CO-Z DWD-ZB01-00 User manual

WATER DISTILLER
USER MANUAL
Read Carefully Before Use
Keep for Future Reference
V20230529

1
Safety Information
• ONLY use this distiller with stable and compatible power sources.
• DO NOT let children or persons with impaired physical or mental capacities operate this device
without strict supervision.
• DO NOT use this device when its outer casing is wet as this may lead to short circuits, re, or
electrocution.
• Be careful during use as this device produces VERY hot water vapor that can cause instant
scalding. Always lift the lid to the side while avoiding the escaping steam. Do not lift the lid
straight up.
• DO NOT use this device if its power cables are damaged in any way. Repair or replace the
damaged wiring before use.
• DO NOT place the bottle into a cold environment after lling it with hot distilled water as this
may cause it to crack or shatter.
• Disconnect the power to this device before performing any maintenance.
Warning!
Specications
US UK
Input Power 110–120V/60Hz 220–240/50Hz
Rated Power 750 W 750 W
Volume of Water Tank 4.2 qt. or 1.1 gal. (4 L) 4 L (3.5 qt. or 0.88 gal.)
Processing Rate 1.1 qph or 0.26 gph (1 L/h) 1 L/h (0.88 qt./hr. or 0.22 gal./hr.)
Temperature Safety Cuto󰀨 300°F (150°C) 150°C (300°F)
Net Weight 4.6 kg (10.14 lb.) 10.14 lb. (4.6 kg)
Dimensions 11.2 × 10.4 × 18.7 in.
(28.5 × 26.5 × 47.5 cm)
28.5 × 26.5 × 47.5 cm
(11.2 × 10.4 × 18.7 in.)

2
Product Diagram
Collection
Bottle
Hot Air
Heated Fluid
Lid
Main Tank
Cooling System
Activated Charcoal Filter
Collection Cap
Output Nozzle
Collection
Bottle
Protective
Coating
Heating Element

3
Package List
1. Distiller
The distiller works by heating water into vapor and subsequently cooling it down so that it
condenses back into water without its previous impurities.
2. Collection Bottle
This bottle collects your distilled water.
3. Collection Cap
This cap collects the distilled water & directs it into the bottle.
4. Bottle Cap
This cap seals the bottle between uses.
5. Activated Charcoal Filter
This lter absorbs smaller impurities that are not eliminated through distillation.
6. Power Cord
This cord connects any grounded (3-pronged) outlet to power the distiller's heating element.
7. Chamber Cleaning Powder
This powder is used to clean the distiller, specially designed not to damage its lining.
8. Instruction Manual
You're reading this.
9. Silicone Tube
This tube can be used to connect the distiller to another receptacle besides the provided bottle.

4
Setup
Bottle Assembly
Secure the collection cap on top of the bottle by twisting it on clockwise.
Distiller Assembly
The silicone seal prevents water from escaping the distiller. When placing or replacing it, ensure
that the rounded side is facing up.
✔

5
Align the collection cap with the distiller's spout. Optionally, use the provided silicone tubing to
directly connect the spout with the bottle or another recepticle.
Remove the outlet nozzle from the lid and insert the charcoal packet into it. Reattach and secure
it onto the distiller’s lid as shown. Check that the seal remains in place.

6
Maintenance
Disconnect the distiller from its power source and allow it to fully cool before undertaking any
cleaning, maintenance, or repair.
Rinse and wipe the tank daily using clean water. Make sure it is dry when not in use. Calcium
deposits and residue can accumulate on the stainless-steel lining. Monthly cleanings are
recommended. To clean the tank:
1. Pour in hot water until all the residue is covered.
2. Add 1–4 teaspoons of the provided cleaning powder, depending on the amount of residue.
3. Wash the inside of the distiller’s cap with a soft cloth.
4. Rinse these components with clean water, but do not allow any electrical component to
become wet.
5. If there is any remaining residue, repeat this process.
Operation
�$
1. Open the distiller. Add water up to the maximum water level line.
2. Replace the top of the distiller and make sure it is properly sealed.
3. Plug in the power cord.
4. Press
Reset to begin distillation cycle.
Water will begin to pour out of the distiller after about 30 minutes. It will take roughly 4 hours
for a full distillation cycle to complete. Wait 10 minutes between cycles before adding water
to start a new batch.
5. Wait 15 minutes once the distillation cycle ends before removing the lid cover. Open the lid
to the side to avoid any escaping steam. Do not open the lid straight up or leave your hand
where it might be scalded.

7
Contact Us
Thank you for choosing our products! If you have any questions or
comments, contact us at [email protected] and we'll resolve your
issue ASAP!
For a .pdf copy of the latest version of these instructions, use the
appropriate app on your smartphone to scan the QR code to the right.
Troubleshooting
Do not use corrosive agents or steel cleaning instruments as this may damage the stainless
steel lining.
Cleaning the bottle should be done with warm soapy water. Never alternate between hot and
cold water as this may damage the bottle.
The silicone seal should be removed and cleaned monthly. When placing it back onto the
distiller’s cap, ensure that the rounded side of the ring is placed facing up.
Possible Problems Typical Solutions
Insu󰀩cient water comes out
Fill the tank to the line
Check the silicone seal for wear or misplacement
Correct the alignment of the spout and bottle or use
the provided tube
Machine becomes jittery
Check the silicone seal for wear or misplacement
Check that the lter is properly aligned with the bottle
Distilled water has an odd odour
Replace the charcoal lter
Halt the distillation process for 10–15 minutes before
its regular end point, to prevent it from running dry
and burning residual minerals left by the water
Distilled water has black debris Remove the damaged charcoal lter from the nozzle,
clean the nozzle, and insert a new charcoal packet
The reset button has
malfunctioned
Connect the distiller to a surge protector and turn it on
and o󰀨 using the surge protector's power switch
DWD-ZB01-00 DWD-ZBUK-00
Rev. 29 May 2023