Co2meter GasLab SAN-102 User manual

© Copyright 2018,CO2Meter, Inc. All Rights Reserved. Last modified November 2,2018 1
GasLab SAN-102 Micro Oxygen Monitor
User Manual
The GasLab SAN-102 is a wearable, personal safety meter designed to monitor ambient
oxygen levels in real time. It is designed to protect workers in confined spaces.
Features
•Audible and visual low / high oxygen level alarm
•Silicone boot and metal clip are light and comfortable to wear
•Electrochemical sensor, no consumable parts
•Includes ambient temperature and % relative humidity sensors
•Lithium-ion rechargeable battery. USB Charging port
•Runs 4+ days per charge
Applications
•Stored Gases in Confined Spaces.Industrial use of stored or piped gases creates the
possibility that oxygen in breathable air could be displaced by gases such as nitrogen,
helium, argon or carbon dioxide resulting in a hazardous condition.
•Underground Tunnels, Caves or Mines. Over time oxygen can be displaced by other
naturally occurring gases like carbon dioxide, carbon monoxide, ammonia, methane and the
oxidation of sulfides resulting in lower oxygen levels than is required for personal safety.
•Combustion in Confined Spaces. Combustion first uses up the available oxygen, then
produces partial oxidation of carbon (carbon monoxide), hydrogen cyanide, and nitrogen
oxides. Hydrogen gas can also be produced and displace oxygen.
Please take a moment to read these instructions before use. They will provide you with
all the necessary information for the correct use of your oxygen monitor.

Copyright © CO2Meter, Inc. All Rights Reserved
PAGE 2 of 6
Theory of Operation
The SAN-102 Oxygen Monitor uses an electrochemical sensor to determine the concentration
of oxygen in air samples. Air reaches the sensor by diffusing through the openings on the back
of the unit. Normal air movement is enough to carry the sample to the sensor.
Device
1. OLED display
2. Power button
3. Fahrenheit and Celsius switching button
4. Alarm LED
5. Micro USB charge port
6. Vent
7. Clip
8. Silicone boot
OLED Display
1. Oxygen concentration
2. Air Temperature (°F or °C)
3. % Relative Humidity
4. Oxygen Concentration Units (%)
5. Battery Charge Indicator
OPERATION
Plug the USB cable into the meter and a 120VAC wall adapter. It will take approximately 2
hours to receive a full charge. Once the meter is charged, it can run 4+ days before recharging.
Press the power button to turn on the meter.
When the meter is first turned on, it performs a 10 second countdown for device warm up, then
enters normal display with current oxygen level readings displayed. The device starts taking
measurements when powered on and updates readings every 3 seconds.
The OLED display will turn off automatically after 120 seconds of inactivity to conserve battery
power. However, the sensor will continue to monitor the O2 level. Briefly press the Power button
to view the display.
Hold down the Power button for 3 seconds to turn the meter off. This will conserve the battery’s
charge until you need to use the meter again.

Copyright © CO2Meter, Inc. All Rights Reserved
PAGE 3 of 6
Low and High Oxygen Level Alarm
The SAN-102 is equipped with audible and visual alarms to alert you when the ambient oxygen
concentration exceeds either ofthe two factory preset alarm levels:
•Danger Low Oxygen Alarm: 19.5% - LED will flash and audible alarm will sound 3x / sec.
•Warning High Oxygen Alarm: 23.5% - LED will flash and audible alarm will sound 2x / sec.
Normal atmosphere contains between 20.8% and 21% oxygen. OSHA defines any atmosphere
that contains less than 19.5% oxygen as “oxygen deficient” and any atmosphere that contains
more than 23.5percent oxygen as “oxygen enriched.” These levels arefactory set and cannot
be changed.
Fahrenheit and Celsius Switching
•Press the °F/°C button to switch between the two temperature units.
•Press the Power button briefly to save the temperature setting andreturn to normal display.
Low Battery Alarm
The meter continuously measuresthe rechargeable battery’s voltage.Ifitdrops to a critical
level, the low battery alarm will sound until the battery isrecharged or the battery power is
depleted.
Note that the meter can continue to monitor oxygen levels while charging.
CLEANING AND STORAGE
The front panel and case can be cleaned with a mild solution of detergent and water. Apply
sparingly with a soft cloth and allow drying completely before using. Donotusearomatic
hydrocarbons orchlorinated solvents for cleaning.
ATTENTION! - If a Warning or Danger alarm is triggered
while using the instrument as a safety monitor, leave
the area and seek fresh air immediately. Remaining on
site under such circumstances can cause serious
impairment or even lead to death.
Calibration
The SAN-102 comes pre-calibrated from the factory. However, the O2 sensor should be
calibrated at least once a year, or as described in your company's safety procedures. You can
perform the calibration yourself, or you can return it to CO2Meter for factory calibration at a
nominal fee.
SAN-102 can be atmospherically calibrated. By pressing the Fahrenheit and Celsius
switching button for 4 seconds, the monitor will enter O2 atmospherically calibration mode.
While in calibration mode, press the Fahrenheit and Celsius switching button quickly to
switch between atmospherically calibration or Exit. Press the Power button to confirm.
The atmospherically calibration will not require additional materials but must be performed in
outdoor (fresh air) during the entire procedure.
The temperature and humidity sensors do not require calibration and should remain accurate
for the life of your unit.

Copyright © CO2Meter, Inc. All Rights Reserved
PAGE 4 of 6
SPECIFICATIONS
Oxygen Sensor Specifications
Measurement Range
0 to 30.0% vol.
Resolution
0.1% vol.
Temperature Range
-20 to 50°C (-4°F ~ 122°F)
Humidity Range
0 to 99%RH
Baseline Drift (-10-50°C)
<1% change in output @ 3 months
Expected Lifespan
24 months
Temperature Sensor Specifications
Temperature Range
-20.0 to 60.0°C (-4 to 140°F) display
Display Resolution
0.1°C (0.1°F)
Display Options
°C/°F(switchable)
Accuracy
±
0.5°C( ±0.9°F)
Response Time
5~30 seconds(device must equilibrate with environment)
Humidity Sensor Specifications
Measurement Range
0.0 to 99.9%RH
Display Resolution
1%RH
Accuracy
±
4.5%RH
Response Time
<8 seconds for 63% of step change
General
Operating
-20°C to 50°C (-4°F to 122°F),0~99% RH non-condensing
Storage
-20°C to 60°C(-4°F to 140°F),<99% RH non-condensing
Power Supply
Li-ion battery(4.2V, 400mAh)
Dimensions
60x35x25mm (2.36x1.38x0.98”)
Weight
45 grams (1.58oz.)
TROUBLESHOOTING GUIDE
Symptom / Issue
Possible Cause / Resolution
Device does not power
ON
Make sure the power supply is connected properly
and that there is power at the outlet. Use the
supplied adapter. Verify that your meter has had
enough time to charge before turning it on.
Reading does not
change
In fresh air, you will rarely see oxygen levels
change. This is normal.

Copyright © CO2Meter, Inc. All Rights Reserved
PAGE 5 of 6
OXYGEN RECOMMENDED LEVELS
•> 23.5% Oxygen enriched, presents significant fire and explosion risk
•20.8 - 21% Normal oxygen level in fresh air
•19.5% Lowest safe oxygen level limit (OSHA)
•< 16% Headache, nausea, difficulty performing manual tasks
•< 12%Difficulty breathing, impaired coordination and perception
•< 10% Poor judgement and bluish lips
•< 8% Fatal within minutes if not treated
•< 6% Fatal in 40 seconds
SUPPORT
The quickest way to obtain technical support is via email. Please send all support inquires to
[email protected].
Please include a clear, concise definition of the problem and any relevant troubleshooting
information or steps taken so far, so we can duplicate the problem and quickly respond to your
inquiry.
WARRANTY
This meter comes with a 1 YEAR (warranty period) limited manufacturer’s warranty, starting
from the date the meter was shipped to the buyer.
During this period of time, CO2Meter.com warrants our products to be free from defects in
materials and workmanship when used for their intended purpose and agrees to fix or replace
(at our discretion) any part or product that fails under normal use. To take advantage of this
warranty, the product must be returned to CO2Meter.com at your expense. If, after examination,
we determine the product is defective, we will repair or replace it at no additional cost to you.
This warranty does not cover any products that have been subjected to misuse, neglect,
accident, modifications or repairs by you or by a third party. No employee or reseller of
CO2Meter.com’s products may alter this warranty verbally or in writing.
LIABILITY
All liabilities under this agreement shall be limited to the actual cost of the product paid to
CO2Meter.com. In no event shall CO2Meter.com be liable for any incidental or consequential
damages, lost profits, loss of time, lost sales or loss or damage to data, injury to person or
personal property or any other indirect damages as the result of use of our products.

Copyright © CO2Meter, Inc. All Rights Reserved
PAGE 6 of 6
RETURNS
If the product fails under normal use during the warranty period, a RMA (Return Material
Authorization) number must be obtained from CO2Meter.com. After the item is received
CO2Meter.com will repair or replace the item at our discretion.
To obtain a RMA number, call us at(386) 256-4910 or email us at [e-mail].
When requesting a RMA please provide reason for return and the original order number.
If we determine that the product failed because of improper use (water damage, dropping,
tampering, electrical damage etc.), or ifitisbeyond the warranty date, we will inform you of the
cost to fix or replace the product.
For additional warranty information visit ourwebsite:
www.co2meter.com/pages/terms-conditions
CONTACT US
We are here to help!
Forinformation or technical support,please contact us.
s[email protected]
[phone] (Technical Support)
[phone] (Sales)
www.co2meter.com
CO2Meter, Inc.
131 Business Center Drive
Ormond Beach, FL 32174 USA