Sunjoy A102010000 User manual

1/ 12
Assembly Manual
Item#: A102010000
Thank you for your purchase! We are pleased that you have chosen Sunjoy for your outdoor
furniture purchase.
Our clear, easy to follow, step by step instructions will guide you through the project from start
to finish

2/ 12
Safety information
•Keep all children and pets away from assembly area. Children and pets should be supervised
when they are in the area of the production construction.
•This package contains small items and plastic bags that should be kept away from children.
•Keep assembly area at least 6 ft. from any obstruction such as a fence, garage, house,
overhanging branches, laundry line or electrical wires.
•Proper placement of your product is essential. Do not place the product underneath electrical
lines.
•Keep fingers away from places where they can be pinched or trapped.
•Some parts may contain sharp edges, wear protective gloves if necessary during assembly.
•When assembling and using this product, basic safety precautions should always be followed
to reduce the risk of personal injury and damage to equipment. Please read all instructions
before assembly and use.
•Check all screws for tightness before and during usage. Ensure that all connectors and poles
are firmly and fully secured into position. It is important to do so before use so as to avoid a
possible collapse or damage to the item, which could also result in injury.
• This product is intended for outdoor use only. Install on flat, level ground.
•Stakes are provided to secure the gazebo in grass ground. If you wish to secure the gazebo
to a wood deck or concrete surface, you will need to purchase fasteners appropriate (such as
expansion bolt) for these surfaces. These are readily available at your local hardware store or
home center.
•The gazebo’s roof and structure are not guaranteed against extreme weather conditions
(storms, high winds, etc.). If the gazebo is not dismantled for the winter, snow must be cleaned
off regularly. Any damage caused by snow accumulation is not covered by the warranty.
•Do not use the unit during an electrical storm, as there is a remote chance of getting struck by
lightening.
•Do not leave the gazebo assembled when there is a risk of high wind, as possible damage will
occur to the structure. Remove fabric roof and secure screen & privacy panels.
•Warranty does not cover damage due to extreme weather conditions.
•Please check your state and local regulations prior to purchasing. Some jurisdictions may
require permits for, or otherwise regulate, installation and use.
Assembly Preparation
• Please read and understand this entire manual before attempting to assemble or install the
product. Keep this manual for future reference.
• Keep the original packaging to store the product.
•Before beginning assembly of product, make sure all parts are present. Do not attempt to
assemble the product if any parts are missing.
•Tools Required for assembly (NOT included): Screwdriver, a hammer, and 2 ladders that are
at least 2.4 m / 7.8 ft in height,
•This unit is heavy. Do not assemble this item alone. At least four or more people are
recommended for safe assembly.
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1 [phone] for anytime or email to
[email protected]

3/ 12
Description
Part#
Label
Qty
Image
Post
GZ1080XXX01
A
4
Left cross beam of long
side
GZ1080XXX02
B1
2
Right cross beam of long
side
GZ1080XXX03
B2
2
Left cross beam of shot
side
GZ1080XXX04
B3
2
Right cross beam of shot
side
GZ1080XXX05
B4
2
Parts List

4/ 12
Description
Part#
Label
Qty
Image
Beam connector
GZ1080XXX06
C
4
Corner
cover(Outside)
GZ1080XXX07
D
4
Corner
cover(Inside)
GZ1080XXX08
E
4
Middle beam
connector
GZ1080XXX09
F
6
Slanting bar
connector
GZ1080XXX10
G
4
Left decorative bar
of long side
GZ1080XXX11
H1
2
Right decorative
bar of long side
GZ1080XXX12
H2
2
Left decorative bar
of short side
GZ1080XXX13
H3
2
Right decorative
bar of short side
GZ1080XXX14
H4
2
Top frame
GZ1080XXX15
I
1
Top frame cover
GZ1080XXX16
J
1
Slanting bar
GZ1080XXX17
K1
4
Middle bar
GZ1080XXX18
K2
6
Hook
GZ1080XXX19
L
1
Left small PC panel
GZ1080XXX20
M1
4
Left big PC panel
GZ1080XXX21
M2
4
Middle PC panel
GZ1080XXX22
M3
4
Right small PC
panel
GZ1080XXX23
M4
4

5/ 12
Description
Part#
Label
Qty
Image
Right big PC panel
GZ1080XXX24
M5
4
Long bar cover
GZ1080XXX25
O1
8
Short bar cover
GZ1080XXX26
O2
2
Left lock plate of
lower slanting bar
GZ1080XXX27
P1
4
Right lock plate of
lower slanting bar
GZ1080XXX28
P2
4
Left lock plate of
lower middle bar
GZ1080XXX29
P3
6
Right lock plate of
lower middle bar
GZ1080XXX30
P4
6
Decorative slot
connector
GZ1080XXX31
Q
4
Left PC panel
connector
GZ1080XXX32
R1
4
Right PC panel
connector
GZ1080XXX33
R2
4
Middle PC panel
connector
GZ1080XXX34
R3
2
Post base
GZ1080XXX35
S
4
Base cover
GZ1080XXX36
T
4
Left arch support bar
GZ1080XXX37
U1
4
Right arch support
bar
GZ1080XXX38
U2
4

6/ 12
Description
Part#
Label
Qty
Image
M6*15 Bolt
BM06015C
AA
92
M6 Washer
UD06C
BB
108
M6*15 Screw
SM06015C
CC
16
M6 Wrench
W10D
Z1
2
Hardware Pack 1
Fig.1: Raise up the Base cover(T)and then attach the Post base(S) to the Post(A) by using Screw(CC) and
Washer(BB).
Fig.2-1：Attach the Left cross beam of long side (B1) and Right cross beam of long side (B2) to Beam
connector(C) by Bolt (AA) and Washer (BB).
Fig.2-2：Attach the Left cross beam of short side (B3) and Right cross beam of short side (B4) to Beam
connector(C) by Bolt (AA) and Washer (BB).

7/ 12
Description
Part#
Label
Qty
Image
M6*15 Bolt
BM06015C
AA
32
M6 Washer
UD06C
BB
32
Hardware Pack 2
Fig.3-1：Attach the Middle beam connector (F) to the Left cross beam of short side (B3) and Right cross
beam of short side (B4) by Bolt (AA) and Washer (BB).
Fig.3-2：Attach the Middle beam connector (F) to the Left cross beam of long side (B1) and Right cross beam
of long side (B2) by Bolt (AA) and Washer (BB).
Fig.4：Attach the assembled cross beam (B1) and (B3) to the Post (A) by Bolt (AA) and Washer (BB), Use
the same way to assemble the cross beam (B3) and (B4).
Fig.5：Attach the Slanting bar connector (G) to the cross beam of long side (B1/B2) and cross beam of short
side (B4/B3) by Bolt (AA) and Washer (BB).
Fig.6：Attach the arch support bar(U1,U2) to the cross beam(B1、B2、B3、B4) and Post (A) by Bolt (AA)
and Washer (BB).

8/ 12
Hardware Pack 3
Description
Part#
Label
Qty
Image
M6*15 Bolt
BM06015C
AA
70
M6 Washer
UD06C
BB
74
M6*45 Bolt
BM06045C
FF
4
Φ8*260 Stake
DD08260C
II
16
Fig.9：Attach the upper end of the Middle bar (K2) to the Top frame (I) by Bolt (AA) and Washer (BB).
Fig.10：Attach the lower end of the Middle bar (K2) to the Middle bar connector (F) by Bolt (AA) and
Washer (BB).
Fig.11：Attach the Top frame cover (J) to the Top frame (I) by Bolt (AA) and Washer (BB), then screw
the Hook (L) to the Top frame (I).
Fig.7：Four people and two ladders are needed to assemble during this step.
Note1: Two people to assemble the upper end of slanting bar, another two people to assemble the lower
end of the slanting bar.
Note2: Assemble the middle bar by the same way.
Fig.7-1：Attach the upper end of the Slanting bar (K1) to the Top frame (I) by Bolt (AA) and Washer (BB).
Fig.8：Attach the lower end of the Slanting bar (K1) to the Slanting bar connector (G) by Bolt (AA) and
Washer (BB).

9/ 12
Fig.12：Insert the left small PC panel (M1) to the slot of the Slanting bar (K1) and Middle bar (K2). Assemble
the Right small PC panel (M4) and the Middle PC panel (M3) by the same way.
Fig.13：Insert the Left PC panel connector (R1) into the slot of Slanting bar (K1) and Middle bar (K2).
Assemble the Right PC panel connector (R2) and Middle PC panel connector (R3) by the same way.
Fig.14：Insert the Left big PC panel (M2) to the slot of the Slanting bar (K1) and Middle bar (K2). Assemble the
Right big PC panel (M5) and the Middle PC panel (M3) by the same way.
Fig.15：Attach the Right lock plate of lower slanting bar (P2) to the Slanting bar connector (G) by the Bolt (AA)
and Washer (BB).Attach the Left lock plate of lower slanting bar (P1) to the Slanting bar connector (G) by the
same way.
Fig.16：Attach the Left lock plate of lower middle bar (P3) to the Middle beam connector (F) to keep the Left
big PC panel (M2) stable by Bolt (AA) and Washer (BB). Use the same way to assemble the Middle PC
panel (M3) by Left lock plate of lower middle bar (P3) and Right lock plate of lower middle bar (P4). Make
sure all the Bolts are screwed tightly.

10 / 12
Fig.18-1: Attach the Left decorative bar of long side (H1) and Right decorative bar of long side (H2) to the
Middle bar (K2) by Bolt (AA) and Washer (BB).
Fig.18-2: Attach the Right decorative bar of short side (H4) to the Middle bar (K2) by Bolt (AA) and Washer
(BB).
Fig.19: Attach the Decorative slot connector (Q) to the Left decorative bar of short side (H3) and Right
decorative bar of short side (H4) by Bolt (AA) and Washer (BB). Attach the connector (Q) to decorative bar
(H1) and (H2) by the same way.
Fig.17-1：Attach the Left decorative bar of long side (H1) to the Right decorative bar of long side (H2) as
the fig.17-1 shows. Assemble the decorative bar H3 & H4 by the same way.
Fig.17-2.Attach the decorative bar(H1, H2, H3, H4) to the cross beam (B1、B2、B3、B4) as the fig.17-2
shows. (Note: Two people are needed during this step.)
Fig.20-1: Attach the Short bar cover (O2) to the connecting part of Left decorative bar of long side (H1) and
Right decorative bar of long side (H2) by Bolt (AA) and Washer (BB).
Fig.20-2: Attach the Long bar cover (O1) to the decorative bar (H1/H3) and decorative bar (H2/ H4) as the
Fig.20-2 shows.
Fig.21: Put Corner cover (Outside) (D) through Post (A) to the corner of decorative bar (H1/H3) and
decorative bar (H4/H2), fix them by Bolt (FF) and Washer (BB).
Fig.22：Attach the Corner cover (Inside) (E) to the Post (A) by Bolt (AA) and Washer (BB).
Fig.23：Fix the assembled gazebo to the ground by using Stakes (II).