Club Piscine Maestrale User manual

Maestrale Gazebo l0'X 14' (20171
Assembly Instructions
Er101 41 g-

Security rules
Warninq :
Keep away flame or heat source from gazebo fabrics. Otheruvise fabrics can burn or melt and can
cause severe burn on nearby persons. ln this case, material damage has to be considered.
Moreover, the adding of any substance will block or severly slow down capacity of fabric to resist
or be flame retardant.
Regulation
It is the responsability of consumer being In accordance with city regulation, construction code,
zoning or any llmitations and obtaining permit prior erecting the gazebo.
Recommendation
Prior to proceed to erect the gazebo, a check-up of quantity of each items should be done. Some
parts may have sharp edges, wearing gloves is recommended.
Figure at least five hours to complete the set-up with two persons. Consider having enough time
for completion of erecting. Even well anchored, a non complete gazebo unit can get or create
damage to nearby environment.
Keep away from any electrlc installation or transportation device.
A check up of tlghtening of all bolts should be done all across lifespan of gazebo.
Even if this gazebo is built for year round use, this is strongly recommended to remove snow from
top.
Mosquito net and curtains (optional) must be removed from the unit at freezing period.
lnstruction manual must be read prior start-up of erecting.
All recommendation must be followed carefully to ensure perfect sturdiness of the unit.
Use proper tools and equipements for a safe and compliant installation. Never climb, sit or stand
on structure while erecting.
Anchoring bolts or other anchoring devices are not supplied.
Always recommended to keep instruction manual for further reference.

Care
Never use a high pressure washer, Use of mild soap in a lukewarm water is the best solution for
frame only. A clear water rinse is necessary then. Never use soap for fabrics, this will reduce
their capacity and consequently their lifespan and general look. For fabrics, a soft brush and a
lukewarm water is offering an excellent cleaning.
Warranty
Covered
This gazebo is warranty from any manufacturing defect for one year at normal use. This limited
warranty is for one year for parts only.
ln any case a part is needed, please contact the seller giving description and pictures of defect.
Not covered
All damage caused by commercial use, improper care, neglected storage, unreasonable or
abusive use, vandalism, chemical, freeze damage, extreme weather or act of God, rust,
oxidation, stains, glass breakage, packaging and transportation fees for return. Normal
discoloration and build-up of snow are not covered either.
Seller :
For each part request, please contact our customer service. lt will need a description of problem,
pictures and consumer invoice copy. Be aware full item code must appear on invoice to give
fabricating period, color and right identification of part requested. This will ensure all proper
information to proceed the request. Moreover, name of person in charge of the request must be
written, name and address of seller ( branch ), e-mail address, fax and phone number.

AF
AR
g
Y
AQø
AUñ
¡t
AJ
É-
Er
Ft
otn
AK
N
E_-
N
dY
N
NFl+
FAT
\Ë
l- 00u
X
W
SB
[[[lnv A
M
LðAQ AT
\
AU
AQET
FV
k
Á
N-
AT\J
\
tä+AFr
AIJNU
e{=S.
AY [[f f
Bs.
f [[[nv
3
@B{+

Reminder: Before assembly, don't forget to check inside of each Post (No.A),
some parts are well packed and stored inside.
A
The first Post (No. A) r-..{>
A
The second Post (No. A)+
A
The tnlr¿ Post (No. A) €>
A
M
N
o
U
V
2pcs
2pcs
1 pcs
4pcs
2pcs
o
AG
AR
AS
2pcs
2pcs
4pcs
4pcs
N
T
o
W
2pcs
2pcs
1 pcs
2pcs
L
R
S
2pcs
1 pcs
1 pcs
The fourtn Post (No. A) -.{>

PARTS LIST:
QTY Drawing
NO. Description
Post
Base flange
Base Cap
Corner supporter (Right)
Corner supporter (Left)
Long crossbar
Connector
Connector
Long crossbar
Connector
Short crossbar
Short crossbar
Corner connector

Drawing
NO. Description QTY
Corner roof tube
Roof connector 1
Roof support profile
Roof support profile
Middle roof tube
Middle roof tube
1
Middle connector
Upper roof supporting bar
Upper roof support tube 1
1
Upper roof support tube
Upper roof support tube
Middle roof support tube
Middle roof support tube

Description QTY Drawing
NO.
Middle roof support tube
Middle connector
Air vent corner connector
Roof cap 1
Air vent panel
Air vent panel
Air vent panel
Air vent panel
Air vent profile
Air vent profile
Right roof panel for 14' side
Right roof panel for 14' side
Middle roof panel for 14' side

NO. Description QTY Drawing
Left roof panel for 14' side
Left roof panel fort4' side
Right roof panel for 10' side
Right roof panel for 10' side
Left roof panel for 10' side
Left roof panel for 10' side
Corner connector
Eave profile
Eave profile
Corner moulding
Center moulding
1
Mosquito Net
AW Air vent Mosquito net 1

NO. Description QTY Drawing
AX Self tapping screw 26
AY Stake 16
Hardware Kit:
AA Bolt M6 X 15mm 195 @
BB Bolt M6 X 30mm 1B 0--r*
cc Bolt M6 X 42mm 30
DD Plastic washer 1B
EE Stainless washer 28
FF Allen key 1
GG Allen key I

ct)
o
Ë
I
ID TD
g
é
TD
I
A
Bõ
\'\ --'/

¡0000
0000
x2
1
E
X2x2
F1
F
These two holesmust face the ground.
^2 E
oEt
Ë-- FI+F
EFI
E
I
I
I
@
I@ @
I@I
I
@I
IIoI
I
IIt1
-I_\.-
A^^#.,
- - -
EF
Step 2:
lnsert the connectors (E1 & F1) into long crossbar (E) and long crossbar (F) and secure with bolts (AA). Do not
Repeat this step for remaining connectors (E1 & F1) and long crossbars (E & F). This is important to align
bottom holes of connectors (F1) with bottom holes of long crossbars (E & F). This care refer to a further
step.
1

0000
0000
Xx
2 2
Ez
G
X*2
2
HFt
These two holes must the ground.
G+ Ez H
FI
Attentionl!
Extra holes for short crossbar only.
GH
I
E
I
I
@
I@@
I@2
oII@I
I
_l 9F
II1
AÞ
Aå
(, H
Step 3:
lnsert the connectors (E2 & F1) into a short crossbar (G) and a short crossbar (H) and secure with bolts (AA).
Do not tiqht bolts comoletelv vet.
Repeat this step for remaining connectors (E2 & F1) and short crossbars (G & H). This is important to align ,
connectors threaded holes with short crossbars (G & H) holes. This care must either be taken to align (Fi)
connectors bottom holes to (G & H) short crossbars bottom holes. ln both cases, thls care ls lmportant
and refer to a further step.
12

Io
\Ao
E
oØ
F
ØA
0o\
II
A0P
\A
I
I
II
I
\
F
*-)%*
fuen
Step 4:
Secure long crossbars set (Ë & F) on two posts (A) by using bolts (AA).
Note fixing is done on both side of crossbars. Do not tight bolts completely yet.
Note : For your security, you may need two people for this step.
13
on

FG---0 F
o
Ø\tu'
\*
\- -0
AI
G
A
Ø
F
ØE
oE
F
AA
A
A
Step 5:
Secure short crossbars set (G & H) on posts (A) by using bolts (AA). Note fixing is done on both side of
crossbars (G A H). Repeat for the opposite side.
For your security, you may need 4 people for this step
Do not tight bolts completely yet.
14

@(à
Æ\ A@
AA
AA
G
H
ØØ
FEc
c
Step 6:
Secure left and right corner supporters (D A C) to posts (A) by using bolts (AA) as fig.1. Do not tight bolts yet.
Then secure other end of corner supporters (D & C) to short and long assembly crossbars (EFGH) by using bolts
1
1
sequencet external of corners, inside of corners, lower end of corner supporter then upper end. Prior tightening
crossbars, ensure assembly is fully aligned.
(M)as fig.2. Tightening must ng once are

l'-
o.
q)
U)
a
\
I
I
å
T
0-
I
6r-
v
I(o
(t
(g
c
L
o
C
L
o
o
'1
u)
q)
-o
5
o
o
g
L
o
c
L
o
o
o)
.g
c
'õ
E
o
L
L
o
o-
o
(t,
.9.
-c
õ
o
o-
o
É.
L
o
U'
C
!
o
c
L
o
C)
o
L
f
o
o
(t,

AAF /- -
*F
JK
J
tJ Jan\t
F
E
@G
H
@
Step 8:
1
1
corner roof tube set (J) on crossbars four corners and secure by using bolts (AA). Tight corner bolts but not full
17
corner ucom

J
P
ê
Þ
"\ -__ ---'l
1
Step 9:

Step 10: AS
secure cap
roug