the Treble up or down button on remote control to set to desired treble level.
Press the button on remote control to turn off sound, the source indicator on
1. Connect the AC plug to the AC outlet. The source indicator on the soundbar will
turn red.
3. Press the Standby/Source button on
Or press the AUX, OPTICAL,
Blue.............................................................................................Bluetooth Mode
Green.............................................................................................AUX IN Mode
, LINE IN,
on front of the soundbar will turn to:
Violet (red+blue)............................................................................LINE IN Mode
Indigo (blue+green)................................................................OPTICAL IN Mode
the soundbar repeatedly to switch to desired
mode. button on remote control for
desired mode, the indicator
the soundbar will blink, press this button again to unmute.

GENERAL OPERATION
12
light effects.
Mode 1: The LED light will be solid Blue.
Mode 2: The LED light will be solid Green.
Mode 3: The LED light will be solid Red.
Mode 4: The LED light will be Yellow.
Mode 5: The LED light will be Sky Blue.
Mode 6: The LED light will be Violet.
Mode 7: The LED light will be White.
Press the button on remote control repeatedly to change to different LED
5. Press and hold the Standby/Source button on the soundbar or press button on
remote control to power off the soundbar.
light effect.
Press and hold the button on remote control to turn on or turn off the LED
Mode 10: The LED light flashes in disco mode.
Mode 11: The Blue, Violet, Red, Yellow, Green and Sky Blue Light effect will
go from left to right slowly and repeatedly.
Mode 9: The LED light with combined color will flash repeatedly and
alternatively.
Mode 8: The LED light w ill go from left to right according to the music rhy thm.

BLUETOOTH OPERATION
10
4. After successful paired, the indicator will be solid blue.
13
connection, then you can pair to new devices with this sound bar.
6. Press and hold the BT Pair button on remote control to disconnect current
2. Power on external Bluetooth enabled device and enter Bluetooth mode and try
searching the soundbar.
mode, the indicator on front of soundbar will turn Blue and blink.
3. When appears, select it and make connection.
turns blue, or press the button on remote control to switch to the Bluetooth
1. Press the Standby/Source button on the soundbar repeatedly until the indicator
CloudWalker BÜRST
function are activated and they are in working range.
device if their Bluetooth
NOTE:
The soundbar will be automatically connected with the last connected Bluetooth
5. During playing:
Press the or button on remote control to skip tracks.
Press the button on remote control to pause, press it again to resume.
Or Press the PLAY/PAUSE button on soundbar to pause, press it again to
resume.

AUX IN OPERATION
14
An external Audio player(such as mobile phone, MP3 player etc.) can be connected
to this soundbar and listen through the speakers.
Rear View
Mobile Phone
MP3 Player
1. Plug one end of the AUX IN cable into the AUX IN jack on the soundbar.
2. Plug another end of the AUX IN cable into the headphone jack or AUX OUT jack
on the external audio player.
AUX IN
OPTICAL IN LINE IN
L R AC IN
110V-240V
Connect to AUX OUT jack or LINE OUT jack
of other compatible devices like mobile phones,
MP3 players etc.
..............................................................................
...................................
..............................................................................
...................................
4. Power on the connected external player and start playing.
AUX on remote control to switch to the AUX IN mode,
3. Press the Standby/Source button on the soundbar repeatedly or press the AUX
the indicator on front of
the soundbar will turn Green.

LINE IN OPERATION
An external Audio/Video device(such as Set-Top Box, DVD player etc.) can be
15
connected to this soundbar and listen through the speakers.
1. Plug one end of the LINE IN cable into the LINE IN jack(L&R) on soundbar.
2. Plug the other end of the LINE IN cable into the LINE OUT jack(L&R) on Set-Top
Box or DVD player etc.
LINE OUT jack of Set-Top Box
/DVD player etc.
L R
white
red
Rear View
AUX IN
OPTICAL IN LINE IN
L R AC IN
110V-240V
LINE IN button on remote control to switch to the LINE IN mode,
3. Press the Standby/Source button on the soundbar repeatedly or press the
the indicator
4. Power on the connected external device and start playing.
on front of the soundbar will turn Violet(red+blue).

Bass
Treble
Balance
Select Move MENU Exit
Sound Mode Standard
Surround Off
AVL Off
Audio Language English
Picture Time Setup Lock Off
AudioAudio
Digital Output PCMDigital Output PCM
16
OPTICAL IN OPERATION
1. Connect the OPTICAL OUT jack from the external audio player (such as TV,
DVD player etc.) to the OPTICAL IN jack on the rear of the soundbar with the
optical connection cable as illustated below:(For PCM format only)
OPTICAL OUT
Optical Connection Cable TV or DVD player etc.
Rear View
AUX IN
OPTICAL IN LINE IN
L R AC IN
110V-240V
button on remote control to switch to the OPTICAL IN mode,
2. Press the Standby/Source button on soundbar repeatedly or press the OPTICAL
the indicator on
3. Power on the connected external player and start playing .
Turn on the digital audio output and set it to PCM (Pulse Code Modulation) type
similar to the below figure:
front of soundbar will turn Indigo(blue+green).

TROUBLESHOOTING
Play music/movie in the paired/
Sound distortion/rattle Volume level too high Reduce the volume level by pressing
Reduce the volume level of the
paired/connected device.
Bluetooth
reception failure Put the external BT device close to the
soundbar
Input source incorrect
Press and hold the standby/source button
Soundbar is in power off mode
The paired/connected device
is not in playback mode
The external device is
too far from soundbar
Remote Control
not functioning Out of range
The battery in the remote
control is drained
Point the remote control to the
remote sensor on the unit within
16 feet, +/-30 degress
Replace with new battery
No sound or
low sound Volume level in minimum position Raise the volume level by pressing
the VOL+ Button on soundbar
SYMPTOM POSSIBLE CAUSE POSSIBLE SOLUTION
No power The AC cable is not connected Connect the AC cable to the wall outlet
on soundbar or press the button
on remote control to power on
Or press VOL up button on remote control
repeatedly to switch to desired mode
the VOL - Button on the top of the
17
Press the standby/source button
connected device and make sure the
volume level is high
soundbar
Or press VOL down button on remote
control
Have not paired Pair the soundbar with the BT Device
as mentioned

SPECIFICATIONS
18
1x User Manual
1x Remote Control
1x AUX IN Cable
1x LINE IN Cable
1x Soundbar
Power Supply AC 110-240V – 50/60 Hz
Power Consumption 80W
Standy Power Consumption 0.5W
Sound Output 80W Peak Power
Audio Inputs Bluetooth, AUX, LINE IN, Optical
Bluetooth Version 5
Presets Jazz, Pop, Classic, Flat, Rock
Light Effects 11 Modes
Operating Temperature -10℃-40℃
Operating Humidity <=85%
Storage Temperature -40℃-80℃
Storage Humidity <=120%
Soundbar Weight (Net) 2.35 Kgs
Soundbar Dimensions (W x H x D) 940 x 76 x 76 in mm
Specifications and Accessories are subject to change w ithout notice.
What' s in the box

Warranty Terms & Conditions:
CloudWalker Streaming Technologies Pvt Ltd, Company incorporated in India under the provisions of the
Companies Act, 1956, which owns the brand 'CLOUDWALKER' (hereby referred to as the company)
warranties to the purchaser (hereby referred to as the Customer) that the CloudWalker Soundbar carries a
warranty of one year (12 months), that comprises of one year warranty on all parts including labour
charges, from the date of purchase as mentioned in the purchase tax invoice.
For availing the warranty services:
- Customer can call on our Toll Free No. 1800 102 3647 and register a call at our call centre
(we are open from 9:30 am to 6:00 pm, Monday to Saturday)
- Customer has to retain and show the original purchase invoice at the time of every complaint and
give a copy of it to the service engineer.
For any other queries/suggestions, please write to us at: [e-mail]
1YEAR
R
A
N
R
T
A
Y
W
1. This warranty is not applicable if the original purchase invoice is not presented to the company’s
authorized service personnel when asked for.
2. The warranty is confined to the first purchaser of the product from the date of purchase as
mentioned on the purchase invoice and is non-transferable. The warranty stands void in case of
transfer of ownership of this Soundbar.
3. Warranty is applicable only on producing the purchase tax invoice which mentions the product
model no & serial no.
4. The warranty is void if the Soundbar is not used in accordance to the instructions given in the
instruction manual.
5. The warranty does not extend to the Soundbar which has been damaged due to misuse, neglect,
accident or improper installation. Damages caused by the pests, natural calamities or abnormal
high/low voltage are also not covered by this warranty.
6. This warranty does not cover loss or damage in transit, whether carried by the company’s
transport or by the purchaser.
7. The warranty is void if the Soundbar is repaired by any agency non authorized by the company.
8. The warranty is void if the original serial number on the Soundbar is tampered, erased, modified or
if any alteration is made.
9. The warranty is void if any defects caused due to usage of external accessories / third party
accessories like batteries, adaptors, headsets, cables, memory cards / malwares / spywares /
virus / any applications other than operating system.

10. The warranty is void for any damages or defects arising due to normal wear and tear of parts,
cosmetic damages like scratches, paint peel off, color fading away / color changes, LED not
working, etc.
11. The warranty is void for any defects or damages arising due to customer induced damages,
physical damages, breakages, speaker defects caused due to unexpected external pressure, liquid
spill, air bubbles, black spot, black patches, liquid crystal damage, stains, dust inside the
Soundbar, defects arising due to high humid and moisture conditions or liquid/solvent/any
chemicals leakage in to the Soundbar while cleaning by the customer, modification or alteration of
any nature made in the electrical circuitry or physical construction of the product.
12. The company shall not be liable for any delay in rectifying the set, in the event of non-availability
of the components and shall in no way be responsible for any losses direct or indirect arising out
of the delay, if any.
13. The warranty does not extend to the accessories external to the Soundbar, if any, supplied with the
Soundbar (cables, remote).
14. In the event the Soundbar requires urgent attention, the purchaser should arrange to deliver the
same to the nearest service center at his/her own cost.
15. This Soundbar is meant for home entertainment purpose. Warranty is not valid if the Soundbar is
used for the commercial purpose.
16. The company's obligation under this warranty shall be limited to repair or providing replacement
of part/s only. This warranty shall not cover any consequential or resulting liability, injury, damage
or loss to property or life arising directly or indirectly out of any defect in the product.
17. The company or its authorized service centre, reserves the right to retain any part/s or
component/s replaced at its discretion in the event of a defect noticed in the Soundbar during the
warranty period. The part/s or component/s or unit/s replaced will become the property of the
company.
18. In the event of repairs / replacement of any part/s of the unit, this warranty will thereafter continue
and remain in force only for the unexpired period of the warranty. Moreover, the time taken for
repair / replacement and in transit, whether under the warranty or otherwise, shall not be excluded
from the warranty period.
19. Limitation of implied warranties: To the extent allowed by local law, this product is provided to you
“as is” without warranties or conditions of any kind, whether oral or written, expressed or implied.
CloudWalker specifically disclaims any implied warranties or conditions of merchantability,
satisfactory quality, non-infringement and fitness for a particular purpose.
20. This warranty is subjected to Mumbai Jurisdiction and operated through the courts located in
Mumbai Jurisdiction only. Your acceptance of the product is subject to acceptance of this
condition.
CAUTION
To prevent electrical shock, do not open the Soundbar. There are no user serviceable parts inside. Please refer to
qualified service personnel for repairs.
Disposal may be regulated in your community due to environmental considerations. For disposal or recycling
information, please contact 1800-102-3647 / 1800-200-0977 or email at [e-mail]
Customer’s Signature:
Dealer Name, Signature & Stamp: 1YEAR
R
A
N
R
T
A
Y
W