Puretec HYBRID H6 User manual
For correct operation & installation it is essential to observe these instructions.
Filtration & Ultraviolet Disinfection All in One Unit
Hybrid User Guide
ATS5200.103
Licence No. WM 74593
ApprovalMark
SEPT2016
2Installation & Operation Manual Copyright © Puretec Pty Ltd 2016
What's Inside
What's Inside
Puretec Customer Service ................................................................................................. 3
Introduction................................................................................................................................. 3
Preparing your system.......................................................................................................... 4
Positioning your System ...................................................................................................... 5
Power Surge Protection........................................................................................................ 5
Installation Requirements................................................................................................... 6
Installation Procedure ........................................................................................................... 7
Operation...................................................................................................................................... 9
.......................................................................................................................... 9
Lamp Installation/Replacement Procedure ........................................................... 10
Lamp Ballast Operation .................................................................................................... 11
............................................................................................ 11
Replacement Parts Guide................................................................................................. 11
Cartridge Installation/Replacement ........................................................................... 12
Quartz Sleeve Maintenance Procedure..................................................................... 13
Troubleshooting Guide ...................................................................................................... 14
Warranty .................................................................................................................................... 15
Product Information
Distributor
Installer
Phone
Date Installed
3
HYBRID Filtration & Ultraviolet Disinfection All in One Unit
Puretec Customer Service
system. Your system is a proven performer manufactured from only quality materials
and components and will give years of ‘spring fresh’ water free of impurities if
maintained and installed properly (refer installation requirements p.6)
Introduction
quality.
The system is designed for mains and rainwater supply but can be used in other
situations. For other types of water supply please contact your local Puretec stockist or
The Puretec Hybrid system cartridges and lamp needs replacing regularly to maintain
optimum performance. This is a simple procedure when following instructions. For
replacements contact your nearest Puretec stockist.
Your new Hybrid system incorporates a lamp failure system design feature that enables
you to be warned of a lamp failure by :
1. A lamp failure LED
2. An audible alarm
correctly.
Introduction
4Installation & Operation Manual Copyright © Puretec Pty Ltd 2016
Preparing the system
Preparing your system
The Puretec systems are designed to run economically for many years and this is
dependant on the initial installation and periodical maintenance.
Please read all instructions carefully as failures caused by incorrect installation or
operation are not covered by warranty.
transportation. You should have:
On removing your Puretec Hybrid system from its carton you should check all
components to ensure all are present and have not been damaged in transportation.
As a responsible manufacturer we care about the environment. As such we urge you
to follow the correct disposal procedure for your product and packaging materials. You
must dispose of this product and its packaging according to local laws and regulations.
For correct operation & installation it is essential to observe these instructions.
User Guide
Filtration & Ultraviolet Disinfection All in One Unit
Hybrid H6 / H7
ATS5200.103
LicenceNo. WM 74593
ApprovalMark
5
HYBRID Filtration & Ultraviolet Disinfection All in One Unit
Installation Guide
Positioning your System
Choose a location where water spillage will not cause damage. Make sure mounting
for changing the cartridges.
Choose a site with a structurally appropriate mounting position on the wall. Allow a
chamber length space above the unit for removal of the lamp and sleeve from the
cartridges and maintenance.
To protect your Hybrid system make sure the site is frost free and has adequate
occur from leaking pipe joints or seals.
Power Surge Protection
An electrical power surge or spike can travel on the supply lines and cause serious
replaceable) to protect the circuit. The fuse is not a lightning arrestor and may not
A suitable surge protection device should be used on all electrical equipment or warranty
may be voided.
Do not use long extension leads as they may cause substantial voltage drop and/or poor
lamp performance.
We recommend the use of an RCD or earth leakage circuit breaker on the power
supply to your unit.
6Installation & Operation Manual Copyright © Puretec Pty Ltd 2016
Installation Requirements
• Cold water line only.
•
•
•
device must be installed.
•
•
25mm threads.
Note: Only use thread seal tape. Do not use liquid sealant
• Application warning; minimum water characteristics must be met before installation
•
maximum rated current draw of 5.7A.
•
tape to ensure airtight seal and do not over tighten. To prevent strain on unit
threads always support heavy inlet and outlet pipes.
• Where the water being pumped contains unusually high levels of dissolved solids
on the quartz sleeve may occur over time. Maximum recommended parameters are
as follows:
Iron less than 0.3 mg/L
less than 0.05 mg/L
Suspended Solids less than 10mg/L
Manganese less than 0.05 mg/L
Hardness less than 110mg/L
•
should be cleaned or replaced as required to maintain them in good condition.
Note:Thiswaterlteringapplianceshouldonlybeinstalledbyalicensedplumber.
Installation Procedure
7
HYBRID Filtration & Ultraviolet Disinfection All in One Unit
The outlet pipework within 1 metre
should be metal or poly.
Puretec.
is deemed a problem we recommend installing a temperature management
Installation Procedure
Puretec Hybrid Series has 1" [25mm] plumbing connections.
1. Before attempting installation check the unit to ensure the sleeve is intact and the
lamp is present.
2. Locate a suitable position for the Hybrid system remembering to allow 120mm
under the unit (H7 model) and 700mm clearance above the unit for cartridge and
lamp changes. A power plug is required.
allow min. 120mm clearance from the ground
700mm clearance
700mm clearance
In InOut Out
HYBRID H6 & H8 MODEL HYBRID H7 & H9 MODEL
Installation Procedure
8Installation & Operation Manual Copyright © Puretec Pty Ltd 2016
Installation Procedure
wall.
10. Turn the power on and ensure that the lamp is operating. (see also lamp installation
instructions).
Please store them safely.
Note:Lostormisplacedkeysarenotcoveredbywarranty.
169
12
20
40
100.7
88
9
HYBRID Filtration & Ultraviolet Disinfection All in One Unit
Operation
Operation
• On a new installation where no other form of sterilisation has been in constant
the pipework for at least an hour and preferably overnight.
• The sanitising solution can be dosed to the water tank or if necessary added as a
and suitable for use in drinking water. If added as a shock dose it should be rinsed
out through a nearby tap.
cause serious burns to unprotected eyes.
Lamp Installation/Replacement Procedure
1.
2.
Parts become hot during operation.
Allow to cool before servicing.
3.
chamber through the hole of the aluminium nut. Connect the white lamp connector
to the pins on the lamp. Do not let go of the lamp until the lamp is connected to the
socket.
Nevertouchthequartz(glass)andlampsurfaceasspotsofngerprintsmay
interferewithUVtransmission.Iflampisdirtied,pleasecleanlampwithalcohol
basedcleaner.
4. Place white lamp connecter back on the aluminium nut. Turn on the power. Make
Note:Forinitialuse,wait3-5minutestoallowwatertopassthroughthewholeunit.
Turnonpointofusetoletwaterowthroughtheunitfor2-3minutestoreleaseair
andimpuritiesfromsystem.
10 Installation & Operation Manual Copyright © Puretec Pty Ltd 2016
Operation
User Guide 4
Water
Outlet
O-Ring
Lamp Power
Connector
Quartz
Sleeve
UV lamp
Aluminium
Nut
Safety
Cap
Ballast
Stainless Steel
Chamber
Water
Inlet
Power
Plug
5. Reset the lamp timer by depressing the reset button until an audible “beep” sounds
indicating that the lamp timer has been reset for a further 12 months.
water quality
11
HYBRID Filtration & Ultraviolet Disinfection All in One Unit
Lamp Ballast Operation
Lamp Ballast Specications
Lamp Power: 21W~105W
Lamp Current: 1.10A~1.30A
Ambient Temperature: 0~40°C
Lamp Rated Life: 365 days
Caution: High voltage ground earth ballast case to avoid possible shock hazard
Replacement Parts: HYBRID H6 HYBRID H7
Stage 1 Pleated Cartridge PL05MP1 PL05MP2
Stage 2 Dual Purpose Cartridge DP10MP1 DP10MP2
Stage 3 UV Lamp, 50 W RL5 RL5
Replacement Parts: HYBRID H8 HYBRID H9
Stage 1 Pleated Cartridge, PL20MP1 PL20MP2
Stage 2 Polyspun Cartridge, PX01MP1 PX01MP2
High Output UV Lamp, 50 W RL5 RL5
Replace cartridges every 6 months.
We recommend replacing UV lamp annually
Replacement Parts Guide
periodically (this is dependant on water quality and usage).
You can obtain replacement cartridges from your local Puretec dealer. To maintain
replacements.
Operation
12 Installation & Operation Manual Copyright © Puretec Pty Ltd 2016
Cartridge Installation/Replacement
the red pressure relief button on the housings.
Remove old cartridges.
silicone lubricant (or similar).
making sure cartridges is properly seated over spigot in base of bowls. Remember
to record the model no. of the cartridges you use.
6 Hold bowls upright while screwing onto head. Make certain that the spigot in the
housing heads is located centrally to the cartridges to make a good seal. Hand
7 Open downstream tap to allow air to be released and gently open water supply
allowing all air to be purged.
it may be necessary to replace the cartridges.
Replacement Guide
13
HYBRID Filtration & Ultraviolet Disinfection All in One Unit
Maintenance
Quartz Sleeve Maintenance Procedure
every 3 months depending on quality of water source) and see whether there is dirt
or substances gathered. Clean with alcohol based cleaner if necessary. Allow the
unit to cool before servicing.
lamp. Turn the aluminium nut at the top of the chamber counterclockwise and
carefully remove the quartz sleeve.
3 Soak a piece of cloth in vinegar or citric acid to clean the quartz sleeve.
4 Put the quartz sleeve back into the stainless steel chamber.
Important: The round end will rest on the internal chamber cradle. There will be
at).
5 Press down lightly on the open end of the
sleeve and it locks down into place squarely
on at 13mm. You will hear and feel it pop
down into place.
Moreorlessthanthisindicatesthesleeve
maynotbeproperlylocatedandserious
damagecouldresultwhentheend-capis
ttedand/orthesystemisrepressurized.
nut.
Connect the lamp connector to the pins on the lamp. Do not let go of the lamp until
the lamp is connected to the socket.
Nevertouchthequartz(glass)andlampsurfaceasspotsofngerprintsmay
interferewithUVtransmission.Iflampisdirtied,pleasecleanlampwithalcohol
basedcleaner.
start operation with no alarm.
13 mm
14 Installation & Operation Manual Copyright © Puretec Pty Ltd 2016
Troubleshooting Guide
SYMPTOMS POSSIBLE CAUSE POSSIBLE SOLUTION
Ballast and/or breaker tripped
Ballast damaged
Reset ballast and/or breaker
Replace ballast
Ballast or breaker
repeatedly trips
Connection between lamp and lamp plug
is wet
Clean and dry lamp pins and
condensation
Replace ballast
Leak at inlet or outlet
Cracked heads
and retighten
Replace heads
Leak detected from
Condensation of moist air on cold
chamber (slow accumulation)
incorrectly installed
Lamp/sleeve assembly not properly
installed (too tight or not tight enough)
Control humidity or relocate unit
Inspect and replace if deteriorated
System is operating
but water tests
reveal bacterial
contamination
is acting as a breeding ground for
pathogens
Pathogens are residing in the distribution
Lamp reached the maximum lamp life
treatment equipment Ensure
all distribution lines have been
with chlorine
Replace lamp on or before lamp
counter reached 0.
Lamp timer does not
read anything
Power cord is damaged
Power surge caused damage to electrical
assembly
Plug unit into AC power outlet
Replace fuse or reset breaker
Replace power cord
Replace ballast
Leak detected at
incorrectly installed
Filter cartridge not centered
cartridge is centered
Red lamp blinks and
buzzer sounds
Lamp has reached or nearing the
maximum lamp life
Lamp is disconnected or faulty
Replace lamp on or before lamp
counter reached 0.
needed
Power interrution Reset ballast
Error Code ‘A3’ on
ballast
life expired
Replace lamp
15
HYBRID Filtration & Ultraviolet Disinfection All in One Unit
Warranty
AUSTRALIAN WARRANTY
Any claim under this warranty must be made within 3 years of the date of purchase of the product. This product is warrantied to
be free of defect of material and workmanship for 3 years from date of purchase. Warranty is 3 years parts and 1 year parts and
claim to place of purchase for consideration.
The warranty only applies if the product was used and/or installed in accordance with the user guide and/or installation instructions.
This warranty is given in lieu of all other express or implied warranties and manufacturer shall in no circumstance be held liable for
damages consequential or otherwise or delays caused or faulty manufacturing except as excluded by law.
This warranty is provided in addition to other rights and remedies you have under law: Our goods come with guarantees which
cannot be excluded under the Consumer Guarantees Act. You are entitled to replacement or refund for a major failure and to
compensation for other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a major failure.
NOTES
circumstances a pressure limiting valve is not required. If incoming water pressure is excessive it may however be
impurities etc.
NEW ZEALAND WARRANTY
Any claim under this warranty must be made within 3 years of the date of purchase of the product. This product is warrantied to
be free of defect of material and workmanship for 3 years from date of purchase. Warranty is 3 years parts and 1 year parts and
claim to place of purchase for consideration.
The warranty only applies if the product was used and/or installed in accordance with the user guide and/or installation instructions.
This warranty is given in lieu of all other express or implied warranties and manufacturer shall in no circumstance be held liable for
damages consequential or otherwise or delays caused or faulty manufacturing except as excluded by law.
This warranty is provided in addition to other rights and remedies you have under law: Our goods come with guarantees which
cannot be excluded under the Consumer Guarantees Act. You are entitled to replacement or refund for a major failure and to
compensation for other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a major failure.
This manual suits for next models
3
Table of contents
Other Puretec Water Filtration System manuals
Puretec
Puretec Multitrol MUL-E3 Series User manual
Puretec
Puretec IL-UB Series User manual
Puretec
Puretec Basic HD Series User manual
Puretec
Puretec NTR-E3 Series User manual
Puretec
Puretec PureMix Z2 User manual
Puretec
Puretec ROS2700 User manual
Puretec
Puretec Z1-RW-K User manual
Puretec
Puretec HYBRID Series User manual
Puretec
Puretec WU-UV Series User manual
Puretec
Puretec TSI Series User manual
Puretec
Puretec IMB Series User manual
Puretec
Puretec CO-RO270 Series User manual
Puretec
Puretec CR-Z2 User manual
Puretec
Puretec RO270 User manual
Puretec
Puretec Hybrid-R Triple Series User manual
Puretec
Puretec RI-HF19 User manual
Puretec
Puretec Hybrid-M1 User manual
Puretec
Puretec 2CI-C User manual
Puretec
Puretec MaxiPlus MPB202B User manual
Puretec
Puretec MaxiPlus MP Series User manual
Popular Water Filtration System manuals by other brands
HydroLogic
HydroLogic smallBoy HGC728875 user manual
A.O. Smith
A.O. Smith AO-US-200 owner's manual
Vortex
Vortex 85-1448-10 (10 GPM) Installation and service manual
Pentair
Pentair Predator II owner's manual
Judo
Judo JRSF Series Installation and operating instructions
Advance acoustic
Advance acoustic FREEZE WS8824 manual
US Water Systems
US Water Systems Fusion Oxi-Gen 089-FSF OG Series Installation, operation and maintenance manual
TCi
TCi MFC A installation instructions
Prozone Water Products
Prozone Water Products Complete Sanitation System 15 instructions
AquaCo
AquaCo SYS-RO924TM5 Operations & installation guide
JRC
JRC NSVS1127 manual
GOSUN
GOSUN FLOW user manual
Global Industrial
Global Industrial 641753 manual
Pneumatic Division
Pneumatic Division IS-F35 Installation & service instructions
ChemoformGroup
ChemoformGroup Summer Fun SF 122 Installation and operating instructions
DVZ
DVZ OILCHIEF 150 FSU operating manual
3M
3M Aqua-Pure AP810 manual
Mega
Mega Filter Max Series user manual