Kistler KiDAQ 5500A User manual

Instruction
Manual
KiDAQ Data Acquisition
Type 5500A
KiStudio Lab
Type 2910A
5500A_002-943e-09.21

Foreword
5500A_002-943e-09.21 Page 1
Foreword
This instruction manual applies to the data acquisition
system KiDAQ Type 5500A.
Keep this instruction manual for future reference. It
should be available at the point of use.
Information in this instruction manual is subject to change
any time, without notice. Kistler reserves the right to
improve and modify its products in the course of technical
advancement, without any obligation to inform any
persons or organizations of such changes.
Information in this document is subject to:
•KiStudio Lab software Type 2910A R5.0.1
•KiDAQ Data Acquisition Type 5500A with KiDAQ
Controller 5551A firmware R5.0.24
•LabAmp Type 5165A with firmware R2.1.1
(restricted release for use with KiStudio Lab only)
•LabAmp Type 5167A with firmware R2.1.1
(restricted release for use with KiStudio Lab only)
Last manual update 15.09.2021
© 2019 … 2021 Kistler Group. All rights reserved.
Kistler Group
Eulachstrasse 22
8408 Winterthur
Switzerland
Phone [phone]
[email protected]
www.kistler.com

Type 5500A and 2910A
Page 2 5500A_002-943e-09.21
Content
1. Introduction and Important Notes ............................................................................................. 4
1.1 Disposal Instructions for Electronic Devices....................................................................... 4
1.2 Software Upgrades and Updates........................................................................................ 4
1.3 Repairs at Kistler................................................................................................................. 4
2. System Overview......................................................................................................................... 5
2.1 Components........................................................................................................................ 5
2.1.1 KiStudio Lab Software Package............................................................................. 5
2.1.2 Connectivity with KiConnect................................................................................... 6
2.1.3 KiDAQ and LabAmp Measurement Devices.......................................................... 6
2.1.4 KiDAQ Controller 5551A and Modules 55xxA........................................................ 7
2.1.5 KiDAQ Accessories.............................................................................................. 13
3. System Setup............................................................................................................................. 14
3.1 System Requirements....................................................................................................... 14
3.2 Software Installation.......................................................................................................... 14
3.2.1 Enable the Virtualization Technology................................................................... 14
3.2.2 Installation of KiStudio Lab................................................................................... 15
3.2.3 KiStudio Lab License Activation........................................................................... 15
3.2.4 Uninstallation of KiStudio Lab .............................................................................. 16
3.3 Connection Setup for Measurement Devices ................................................................... 16
3.3.1 KiDAQ Point-to-Point Setup................................................................................. 16
3.3.2 LabAmp Point-to-Point Setup............................................................................... 16
3.3.3 Mixed Setup: KiDAQ and LabAmp....................................................................... 17
4. KiStudio Lab Software Overview............................................................................................. 19
4.1 Project Board –Main View................................................................................................ 19
4.1.1 Project Devices .................................................................................................... 19
4.1.2 Measurement Setup............................................................................................. 20
4.1.3 Channel Overview................................................................................................ 21
4.1.4 Data Processing Definition................................................................................... 21
4.1.5 Dashboard Definition............................................................................................ 21
4.1.6 Signal Storage Selection...................................................................................... 22
4.2 Dashboard......................................................................................................................... 22
4.3 Project Browser................................................................................................................. 23
4.4 System Settings ................................................................................................................ 23
5. KiStudio Lab Features in Detail ............................................................................................... 25
5.1 Add a new Measurement Device...................................................................................... 25
5.2 Configure a KiDAQ Device................................................................................................ 25
5.2.1 Use different Sampling Rates .............................................................................. 25
5.2.2 Use Tare Functionality ......................................................................................... 26
5.2.3 Time Settings ....................................................................................................... 26
5.2.4 Configure KiDAQ Channels.................................................................................. 26
6. Configuration Examples........................................................................................................... 29
6.1 Torque Sensor 4503B with KiDAQ Module 5534A ........................................................... 29
6.1.1 Sensor Settings.................................................................................................... 29
6.1.2 Cabling ................................................................................................................. 30
6.1.3 Configuration of KiDAQ Module 5534A................................................................ 30

Content
5500A_002-943e-09.21 Page 3
7. Hardware Setup with Multiple Measurement Devices............................................................33
7.1 Connect Devices and PC with KiStudio Lab to Switch......................................................33
7.2 Configure Hirschmann Switch to run as PTP Master ........................................................34
7.3 Set Switch to be DHCP Server..........................................................................................34
7.4 Set the Switch Address and Time and save the Settings..................................................35
7.5 Finalization.........................................................................................................................35
8. Maintenance ...............................................................................................................................37
8.1 KiDAQ Device Factory Reset ............................................................................................37
8.2 KiStudio and KiDAQ Version Update.................................................................................37
8.2.1 KiDAQ Controller 5551A Firmware Update via USB ............................................38
8.2.2 KiDAQ Measurement Module Firmware Update ..................................................39
8.2.3 KiStudio Lab Update Installation...........................................................................40
8.3 Change of Battery in KiDAQ Controller 5551A..................................................................40
9. Troubleshooting.........................................................................................................................41
9.1 KiDAQ LED Status.............................................................................................................41
9.2 No Connection from PC to KiDAQ Device.........................................................................42
9.3 Unstable Connection from PC to Measurement Devices..................................................42
9.4 KiStudio Lab runs unstable................................................................................................43
10. Appendices.................................................................................................................................44
10.1 Safety Information for High Voltage Modules 5525A … 5528A ........................................44
10.2 Schematics of Accessories................................................................................................45
10.2.1 Cold Junction Compensation Type 5582Ax..........................................................45
10.2.2 Bridge Completion Type 5583Ax..........................................................................46

Type 5500A and 2910A
Page 4 5500A_002-943e-09.21
1. Introduction and Important Notes
Thank you for choosing a quality product from Kistler.
Please read this instruction manual carefully, so that you
can put the many properties of your product to optimal
use.
Kistler declines any liability, to the extent permissible by
law, if action is taken contrary to this instruction manual,
or other products are used than those listed as
accessories.
For assistance with any special questions remaining after
studying these instructions, Kistler customer service is
available around the world with expert advice for
application-specific problems.
1.1 Disposal Instructions for Electronic Devices
Do not discard old electronic instruments in municipal
trash. For disposal at end of life, please return this
product to an authorized local electronic waste disposal
service or contact the nearest Kistler Instruments sales
office for return instructions.
1.2 Software Upgrades and Updates
Kistler may from time to time supply upgrades or updates
for PC software and firmware. Such upgrades or updates
must always be installed.
Kistler declines any liability whatsoever for any direct or
consequential damage caused by products running on
software and firmware, which has not been upgraded or
updated with the latest software supplied.
1.3 Repairs at Kistler
Repairs at the Kistler factory can be arranged via the
local sales company.
Information can be found at www.kistler.com

System Overview
5500A_002-943e-09.21 Page 5
2. System Overview
With the KiDAQ data acquisition system, Kistler offers
engineers, researchers, measurement technicians and
students the opportunity to combine everything they need
for their measurement task in one setup. Various
measurands and sensors can be used with different data
acquisition hardware and be combined to a unified logical
measurement system –just according the application
requirements.
The KiDAQ data acquisition system offers a wide
selection of modules for various sensor technologies and
more than 20 different measurands –from simple voltage
signals across measurement bridges and IEPE sensors
to charge signals from piezoelectric sensors.
2.1 Components
2.1.1 KiStudio Lab Software Package
The KiStudio Lab software package consists of two
applications to acquire data with KiDAQ or LabAmp and
for comprehensive data analysis.
Measurement devices are configured efficiently with the
intuitive KiStudio Lab software, which provides an
overview of the whole measurement setup and enables
quick navigation.
Acquired data can be easily exported for analysis with
jBEAM. This powerful post-processing and analysis

Type 5500A and 2910A
Page 6 5500A_002-943e-09.21
software provides both, a comprehensive toolbox for
standard analysis and customizable calculations.
The package is available in two editions ‘Starter’or
‘Professional’. For details about the packages please see
the KiDAQ system datasheet 003-335e.
2.1.2 Connectivity with KiConnect
The intelligent KiConnect technology allows the user to
easily combine different measurement units to a logical
measurement setup and perform precise, time-
synchronized measurements thanks to the Precision
Time Protocol (PTP). KiConnect is built up on state-of-
the-art communications standards (TCP/IP and IoT-
principles) and is therefore ready for distributed setups
and cloud applications.
2.1.3 KiDAQ and LabAmp Measurement Devices
The KiDAQ hardware is designed in a modular way and
can be individually configured to match the required
measurement performance and channel count. The
Portable, Rack and DIN Rail models are designed so that
they can be optimally used in various applications.
Detail information, e.g. mechanical drawings, can be
found in the KiDAQ system datasheet 003-335e.
KiDAQ Rack
The 19" rack housing is 3 rack units high (3U) and can be
equipped with one controller and up to 13 selected
measurement modules. The housing is available in two
different versions: for standard 19” racks and with
carrying handle for desktop use.
KiDAQ Portable
The compact and scalable measurement system KiDAQ
Portable can be individually configured with one
controller and up to 13 measurement modules. It is
ideally suited for stationary and mobile measurement
tasks and thanks to the rugged aluminum enclosure it is
the ideal solution for various environments.
KiDAQ DIN Rail
The KiDAQ DIN Rail housing option provides simple
mounting on to standard rails according EN 60715. The
maximum number of modules depends on the required
data rate and the number of channels per module (e.g.
up to 16 channels with 100 kSps data rate or 256
channels with 10 kSps data rate or a combination).

System Overview
5500A_002-943e-09.21 Page 7
LabAmp family
The test setup can be extended as needed together with
other high-quality signal conditioning and data acquisition
systems from Kistler like LabAmp and –in future –with
selected devices from third-party manufacturers.
•LabAmp Type 5165A for dynamic charge measure-
ments (piezo-electric sensors), IEPE- or voltage-
measurements. 1 or 4 channels.
•LabAmp Type 5167A for quasi-static and dynamic
charge measurements (piezo-electric sensors). 4 or 8
channels.
2.1.4 KiDAQ Controller 5551A and Modules 55xxA
Description
A
Connector for 24 V power supply
(e.g. Type 5567A0)
B
Input for digital signals
C
USB Ports
•2x USB 2.0
D
Ethernet interfaces (RJ45) for connection to a network or
directly to a computer
E
Sensor inputs (for example 5509A):
•BNC neg.
•LEDs per input channel (module 5509A only)
F
Light emitting diodes (LEDs), which signify the status of the
corresponding measuring module (see description in chapter
9.1 below)
Controller Type 5551A
Every KiDAQ measurement device requires a controller
which provides power to the measurement modules and
ensures the proper configuration. The measurement data
is aggregated with a time-synchronized internal bus and
provided to the KiStudio Lab software with the KiConnect
protocol. This allows both local and remote setups over
standard networks.
For detail information and connector pinouts please refer
to KiDAQ system datasheet 003-335e.

Type 5500A and 2910A
Page 8 5500A_002-943e-09.21
Universal measurement module
Type 5501A
•2 analog input signals
oVoltage till 60 V
oCurrent
oResistance
oPotentiometer
oResistance thermometer (Pt100, Pt1000)
oThermocouples (types B,E,J,K,L,N,R,S,T,U)
oStrain gauges
oIEPE sensors (Piezotron)
•2 digital input signals
oStatus
•A/D conversion: 100 kSps (per channel), 24 bit
•Galvanic isolation (channel to channel to power supply
and to interface), isolation voltage: 500 VDC
For detail information and connector pinouts please refer
to KiDAQ system datasheet 003-335e.
Universal measurement module
Type 5502A
•4 analog input signals
oVoltage till 10 V
oCurrent
oResistance
oPotentiometer
oResistance thermometer (Pt100, Pt1000)
oThermocouples (types B,E,J,K,L,N,R,S,T,U)
oStrain gauges
oIEPE sensors (Piezotron)
•A/D conversion: 20 kSps (per channel), 24 bit
•Galvanic isolation (channel to channel to power supply
and to interface), isolation voltage: 500 VDC
For detail information and connector pinouts please refer
to KiDAQ system datasheet 003-335e.