Puretec HybridPlus Series User manual

For correct operation & installation, it is essential to observe these instructions.
SEPT2020
WMTS103:2016
Certicate No. WM 74593
Australian Certication
Services
User Guide
Complete Household Water Filtration & Pressure System
HybridPlus™Series
22
22
21
21
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
DO NOT OVERTIGHTEN.
DO NOT USE
LIQUID SEALANTS.
SURGE PROTECTION
REQUIRED /
NO EXTENSION CORDS.
SURGE PROTECTION
REQUIRED /
NO EXTENSION CORDS.

2Installation & Operation Manual Copyright © Puretec Pty Ltd 2020
What's Inside
Product Information
Distributor:
Installer:
Phone:
Date Installed:
What's Inside
Puretec Customer Service ................................................................................................. 3
Introduction................................................................................................................................. 3
Preparing Your System ......................................................................................................... 4
Positioning Your System ...................................................................................................... 5
Power Surge Protection........................................................................................................ 5
Installation Requirements................................................................................................... 6
Initial Installation Procedure.............................................................................................. 8
UV Lamp Diagram................................................................................................................ 15
Operation................................................................................................................................... 16
Radre UV Unit....................................................................................................................... 16
Lamp Ballast Operation .................................................................................................... 16
Lamp Ballast Specications............................................................................................ 16
Replacement Parts Guide................................................................................................. 17
Cartridge Replacement Procedure............................................................................... 18
Lamp Replacement Procedure ..................................................................................... 19
Quartz Sleeve Maintenance/Replacement Procedure....................................... 20
Troubleshooting Guide ...................................................................................................... 23
Warranty .................................................................................................................................... 25

3
HYBRIDPLUS SERIES | Complete Household Water Filtration & Pressure System
Puretec Customer Service
Thank you for purchasing a Puretec HybridPlus Series Complete Household Water
Filtration & Pressure System. Your system is a proven performer manufactured from
quality materials and components and will give years of ‘spring like’ water, free of
impurities, if maintained and installed properly (refer installation requirements p.6).
HybridPlus P3, P6, P9 & P12 models include a Grundfos pump and are covered by
Grundfos for the warranty as stated in the Grundfos user guide. For assistance please
call the Puretec Customer Service Helpline on 1300 140 140 (Australia) or
0800 130 140 (New Zealand).
Introduction
Puretec's HybridPlus Series is specically designed to kill harmful bacteria in untreated
water supplies and to deliver stable water ow on demand to every tap/outlet in the
house. It uses a natural purication process that’s eco-friendly and
chemical-free. It includes pre-ltration to ensure that particulate matter does not shield
micro-organisms from the UV light.
This system will eectively treat water, depending on the required UV dosage and
existing water quality.
The HybridPlus systems are suitable for tank only, mains water back-up, bore water and
surface water treatment (subject to water quality) but can be used in other situations.
For other types of water supply please contact your local Puretec stockist or call our
Puretec Customer Service Helpline on 1300 140 140 (Australia) or
0800 130 140 (New Zealand).
The Puretec HybridPlus system cartridges and lamp need replacing regularly to maintain
optimum performance. This is a simple procedure when following instructions. For
replacements contact your nearest Puretec stockist.
Your new Hybrid system incorporates a failure warning feature that warns you of a lamp
failure by:
1. An LED warning light
2. An audible alarm
In addition, when the alarm “beeps” on and o, the lamp is due to be changed so
eective treatment is maintained. A Green LED indicates that the system is operating
correctly.
Introduction

4Installation & Operation Manual Copyright © Puretec Pty Ltd 2020
Forcorrect operation & installation, it is essential to observe these instructions.
SEPT2020
WMTS103:2016
Certicate No. WM 74593
Australian Certication
Services
User Guide
CompleteHousehold Water Filtration & Pressure System
HybridPlus™Series
SHEET
DESCRIPTION
REV.
NUMBER
MATERIAL
WEIGHTTREATMENT SCALE
3RDANGLE
PROJECTION
APPROVEDBY
DATE
DATE
MODIFICATIONS
REV.
DRAWNBY
DRAWNBY
SUPPLYSPECIFICATION DERIVEDFROM
1/1
1:1
PETERKENNEDY ROSSBUTCHER
304GRADESTAINLESSSTEEL
NATURAL
N/A
800g
PHK5000-5
A
INTRODUCTION
25/02/2020
25/02/2020
PETERKENNEDY
N/A
A
HOUSINGUVCHAMBERHYBRIDGSERIES
DIMENSIONSAREINMILLIMETRES
DONOTSCALE
0+-1.0mm
0.0+-0.5mm
0.00+-0.1mm
ANGLES:
DIMS.
0+-1.0deg.
A A
B B
C C
D D
E E
F F
G G
H H
J J
K K
L L
M M
N N
P P
R R
T T
24
24
23
23
22
22
21
21
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
A0
NAME
HOUSING
DONOT OVERTIGHTEN.
DONOT USE
LIQUIDSEALANTS.
SURGEPROTECTION
REQUIRED/
NOEXTENSION CORDS.
SURGEPROTECTION
REQUIRED/
NOEXTENSION CORDS.
UV LAMP SPANNER
USER GUIDEKEYS
Preparing the system
Preparing Your System
Puretec systems are designed to run economically for many years, dependent on the
initial installation and periodical maintenance.
Please read all instructions carefully as failures caused by incorrect installation or
operation are not covered by warranty.
On removing your Hybrid system from its carton you should check all the components
(especially the lamp), to ensure all are present and have not been damaged in
transportation. Depending on your model, you should have:
Remove all the packing materials prior to use.
As a responsible manufacturer we care about the environment. We urge you to follow
the correct disposal procedure for your product and packaging materials. You must
dispose of this product and its packaging according to local laws and regulations.
1. HybridPlus System
2. UV Lamp (in cardboard tube)
3. Bag containing Spanner, User Guide,
Spring and Surge Protector
HYBRIDPLUS SYSTEM
SPRING
+ EXTRA HOSES X 2 (ONLY SUPPLIED WITH P1 MODELS)

5
HYBRIDPLUS SERIES | Complete Household Water Filtration & Pressure System
Positioning Your System
Positioning Your System
Choose a location with a structurally appropriate position. Allow a chamber length space
above the unit for removal of the lamp and sleeve from the Radre UV system during
servicing and allowance for the swing doors to open (see Fig. 5).
To protect your HybridPlus system make sure the site is frost free and has adequate
ventilation. Choose a location with adequate drainage and where water spillage will not
cause damage that may occur over time from leaking pipe joints or seals.
Power Surge Protection
An electrical power surge or spike can travel on the supply lines and cause serious
damage to your electrical equipment. The Radre UV Electronic ballast has a fuse
(non-replaceable) to protect the circuit. The fuse is not a lightning arrester and may not
protect the Radre if lightning or a very powerful surge hits the unit.
A suitable surge protection device has been provided with this product. Puretec
recommends the use of a surge protector (the one supplied or otherwise) or warranty
may be voided.
WARNING: The Arlec power surge protector that is provided is not
weatherproof & MUST be protected from water/moisture.
It would usually be sucient for the surge protector to be installed under the eaves of
a house and/or out of the weather, otherwise, it would need to be suitably protected.
Ensuring the surge protector is suitably protected from water/moisture is the
responsibility of the user. Alternatively a hard-wired outdoor surge protector my be
installed by a qualied electrician or an outdoor rated surge protector may also be used.
Re-order code for surge protectors: PC-SURGE
Do not use long extension leads as they may cause substantial voltage drop and/or poor
lamp performance.
We recommend the use of an RCD or earth leakage circuit breaker on the power
supply to your unit.

6Installation & Operation Manual Copyright © Puretec Pty Ltd 2020
Installation Requirements
• Puretec HybridPlus systems should be protected from harsh environments where
overexposure to salt or aggressive chemicals can occur.
• Cold water line only.
• Power supply: AC 240V | 50Hz
• Supply pressure: 300-520 kPa. Install pressure limiting valve if pressure exceeds
520 kPa.
Note: For point of entry installations an approved dual check backow
prevention device must be installed.
• Supply temperature 0 - 52 °C (protect from freezing).
• Alternative ttings may be required if being connected to anything other than
25 mm threads.
Note: Only use thread seal tape. Do not use liquid sealant.
• Ensure the water supply ow rate does not exceed the rated maximum ow rate of
the HybridPlus system.
• Ensure the electrical power supply to the HybridPlus system is sucient, allowing
for other appliances that may be connected to the circuit e.g. pump, and ensuring it
is surge protected, and protected against brown-outs. If in doubt, please consult a
qualied electrician.
• Use unions at pipe connections to enable easy removal and servicing. Use sucient
tape to ensure airtight seal and do not over tighten. To prevent strain on the unit
always support heavy inlet and outlet pipes.
• Where the water being treated contains unusually high levels of dissolved solids
particularly hard water, iron, manganese or biological organisms, a deposit build up
on the quartz sleeve may occur over time. Maximum recommended parameters are
as follows:
Iron: less than 0.3 mg/L
Hydrogen Sulde: less than 0.05 mg/L
Suspended Solids: less than 10mg/L
Manganese: less than 0.05 mg/L
Hardness: less than 110mg/L
Application warning: minimum water characteristics must be met before
installation of Radre™ to ensure proper operation and continuous protection.
Installation Requirements

7
HYBRIDPLUS SERIES | Complete Household Water Filtration & Pressure System
• If stated water quality parameters are exceeded; pre-ltration is required as water
of this quality can compromise the eectiveness of the UV system. The lters
and the sleeve should be cleaned or replaced as required to keep them in good
condition.
• If bacteria has been present prior to the installation of this system, we recommend
ushing the pipelines with Puretec TankSafe.
• The system should not be used for any other purpose without specic referral to
Puretec.
• Heating of water is an integral feature associated with UV systems and if this
is deemed a problem we recommend installing a temperature management
valve, which is installed inline immediately aer the system and releases water
periodically. Ordering code is RI-TMS4.
 Note:Thiswaterlteringapplianceshouldonlybeinstalledbyafullyqualied&
licencedplumber.
Installation Note: A water lter system/tap, like any product, has a limited lifespan
and if not replaced, will eventually fail. Failure can happen early due to unforeseen
circumstances. To avoid possible property damage, this product should be regularly
examined for leakage and/or deterioration and replaced when necessary. We strongly
recommend that a drain pan, plumbed to an appropriate drain or outtted with a
leak detector, be used in those applications where any leakage could cause property
damage. We also strongly recommend that the water supply be turned o, upstream
to the water lter system/tap, if no one is home for an extended period of time.
INSTALLATION SHOULD BE COMPLETED BY QUALIFIED TRADESPEOPLE.
FAULTY OPERATION DUE TO UNQUALIFIED PERSONS WILL RESULT IN VOIDED
WARRANTY COVERAGE.
Installation Requirements

8Installation & Operation Manual Copyright © Puretec Pty Ltd 2020
Installation Procedure
Fig 1. As Supplied Outlet/Inlet Connections P9 & P12 Models
DATE
REV.
PETER KENNEDY
N/A
A
INTRODUCTION
25/02/2020
DIMENSIONS ARE IN MILLIMETRES
0 +- 1.0mm
0.0 +- 0.5mm
0.00 +- 0.1mm
ANGLES:
DIMS.
0 +- 1.0deg.
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
8
8
7
7
6
6
5
5
4
4
Power Cord
Mains Water Inlet
Rainwater Inlet
Pure Water Outlet
Pure Water
Hose
Rainwater
Hose Mains Water
Hose
Rains/Mains Water
Hose to Filters
Filtered Water
Hose to UV unit
As standard the HybridPlus P9 & P12 systems come as shown below.
Initial Installation Procedure
The Puretec HybridPlus Series has 1" [25mm] plumbing connections. It can be congured
so the water inlet/outlets and the power cord can be installed on the le or right of the
unit. This allows extra exibility for a variety of installations. The unit comes with the
water inlet connections on the le and the outlets on the right side of the unit.

9
HYBRIDPLUS SERIES | Complete Household Water Filtration & Pressure System
23
23
22
22
21
21
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
8
8
Power Cord
Rains/Mains Water
Hose to Filters
Pure Water Outlet
Rainwater Inlet
Mains Water Inlet
Mains Water
Hose
Rainwater
Hose
Pure Water
Hose
Filtered Water
Hose to UV Unit
Installation Procedure
Fig 2. Alternative Outlet/Inlet Connections Example P9 & P12 Models
To change the connection conguration unscrew the coupling nut on the outside of the
cabinet and redirect the hose and the coupling to the side/connection desired. You will need
to remove the rubber plug from the selected connection port to insert the coupling and
fasten the coupling nut to secure the tting.
Hose
Coupling
Nut
Rubber
Gasket
Coupling
Ensure cutout on
coupling locks down into
the wall of the unit.
Secure the coupling on the outside
of the unit with the rubber gasket
& coupling nut.
Fig 3. How To Use Couplings

10 Installation & Operation Manual Copyright © Puretec Pty Ltd 2020
Fig 4. As Supplied Plumbing Connections - P3 & P6 Models
The HybridPlus P3 & P6 systems come supplied as shown below and are designed to be
used for dedicated rainwater supplies. The inlet and outlet of the rainwater supply and
the power cord can be switched to dierent sides of the unit as shown in Fig 2.
Installation Procedure
DATE
REV.
DRAWN BY
SUPPLY SPECIFICATION DERIVED FROM
PETER KENNEDY
N/A
A
INTRODUCTION
25/02/2020
DIMENSIONS ARE IN MILLIMETRES
0 +- 1.0mm
0.0 +- 0.5mm
0.00 +- 0.1mm
ANGLES:
DIMS.
0 +- 1.0deg.
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
8
8
7
7
6
6
5
5
4
4
Power Cord
Rainwater Inlet
Pure Water Outlet
Pure Water
Hose
Rainwater
Hose
Rainwater Hose to
Filters
Filtered Water
Hose to UV unit

11
HYBRIDPLUS SERIES | Complete Household Water Filtration & Pressure System
REV.
DRAWN BY
SUPPLY SPECIFICATION
PETER KENNEDY
A
DIMENSIONS ARE IN MILLIMETRES
0 +- 1.0mm
0.0 +- 0.5mm
0.00 +- 0.1mm
ANGLES:
DIMS.
0 +- 1.0deg.
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
8
8
7
7
6
6
5
5
Fig 5. As Supplied Plumbing Connections - P1 Models
The HybridPlus P1 system comes supplied as shown below.
The unit comes with the water inlet connections on the le and
the outlets on the right side of the unit but can be recongured to
suit as per Fig 2.
Note: This model does not include a pump or switchover valve
but has the allowance to install your own pressure system into
the unit. Max pump dimensions: 560 (H) x 540 (W) x 240 (D) mm.
Installation Procedure
Power Cord
Pure Water Outlet
Pure Water
Hose
Rains/Mains Water
Hose to Filters
Filtered Water
Hose to UV unit
2 x hoses
Hole Provisions
for Inlet/Outlet
Connections Can be connected to either mains water, rainwater or
via your own pressure system.
Allowance for
your own pressure
system installation
2 x couplings
(W)
(D)
(H)
Rubber Pump Mat
Extras provided :

12 Installation & Operation Manual Copyright © Puretec Pty Ltd 2020
1. Before attempting installation check the unit to ensure the quartz sleeve is intact within
the Radre UV chamber.
2. Locate a suitable position for the HybridPlus system, remembering to allow 380 mm
either side of the unit, 260 mm in front of the unit for the swing doors and 700 mm
clearance above the unit for lamp changes (see Fig 5). A power outlet is required.
Installation Procedure
Fig 6. Installation Clearance
DESCRIPTION
NUMBER
MATERIAL
WEIGHTTREATMENT SCALE
APPROVED BY
DATE
DATE
MODIFICATIONS REV.
DRAWN BY
SUPPLY SPECIFICATION DERIVED FROM
1 : 1
PETER KENNEDY ROSS BUTCHER
304 GRADE STAINLESS STEEL
NATURAL
N/A
800 g
PHK 5000 - 5
A
INTRODUCTION
25/02/2020
25/02/2020
N/A
HOUSING UV CHAMBER HYBRID G SERIES
DIMENSIONS ARE IN MILLIMETRES
0 +- 1.0mm
0.0 +-0.5mm
0.00 +- 0.1mm
ANGLES:
DIMS.
0 +- 1.0deg.
23
23
22
22
21
21
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
NAME
HOUSING
380 mm clearance 380 mm clearance
260 mm clearance
in front of the swing doors.
700 mm clearance
above the unit for lamp changes.

13
HYBRIDPLUS SERIES | Complete Household Water Filtration & Pressure System
3. The HybridPlus can remain on the adjustable feet without mounting/anchoring the unit.
BOLTED INSTALLATION For the prevention of vandalism, movement subject to
vibrations etc. The system can be bolted to a steady platform/concrete slab.
a. First, you will need to remove the housing bowls and cartridges from the system to
allow access room. If the bowls are dicult to undo, the spanner provided may be
used to make it easier. Note which order the cartridges are in to ensure when they
are re-installed they are in the same order.
b. Drill the holes for the anchors into the platform or slab. Unscrew and remove the
feet from the bottom of the cabinet. Locate the anchor holes inside the bottom
of the unit and secure the unit in place using stainless steel anchor bolts with a
maximum diameter of 12mm & a minimim length of 125mm (not included). See Fig.
7 for details.
c. Once secure, re-install the cartridges and housing bowls. Hold bowls upright while
screwing in the housings. Make certain that the spigot in the housing heads is
located centrally to the cartridges to make a good seal. Use the provided spanner to
tighten lter bowl until rm. DO NOT OVER TIGHTEN.
Installation Procedure
Fig 7. Anchor the System (optional)
SHEET
DESCRIPTION
REV. NUMBER
MATERIAL
WEIGHTTREATMENT SCALE
3RD ANGLE
PROJECTION
APPROVED BY DATE
DATE
MODIFICATIONS REV.
DRAWN BY
DRAWN BY
SUPPLY SPECIFICATION DERIVED FROM
1 / 1
1 : 1
PETER KENNEDY ROSS BUTCHER
304 GRADE STAINLESS STEEL
NATURAL
N/A
800 g
PHK 5000 - 5
A
INTRODUCTION
25/02/2020
25/02/2020
PETER KENNEDY
N/A
A
HOUSING UV CHAMBER HYBRID G SERIES
DIMENSIONS ARE IN MILLIMETRES
0 +- 1.0mm
0.0 +- 0.5mm
0.00 +- 0.1mm
ANGLES:
DIMS.
0 +- 1.0deg.
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
NAME
HOUSING
Unscrew & remove each
adjustable foot.
APPROVED BY DATE
MODIFICATIONS
REV.
DRAWN BY
SUPPLY SPECIFICATION DERIVED FROM
PETER KENNEDY ROSS BUTCHER
N/A
A
INTRODUCTION
25/02/2020
N/A
DIMENSIONS ARE IN MILLIMETRES
DO NOT SCALE
0 +- 1.0mm
0.0 +- 0.5mm
0.00 +- 0.1mm
ANGLES:
DIMS.
0 +- 1.0deg.
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
24
24
23
23
22
22
21
21
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
8
8
7
7
6
6
5
5
4
4
A0
Locate each anchor
hole & secure to
the platform/ slab
(anchor bolts not
included).

14 Installation & Operation Manual Copyright © Puretec Pty Ltd 2020
6. Turn the water o and purge the lines.
7. Plumb inlet and outlet pipe work to the Hybrid unit. Both the inlet and outlet are a
25 mm female brass connection.
Warning: Use PTFE thread seal tape on all connections. Use of pipe sealants
will void warranty.
8. Open the swing doors to the unit.
9. Remove the safety cap from the aluminium nut, if the nut is
inadvertently loosened during this process, retighten the nut.
Insert the spring into the ballast by dropping it into the chamber.
Slowly insert UV lamp into chamber through the hole of the
aluminium nut end. Connect the lamp connector to the pins on
the lamp. Do not let go of the lamp until the lamp is connected
to the socket (seeFig.8&9).
Nevertouchthequartz(glass)andlampsurfaceasmarks
orngerprintsmayinterferewithUVtransmission.Iflampis
soiled,pleasecleanlampwithanalcoholbasedcleaner.
10. Put safety cap on the aluminium nut. Connect the ground wire to the chamber. Plug
in power connector.
11. Check the main power cord for the unit is plugged in and the power is on.
12. Check each housing bowl and ensure they have not become loose in transport. Use
the provided spanner to tighten lter bowl until rm. DO NOT OVER TIGHTEN.
13. (Pump Models Only) Check the power cord for the pump is plugged in (power is
o).
14. (Pump Models Only) Ensure that water is reaching the pump, this may require
siphoning the line to begin water ow.
15. (Pump Models Only) Turn on the power to the pump.
16. Turn the water on, let the water ow through – opening a tap downstream to ush
the unit for 1-2 minutes. Then check the system thoroughly for leaks.
 Note:Forinitialuse,wait3-5minutestoallowwatertopassthroughthewhole
unit.Turnonadownstreamtaptoletwaterowthroughtheunitfor2-3minutesto
releaseairandimpuritiesfromthesystem.
17. Turn the power to the UV system on and ensure that the lamp is operating. Make
sure that the GREEN LED is illuminated (refer Lamp Replacement Procedure on
pg.14).
18. Close and lock the swing doors. Note: Your cabinet comes with 2 keys for your
convenience. Please store them safely.
 Note:Lostormisplacedkeysarenotcoveredbywarranty.
Installation Procedure
12
valve
IN OUT
10
mins
45
78
Replacing UV Lamp
valve
IN
3
Fig. 8
Lamp
Connector

15
HYBRIDPLUS SERIES | Complete Household Water Filtration & Pressure System
UV Lamp Diagram
15 14 13 12 11 10 9 8 7 6 5
Grounding Wire
Safety Cap
Aluminium Nut
Lamp
O-ring
Stainless Steel
Chamber
Water Inlet
O-ring
Aluminium Nut
Water Outlet
Fig. 9 UV Lamp Diagram
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
8
8

16 Installation & Operation Manual Copyright © Puretec Pty Ltd 2020
Operation
Radre UV Unit
• Prior to performing any work on the UV steriliser system, always disconnect the
power supply.
Warning: Do not look directly into ultraviolet rays emitted from the UV lamp as
they will cause serious burns to unprotected eyes.
• The treated water will seem warm for a short period at rst ow. This is because
the UV lamp emits heat. When turning on a tap, let the water run for a short time to
purge any warm water.
Lamp Ballast Operation
Press the mode button to cycle the display between lamp life remaining and total
running days.
Press and hold the silver button for 15 seconds to reset lamp life timer or until
'reset' appears on the screen.
To silence the 'lamp life end' alarm for 7 days, press and hold on the silver button
until 'delay' appears on the screen.
Lamp Ballast Specications
AC 240V | 50Hz
Lamp Power: 35W~95W
Lamp Current: 0.8A~0.9A
Ambient Temperature: 4~40°C
Lamp Rated Life: 365 days
Caution:Groundtheballastcasingtoavoidpossiblehighvoltageshockhazard
Operation
• Allow two minutes for the UV lamp to reach full intensity before using the outlet
water.
• On a new installation where no other form of sterilisation has been in use, we
recommend ushing the pipe work with a suitable sanit iser such as TankSafe™(for
dosage refer to TankSafe™ product instructions). This solution should be le in the
pipework for at least an hour and preferably overnight.
The sanitising solution can be added into the water tank or if necessary added as a
shock dose into the bowl of the lter housing of the HybridPlus and slowly ushed
through the piping. If added as a shock dose the system and pipework should be
rinsed thoroughly by opening a downstream tap.

17
HYBRIDPLUS SERIES | Complete Household Water Filtration & Pressure System
Replacement Parts Guide
To maintain a high quality of puried water, the cartridges will need changing
periodically (dependent on water quality and usage).
You can obtain replacement cartridges from your local Puretec dealer. To maintain
performance, warranty and Australian Standards use genuine Puretec replacements.
Replacement Parts Guide
Replacement Parts: Stage 1
Cartridge*
Stage 2
Cartridge
Stage 3
Cartridge UV Lamp Quartz
Sleeve
HYBRIDPLUS
(ALL MODELS) PL05MP2 CB05MP2 PX01MP2 RL6 RQS6
Replace cartridges every 6 months. UV Lamps must be replaced annually in order to maintain 99.9% kill
rate of bacteria.
*Stage 1 Cartridge is nearest to the water inlet.
Fig. 10 Cartridge Replacement Diagram
22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5
Shut O Valve
Red Pressure
Relief Buttons

18 Installation & Operation Manual Copyright © Puretec Pty Ltd 2020
Cartridge Replacement
Cartridge Replacement Procedure
To change the lter cartridges please adhere to the following procedure:
1 Turn water supply o using the shut o valve located inside the unit (see Fig 10)
and relieve the pressure by opening a downstream tap or pressing the red pressure
relief button on the housings.
2 Unscrew the lter bowls. If the bowl is dicult to undo, the spanner provided may
be used to make it easier. Remove old cartridges and dispose in the correct manner.
3 Clean bowls with soap and warm water and rinse thoroughly. Check O-rings for
damage and replace if necessary.
4 Check O-ring lubrication and if necessary apply a light coating of food grade silicone
lubricant (or similar).
5 Remove all packaging from new lter cartridges and insert into housing bowls
making sure cartridges are properly seated over the spigot in base of the bowls.
Remember to record the model number of the cartridges you use & install date.
6 Hold bowls upright while screwing in the housings. Make certain that the spigot
in the housing heads is located centrally to the cartridges to make a good seal.
Tighten the bowls until rm. HAND TIGHTEN ONLY. DO NOT OVER TIGHTEN.
7 Open a downstream tap to allow air to be released and gently open water supply
allowing all air to be purged.
8 Allow water to run for 1-2 minutes to ush the system.
9 Close down stream tap and check the Hybrid system for leaks. Flush system for 1-2
minutes aer any period of non-use more than 2 weeks. For a period of non-use of
6 months or more, it may be necessary to replace the cartridges.

19
HYBRIDPLUS SERIES | Complete Household Water Filtration & Pressure System
Lamp Replacement
Lamp Replacement Procedure
Prior to performing any work on the UV steriliser, always disconnect the power
supply rst.
1 Turn water o and release the water pressure.
Parts become hot during operation.
Allow to cool before servicing.
2 Unlock and open the swing doors on the unit.
Disconnect the lamp connector and ground
wire. Grip the end of the lamp and carefully
disconnect the power socket.
Slowly remove the old lamp from the chamber.
3. Remove the packaging on the new lamp. Slowly insert into chamber through the
hole of the aluminium nut end. Connect the lamp connector to the pins on the lamp.
Do not let go of the lamp until the lamp is connected to the socket (seeFig.9).
Nevertouchthequartz(glass)andlampsurfaceasmarksorngerprintsmay
interferewithUVtransmission.Iflampissoiled,pleasecleanlampwithanalcohol
basedcleaner.
4. Secure the lamp connector on the aluminium nut end. Connect the ground wire to
the chamber. Plug in power connector, the RED LED will be illuminated (when the
lamp life timer is reset in step 6 the LED will turn green).
5. Restore water supply and check the unit for leaks. Re-check the unit aer 1 hour.
 Note:Forinitialuse,wait3-5minutestoallowwatertopassthroughthewhole
unit.Turnonadownstreamtaptoletwaterowthroughtheunitfor2-3minutesto
releaseairandimpuritiesfromsystem.
12
valve
IN OUT
45
78
Replacing UV Lamp
3
Cleaning Quartz Sleeve
123
valve
IN OUT
10
mins
456
Replacing UV Lamp
78 9
Replacing UV Lamp
IN OUT
12
45
O Ring
Fig. 11

20 Installation & Operation Manual Copyright © Puretec Pty Ltd 2020
Maintenance Procedure
Quartz Sleeve Maintenance/Replacement Procedure
To ensure high sterilising rate with best water quality, check the sleeve regularly
(about every 3 months depending on quality of water source) and see whether
there is dirt or substances gathered. Allow the unit to cool before servicing. Prior to
performing any work on the UV sterilizer, always disconnect the power supply.
1. Turn o the power and water to the unit and
release the water pressure (using the red
buttons above the unit's lters).
Parts become hot during operation.
Allow to cool before servicing.
2. Unlock and open the swing doors to the unit.
To disconnect the lamp connector, detach the
earthing wire, grip the white cap and carefully
disconnect from the aluminium nut.
3. Slowly remove the UV lamp from the chamber.
4. Unscrew and remove the aluminium nut on the
12
valve
IN OUT
45
Replacing UV Lamp
78
Replacing UV Lamp
Cleaning Quartz Sleeve
123
valve
IN OUT
10
mins
456
Replacing UV Lamp
12
45
O Ring
Cleaning Quartz Sleeve
123
valve
IN OUT
10
mins
456
Replacing UV Lamp
12
45
O Ring
valve
10
mins
456
78
Replacing UV Lamp
valve
IN OUT
3
O Ring
Fig. 12
6 Press and hold the silver button for 15 seconds, when an audible "beep" will sound,
indicating that the lamp life timer has been reset for a further 12 months.
7. Close and lock the swing doors. Note: Your cabinet comes with 2 keys for your
convenience. Please store them safely.
 Note:Lostormisplacedkeysarenotcoveredbywarranty.
We recommend replacing UV lamp annually to ensure high sterilising rate with best
water quality.
Always keep UV lamp on, as power uctuation will shorten the service life of the UV
lamp.